XMC1100T016F0064ABXUMA1 - 32MHz 64KB Cortex-M0 | Infineon
MPN: XMC1100T016F0064ABXUMA1 ✓ 啟用中XMC1100T016F0064ABXUMA1 概覽
An ARM Cortex-M0 microcontroller is a 32-bit reduced-instruction-set processor used in embedded control systems. The XMC1000 family combines that processor with Flash, SRAM, general-purpose I/O, timers, serial interfaces, and analog functions. This hierarchy places the device between a basic microcontroller and a more complex application processor: it provides enough deterministic control capability for sensor, actuator, and communication tasks without requiring an external memory interface or high-power processing core.
Key features include a 32 MHz ARM Cortex-M0 core, 64 KB of Flash, 16 KB of RAM, and a 16-pin TSSOP package with an exposed-pad package designation. Up to seven alternate output functions can be assigned to a port pin through the Pn_IOCR.PC register configuration, allowing peripherals to share external pins. These resources suit designs in which board area, BOM cost, and real-time responsiveness are more important than extensive memory capacity.
The AB-step XMC1100 datasheet describes the device as the superset of related derivative devices and explains that derivative-specific functions, ordering designations, and electrical characteristics can vary. Designers should consult the ordering table and pin-description section when assigning package pins. The exposed thermal pad requires careful PCB layout so that heat can move away from the device while preserving the electrical behavior expected by the selected pin configuration.
Typical uses include industrial sensor modules, small motor-control boards, building and appliance controls, communication equipment, and compact power-system controllers. The 64 KB Flash area can hold application firmware and configuration data, while 16 KB of SRAM supports working memory, buffers, protocol stacks, and real-time control loops. The combination of 32 MHz processing and integrated peripherals reduces the need for discrete support components in cost-sensitive embedded products.
When laying out the circuit, treat the exposed pad and associated pads according to the package drawing in the manufacturer datasheet. Preserve the recommended power and decoupling arrangement, route sensitive signals away from switching nodes, and confirm the complete pin map before finalizing the PCB. Firmware development can begin with the Cortex-M0 programming model, but peripheral configuration must follow the XMC1000 register definitions and AB-step documentation.
This product page combines the manufacturer’s XMC1100 AB-step technical documentation with ordering information, same-family alternatives, package details, and practical design guidance. It supports faster component selection while keeping the final schematic and firmware decisions anchored to the manufacturer datasheet and exact orderable part number.
直接替換替代品,適用於 XMC1100T016F0064ABXUMA1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XMC1100T016F0064ABXUMA1 (相同外形與佔位) — 差異在於 Flash Memory, Package, Architecture, Core, Supply Voltage.
XMC1100T016F0064AAXUMA1
✅ 直接替換📋 參考替代品(不在目錄中)
XMC1100T016F0016ABXUMA1
✅ 直接替換聯絡詢價
查看資料表 →XMC1100T016X0016ABXUMA1
✅ 直接替換📋 參考替代品(不在目錄中)
XMC1100T016X0064ABXUMA1
✅ 直接替換聯絡詢價
查看資料表 →XMC1100-T016F0064-AB
✅ 直接替換📋 參考替代品(不在目錄中)
XMC1100T016F0064ABXUMA1 最大額定值與電氣特性
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| Core | ARM Cortex-M0 |
| CPU Frequency | 32 MHz |
| Flash Memory | 64 KB (64K x 8) |
| RAM | 16 KB |
| Architecture | 32-bit RISC |
| Series | XMC1000 |
| Device Variant | XMC1100-T016F0064-AB |
| 封裝 | PG-TSSOP-16-8 |
| 腳位數 | 16 pins |
| 安裝類型 | Surface mount |
| 供應電壓 | 3.3 V / 5 V |
| Alternate Port Output Functions | Up to 7 functions per port pin |
| Product Temperature Class | Industrial |
| Peripheral Configuration | Pn_IOCR.PC port output configuration |
XMC1100T016F0064ABXUMA1 pg-tssop-16-8 腳位配置指南
XMC1100T016F0064ABXUMA1(pg-tssop-16-8 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XMC1100T016F0064ABXUMA1.
請參閱 資料表 以查看完整腳位配置。
典型應用
XMC1100T016F0064ABXUMA1 適用於 6 應用s: Industrial Sensor Controller, Small Motor-Control Board, Building and Appliance Control, Communication Equipment, Compact Power-System Controller, LED Lighting Controller.
Industrial Sensor Controller
The XMC1100T016F0064ABXUMA1 fits compact sensor modules that acquire measurements, apply digital filtering, and report results over a serial interface. Its 32 MHz ARM Cortex-M0 core provides timely execution for sampling schedules and protocol handling, while 64 KB of Flash accommodates application firmware and calibration tables. The 16 KB of RAM can support buffers and intermediate filter values. In a PG-TSSOP-16-8 package, the device also leaves PCB area for sensing, protection, and communication circuitry. Validate the selected peripheral assignments against the package pin table before layout.
推薦
Small Motor-Control Board
The XMC1100T016F0064ABXUMA1 can serve as the supervisory controller in a small motor-control design, handling command decoding, timing, fault states, and communication with a dedicated power stage. Its 32 MHz Cortex-M0 core is sufficient for deterministic supervisory tasks, while the 64 KB Flash and 16 KB RAM fit configuration logic and control buffers. The compact TSSOP package is useful when the board must coexist with power devices, current sensing, and protection components. Keep switching-node routing away from sensitive control signals and confirm that the application’s timing and protection requirements are met.
推薦
Building and Appliance Control
The XMC1100T016F0064ABXUMA1 is appropriate for compact appliance controls, building equipment, and user-interface subsystems that coordinate inputs, outputs, timers, and communications. Its 32 MHz processing rate supports responsive state-machine execution without a larger application processor, and the 64 KB Flash capacity provides room for control firmware and product configuration. The PG-TSSOP-16-8 package reduces board footprint in space-constrained products. Designers should use the pin-description table to allocate alternate peripheral functions and should preserve the manufacturer’s decoupling and exposed-pad layout recommendations.
推薦
Communication Equipment
The XMC1100T016F0064ABXUMA1 can act as a protocol controller or auxiliary communications processor in compact equipment. The 32 MHz ARM Cortex-M0 core handles framing, state management, buffer movement, and supervisory logic, while the 16 KB RAM can hold protocol state and transmit/receive buffers. The 64 KB Flash is sufficient for compact firmware rather than large protocol stacks. Its TSSOP-16 package suits small communication modules where component count and board area matter. Match the peripheral instance to the required serial interface and account for alternate port-function routing before PCB assignment.
推薦
Compact Power-System Controller
The XMC1100T016F0064ABXUMA1 can supervise power-system subsystems by reading operating conditions, sequencing commands, and coordinating protection or communication functions. A 32 MHz Cortex-M0 core supports deterministic control-loop tasks, while 64 KB of Flash and 16 KB of RAM are useful for supervisory code, parameter storage, and status buffering. The small PG-TSSOP-16-8 package helps limit board area around power components. Keep the control ground and signal routing compatible with the power stage, and use the manufacturer electrical limits to define isolation, filtering, and operating margins.
推薦
LED Lighting Controller
The XMC1100T016F0064ABXUMA1 is suitable for compact LED-lighting controllers that require timed outputs, user commands, diagnostics, and communication. Its 32 MHz Cortex-M0 performance allows fast state updates and timing management, while 64 KB of Flash holds lighting patterns, configuration, and control firmware. The 16 KB RAM supports status variables and communication buffers without external memory. The TSSOP-16-8 footprint helps create compact control boards. Allocate LED-control outputs only after checking their alternate functions and electrical characteristics, and maintain separation between switching outputs and sensitive control paths.
推薦
推薦產品摘要
工程參考資料,適用於 XMC1100T016F0064ABXUMA1 — 比較、設計指引及合規資訊。
選型指南
Use XMC1100T016F0064AAXUMA1 when its documented derivative characteristics satisfy the design and the AA device-step variant is the intended configuration. Use XMC1100T016F0016ABXUMA1 or XMC1100T016X0016ABXUMA1 only when 16 KB of Flash is genuinely sufficient; both provide 48 KB less program storage than the target. Use XMC1100T016X0064ABXUMA1 only after verifying its exact ordering characteristics. Because every listed candidate is from the same family and package, board-space reuse is possible, but memory, firmware, peripheral, pin-function, and qualification checks remain mandatory before substitution.
與替代品比較
| 參數 | 本產品 | XMC1100T016F0064AAXUMA1 | XMC1100T016F0016ABXUMA1 | XMC1100T016X0016ABXUMA1 | XMC1100T016X0064ABXUMA1 | XMC1100-T016F0064-AB |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TSSOP-16-8 | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same | PG-TSSOP-16-8 - same |
| Flash Memory | 64 KB | 64 KB | 16 KB | 16 KB | 64 KB | 64 KB |
| Series | XMC1000 | XMC1000 | XMC1000 | XMC1000 | XMC1100 | XMC1100 |
主要差異化特點
- Higher memory capacity within the same XMC1000 package (對比XMC1100T016F0016ABXUMA1)
- Four-times the Flash capacity of the reduced-density option (對比XMC1100T016X0016ABXUMA1)
- Matches the documented 64 KB Flash XMC1100 configuration (對比XMC1100-T016F0064-AB)
- Preserves 64 KB Flash in the documented X ordering family (對比XMC1100T016X0064ABXUMA1)
設計說明
Create the footprint from the Infineon PG-TSSOP-16-8 package drawing rather than a generic TSSOP-16 land pattern. The package designation includes an exposed-pad construction, so verify the pad count, exposed-pad dimensions, solder-mask opening, and paste pattern against the manufacturer drawing. Place the decoupling capacitor close to the device supply pin and provide a short, low-impedance return path to the appropriate ground reference.
Assign ports only after comparing the required peripheral functions with the package pin table. The XMC1100 supports up to seven alternate output functions on a port pin through Pn_IOCR.PC, but those functions still share the physical pad and its electrical characteristics. Leave no required function on a no-connect or unsuitable alternate-function pin, and verify that a peripheral instance does not conflict with another assigned peripheral.
Keep clock, reset, communication, and analog sensing paths short and away from switching nodes and high-current return paths. If the controller shares a board with relays, motor drivers, or power converters, route sensitive signals through the quiet side of the ground structure and add filtering at connector or switch inputs. The exact rise time and settling requirements should be checked in the manufacturer electrical-characteristics tables.
Do not substitute a same-package ordering code solely from the visible Flash and frequency fields. Device-step characters and derivative ordering codes can change available functions, and the 16 KB Flash alternatives have only one quarter of the target’s 64 KB capacity. Confirm the complete ordering table, pin functions, memory requirement, firmware image size, and peripheral set before approving a replacement.
合規資訊
The target is identified by Infineon as an industrial XMC1100 device. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.