XMC1100T016F0064ABXUMA1 - 32MHz 64KB Cortex-M0 | Infineon
Référence : XMC1100T016F0064ABXUMA1 ✓ ActifXMC1100T016F0064ABXUMA1 Présentation
An ARM Cortex-M0 microcontroller is a 32-bit reduced-instruction-set processor used in embedded control systems. The XMC1000 family combines that processor with Flash, SRAM, general-purpose I/O, timers, serial interfaces, and analog functions. This hierarchy places the device between a basic microcontroller and a more complex application processor: it provides enough deterministic control capability for sensor, actuator, and communication tasks without requiring an external memory interface or high-power processing core.
Key features include a 32 MHz ARM Cortex-M0 core, 64 KB of Flash, 16 KB of RAM, and a 16-pin TSSOP package with an exposed-pad package designation. Up to seven alternate output functions can be assigned to a port pin through the Pn_IOCR.PC register configuration, allowing peripherals to share external pins. These resources suit designs in which board area, BOM cost, and real-time responsiveness are more important than extensive memory capacity.
The AB-step XMC1100 datasheet describes the device as the superset of related derivative devices and explains that derivative-specific functions, ordering designations, and electrical characteristics can vary. Designers should consult the ordering table and pin-description section when assigning package pins. The exposed thermal pad requires careful PCB layout so that heat can move away from the device while preserving the electrical behavior expected by the selected pin configuration.
Typical uses include industrial sensor modules, small motor-control boards, building and appliance controls, communication equipment, and compact power-system controllers. The 64 KB Flash area can hold application firmware and configuration data, while 16 KB of SRAM supports working memory, buffers, protocol stacks, and real-time control loops. The combination of 32 MHz processing and integrated peripherals reduces the need for discrete support components in cost-sensitive embedded products.
When laying out the circuit, treat the exposed pad and associated pads according to the package drawing in the manufacturer datasheet. Preserve the recommended power and decoupling arrangement, route sensitive signals away from switching nodes, and confirm the complete pin map before finalizing the PCB. Firmware development can begin with the Cortex-M0 programming model, but peripheral configuration must follow the XMC1000 register definitions and AB-step documentation.
This product page combines the manufacturer’s XMC1100 AB-step technical documentation with ordering information, same-family alternatives, package details, and practical design guidance. It supports faster component selection while keeping the final schematic and firmware decisions anchored to the manufacturer datasheet and exact orderable part number.
Alternatives de remplacement direct pour XMC1100T016F0064ABXUMA1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec XMC1100T016F0064ABXUMA1 (même facteur de forme et même empreinte) — différant par Flash Memory, Package, Architecture, Core, Supply Voltage.
XMC1100T016F0064AAXUMA1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
XMC1100T016F0016ABXUMA1
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XMC1100T016X0016ABXUMA1
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
XMC1100T016X0064ABXUMA1
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →XMC1100-T016F0064-AB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
XMC1100T016F0064ABXUMA1 Valeurs maximales et caractéristiques électriques
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Core | ARM Cortex-M0 |
| CPU Frequency | 32 MHz |
| Flash Memory | 64 KB (64K x 8) |
| RAM | 16 KB |
| Architecture | 32-bit RISC |
| Series | XMC1000 |
| Device Variant | XMC1100-T016F0064-AB |
| Boîtier | PG-TSSOP-16-8 |
| Nombre de broches | 16 pins |
| Type de montage | Surface mount |
| Tension d'alimentation | 3.3 V / 5 V |
| Alternate Port Output Functions | Up to 7 functions per port pin |
| Product Temperature Class | Industrial |
| Peripheral Configuration | Pn_IOCR.PC port output configuration |
Guide de configuration des broches du XMC1100T016F0064ABXUMA1 pg-tssop-16-8
Configuration des broches du XMC1100T016F0064ABXUMA1 (boîtier pg-tssop-16-8). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour XMC1100T016F0064ABXUMA1.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
XMC1100T016F0064ABXUMA1 convient pour 6 applications: Industrial Sensor Controller, Small Motor-Control Board, Building and Appliance Control, Communication Equipment, Compact Power-System Controller, LED Lighting Controller.
Industrial Sensor Controller
The XMC1100T016F0064ABXUMA1 fits compact sensor modules that acquire measurements, apply digital filtering, and report results over a serial interface. Its 32 MHz ARM Cortex-M0 core provides timely execution for sampling schedules and protocol handling, while 64 KB of Flash accommodates application firmware and calibration tables. The 16 KB of RAM can support buffers and intermediate filter values. In a PG-TSSOP-16-8 package, the device also leaves PCB area for sensing, protection, and communication circuitry. Validate the selected peripheral assignments against the package pin table before layout.
Recommandé
Small Motor-Control Board
The XMC1100T016F0064ABXUMA1 can serve as the supervisory controller in a small motor-control design, handling command decoding, timing, fault states, and communication with a dedicated power stage. Its 32 MHz Cortex-M0 core is sufficient for deterministic supervisory tasks, while the 64 KB Flash and 16 KB RAM fit configuration logic and control buffers. The compact TSSOP package is useful when the board must coexist with power devices, current sensing, and protection components. Keep switching-node routing away from sensitive control signals and confirm that the application’s timing and protection requirements are met.
Recommandé
Building and Appliance Control
The XMC1100T016F0064ABXUMA1 is appropriate for compact appliance controls, building equipment, and user-interface subsystems that coordinate inputs, outputs, timers, and communications. Its 32 MHz processing rate supports responsive state-machine execution without a larger application processor, and the 64 KB Flash capacity provides room for control firmware and product configuration. The PG-TSSOP-16-8 package reduces board footprint in space-constrained products. Designers should use the pin-description table to allocate alternate peripheral functions and should preserve the manufacturer’s decoupling and exposed-pad layout recommendations.
Recommandé
Communication Equipment
The XMC1100T016F0064ABXUMA1 can act as a protocol controller or auxiliary communications processor in compact equipment. The 32 MHz ARM Cortex-M0 core handles framing, state management, buffer movement, and supervisory logic, while the 16 KB RAM can hold protocol state and transmit/receive buffers. The 64 KB Flash is sufficient for compact firmware rather than large protocol stacks. Its TSSOP-16 package suits small communication modules where component count and board area matter. Match the peripheral instance to the required serial interface and account for alternate port-function routing before PCB assignment.
Recommandé
Compact Power-System Controller
The XMC1100T016F0064ABXUMA1 can supervise power-system subsystems by reading operating conditions, sequencing commands, and coordinating protection or communication functions. A 32 MHz Cortex-M0 core supports deterministic control-loop tasks, while 64 KB of Flash and 16 KB of RAM are useful for supervisory code, parameter storage, and status buffering. The small PG-TSSOP-16-8 package helps limit board area around power components. Keep the control ground and signal routing compatible with the power stage, and use the manufacturer electrical limits to define isolation, filtering, and operating margins.
Recommandé
LED Lighting Controller
The XMC1100T016F0064ABXUMA1 is suitable for compact LED-lighting controllers that require timed outputs, user commands, diagnostics, and communication. Its 32 MHz Cortex-M0 performance allows fast state updates and timing management, while 64 KB of Flash holds lighting patterns, configuration, and control firmware. The 16 KB RAM supports status variables and communication buffers without external memory. The TSSOP-16-8 footprint helps create compact control boards. Allocate LED-control outputs only after checking their alternate functions and electrical characteristics, and maintain separation between switching outputs and sensitive control paths.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour XMC1100T016F0064ABXUMA1 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Use XMC1100T016F0064AAXUMA1 when its documented derivative characteristics satisfy the design and the AA device-step variant is the intended configuration. Use XMC1100T016F0016ABXUMA1 or XMC1100T016X0016ABXUMA1 only when 16 KB of Flash is genuinely sufficient; both provide 48 KB less program storage than the target. Use XMC1100T016X0064ABXUMA1 only after verifying its exact ordering characteristics. Because every listed candidate is from the same family and package, board-space reuse is possible, but memory, firmware, peripheral, pin-function, and qualification checks remain mandatory before substitution.
Comparaison avec les alternatives
| Paramètre | Ce produit | XMC1100T016F0064AAXUMA1 | XMC1100T016F0016ABXUMA1 | XMC1100T016X0016ABXUMA1 | XMC1100T016X0064ABXUMA1 | XMC1100-T016F0064-AB |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TSSOP-16-8 | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same |
| Flash Memory | 64 KB | 64 KB | 16 KB | 16 KB | 64 KB | 64 KB |
| Series | XMC1000 | XMC1000 | XMC1000 | XMC1000 | XMC1100 | XMC1100 |
Principaux différenciateurs
- Higher memory capacity within the same XMC1000 package (vs XMC1100T016F0016ABXUMA1)
- Four-times the Flash capacity of the reduced-density option (vs XMC1100T016X0016ABXUMA1)
- Matches the documented 64 KB Flash XMC1100 configuration (vs XMC1100-T016F0064-AB)
- Preserves 64 KB Flash in the documented X ordering family (vs XMC1100T016X0064ABXUMA1)
Notes de conception
Create the footprint from the Infineon PG-TSSOP-16-8 package drawing rather than a generic TSSOP-16 land pattern. The package designation includes an exposed-pad construction, so verify the pad count, exposed-pad dimensions, solder-mask opening, and paste pattern against the manufacturer drawing. Place the decoupling capacitor close to the device supply pin and provide a short, low-impedance return path to the appropriate ground reference.
Assign ports only after comparing the required peripheral functions with the package pin table. The XMC1100 supports up to seven alternate output functions on a port pin through Pn_IOCR.PC, but those functions still share the physical pad and its electrical characteristics. Leave no required function on a no-connect or unsuitable alternate-function pin, and verify that a peripheral instance does not conflict with another assigned peripheral.
Keep clock, reset, communication, and analog sensing paths short and away from switching nodes and high-current return paths. If the controller shares a board with relays, motor drivers, or power converters, route sensitive signals through the quiet side of the ground structure and add filtering at connector or switch inputs. The exact rise time and settling requirements should be checked in the manufacturer electrical-characteristics tables.
Do not substitute a same-package ordering code solely from the visible Flash and frequency fields. Device-step characters and derivative ordering codes can change available functions, and the 16 KB Flash alternatives have only one quarter of the target’s 64 KB capacity. Confirm the complete ordering table, pin functions, memory requirement, firmware image size, and peripheral set before approving a replacement.
Informations de conformité
The target is identified by Infineon as an industrial XMC1100 device. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.