מוצרים (44,000+)

TC7S66FU - 5-Pin SPST Analog Switch | Toshiba
TC7S66FU

TC7S66FU - 5-Pin SPST Analog Switch | Toshiba

The Toshiba TC7S66FU is a single-pole single-throw (SPST) bilateral analog switch in a 5-pin SOT-353 (USV) package, fabricated in Toshiba's L-MOS (Low-power MOS) high-speed process. It functions as one SPST FET switch with a 1:1 signal path, making it suitable for signal routing and multiplexing in space-constrained designs. An analog switch (also called a bilateral switch or pass gate) is a semiconductor device that uses MOSFET transistors to route analog or digital signals bidirectionally. Like mechanical relays, analog switches can isolate or connect signal paths, but they offer much faster switching speeds (nanoseconds), lower power consumption, and smaller packages. Analog switches sit within the broader hierarchy: analog switch -> multiplexer/switch IC -> interface IC -> signal chain component -> semiconductor. The bilateral nature means either terminal can act as input or output. Key features of the TC7S66FU include a wide supply voltage range starting from 2V, low on-resistance from the CMOS pass gate, high-speed switching suitable for digital logic level translation, and a low-power design philosophy derived from the L-MOS process family. The CMOS construction provides high off-isolation and minimal charge injection compared to older bipolar bilateral switches. Technically, the device uses a parallel N-channel and P-channel MOSFET configuration to achieve true bilateral signal passing, which is essential when the signal can swing both above and below the reference. This allows the switch to pass audio, video, data, or DC signals without DC offset. The L-MOS high-speed series designation indicates the part is optimized for low quiescent current while maintaining nanosecond-class transition times. Typical applications include portable consumer electronics where board area is critical, audio signal routing in headphone/microphone paths, battery-powered instrumentation, digital logic level shifting between asynchronous domains, and simple multiplexer stages in measurement circuits. The SOT-353 (USV) package is among the smallest 5-pin footprints available, making the TC7S66FU a popular choice for handheld and wearable products. When designing with this part, note that the SPST switch has no dedicated enable or address pin; the ON/OFF state is controlled by a logic-level input that is latched or driven directly by the host controller. Ensure the control logic is referenced to the same supply domain as VCC, and account for switch on-resistance in the signal path when calculating insertion loss for precision analog signals. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in alternatives from the same Toshiba L-MOS family, and practical design guidance that complements the manufacturer datasheet.

RFQ צור קשר
TC850ILW713 - 15-Bit Plus Sign Dual-Slope ADC | Microchip
TC850ILW713

TC850ILW713 - 15-Bit Plus Sign Dual-Slope ADC | Microchip

The Microchip Technology TC850ILW713 is a 15-bit resolution plus sign bit (16-bit total conversion width) integrating analog-to-digital converter (ADC) that performs up to 40 conversions per second using a dual-slope conversion technique. Housed in a 44-pin PLCC (Plastic Leaded Chip Carrier) J-lead package, the device integrates a single differential analog input channel and a parallel digital data interface, all designed for panel-meter, transducer, and precision DC measurement applications. Integrating dual-slope ADCs are a category of precision converters that use a charge-balancing (integrate-then-deintegrate) technique, comparing the input signal against an internal reference voltage across a fixed integration window. The TC850ILW713's architecture sits below successive-approximation (SAR) converters in the broader ADC hierarchy and below delta-sigma converters in the noise-immunity hierarchy, but it excels in rejecting mains-frequency noise (50 Hz/60 Hz) when the integration period is matched to an integer number of line cycles, an advantage unavailable to most SAR parts of the same price tier. Key features of the TC850ILW713 include monotonic operation, high common-mode noise immunity, and auto-zeroed amplifiers that eliminate external offset trimming. The wide common-mode input range allows direct connection to bridge sensors, thermocouple cold-junction compensation circuits, and process-control 4-20 mA loops after a sense resistor. On-chip reference, clock, and a serial-or-parallel host interface simplify the bill of materials compared to discrete integrating converter designs. Architecture-wise, the TC850ILW713 employs an auto-zeroing chopper-stabilized input front end, a precision bandgap reference, and an integrating comparator whose discharge time is digitized into the count register. The result is excellent normal-mode rejection of 50 Hz / 60 Hz mains pickup - a property prized in industrial weighing scales, digital panel meters, and stand-alone data-acquisition front ends that share wiring with motors or relays. Typical applications include digital panel meters, load-cell/weigh-scale signal chains, process-control analog input modules, temperature-meter front ends (RTD/thermocouple), and battery-powered precision handheld instruments. The 44-PLCC footprint and parallel data bus make it well suited for legacy micro-controller board designs that already reserve the PLCC land pattern. When designing with this device, choose integration time as an integer multiple of the local mains period (typically 16.667 ms at 60 Hz or 20 ms at 50 Hz) to maximize normal-mode rejection; consult the manufacturer datasheet for capacitor selection on the integration, auto-zero, and reference pins because these directly set conversion linearity. This page synthesizes distributor pricing, drop-in alternatives in the same 44-PLCC footprint, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
TCA0372BDP1 - 1A Dual Power Op Amp 5-40V | onsemi
TCA0372BDP1

TCA0372BDP1 - 1A Dual Power Op Amp 5-40V | onsemi

The onsemi TCA0372BDP1 is a dual power operational amplifier with two independent amplifier channels, a 5 V to 40 V supply range, and output-current capability up to 1 A per channel. The device is packaged in an 8-pin plastic dual in-line package designated 8-PDIP and is intended for power stages driving loads that exceed the current range of conventional operational amplifiers. A power operational amplifier is an operational amplifier integrated with output-driver circuitry capable of supplying substantially higher load current. The TCA0372 family occupies the power-amplifier segment of the operational-amplifier hierarchy and is commonly positioned between general-purpose signal amplifiers and discrete transistor output stages. Its dual-channel architecture allows one package to drive two independent loads or to provide a complementary output arrangement when configured appropriately. The main feature is high output-current capability of 1.0 A, allowing the amplifier to drive inductive, resistive, and capacitive loads more effectively than a conventional small-signal op amp. The 5 V to 40 V operating supply range supports higher-voltage systems than many low-voltage integrated amplifiers. According to the onsemi product page and manufacturer datasheet, the circuit is intended for servo amplifiers and power supplies, with no deadband crossover distortion intended to improve operation when driving coils. Each channel contains an error amplifier followed by high-current output capability, allowing feedback to control the voltage delivered to the load. The power bipolar output stage can sink and source current, while external resistors and capacitors establish gain, bandwidth, stability, and output bias in the completed circuit. The high current capability does not remove the need to observe output-stage limits, load transients, supply decoupling, thermal conditions, and output-voltage headroom. Typical uses include DC servo amplifiers, power-supply error amplifiers, audio and motor-control power stages, and industrial actuator drivers. The dual configuration can reduce component count in mirrored or dual-axis systems. For single-channel designs, one channel may remain unused, subject to the manufacturer's recommended input and output termination arrangements. PCB layout should keep feedback routing short and place supply-bypass capacitors close to the device. Because output current can reach 1 A, copper width, connector sizing, thermal dissipation, and load-return paths become important. Designers should also use protection or snubber networks when switching highly reactive loads because feedback alone cannot absorb unlimited inductive energy. This product page consolidates the confirmed electrical ratings, package information, sourcing structure, drop-in candidates, and application guidance for TCA0372BDP1. It also identifies which comparison details require verification against the manufacturer datasheet, helping engineers plan a controlled redesign and validation process rather than relying only on a generic amplifier substitution.

RFQ צור קשר
TCA0372DP1 - 1A Dual Power Operational Amplifier | onsemi
TCA0372DP1

TCA0372DP1 - 1A Dual Power Operational Amplifier | onsemi

onsemi TCA0372DP1 is a dual-channel power operational amplifier intended for high-current amplifier stages, servo amplifiers, power supplies, and inductive loads. The device operates from a 5 V to 40 V supply range, provides output current up to 1.0 A, and uses a 1.4 MHz gain-bandwidth product. It is packaged in an 8-pin PDIP. Its monolithic power-output stage is designed to reduce crossover distortion when driving coils, making the TCA0372DP1 useful in systems where conventional small-signal operational amplifiers cannot deliver adequate load current. A power operational amplifier is an operational amplifier integrated with an output stage capable of supplying substantially more current than a conventional precision amplifier. This places the device within the hierarchy of operational amplifier, linear amplifier, analog signal amplifier, and integrated circuit. Unlike a switching regulator, the TCA0372DP1 amplifies an analog error or control signal while maintaining continuous conduction. Its power-output capability allows one dual amplifier package to serve both error amplification and high-current drive functions in feedback-controlled systems. The primary headline characteristics are a 1.0 A maximum output current, a 5 V to 40 V operating supply range, and a 1.4 MHz gain-bandwidth product. The dual configuration provides two amplifier channels in one package, reducing board area in multi-axis servo or dual-channel drive systems. The lack of dead-band crossover distortion is particularly relevant when driving inductive coils because it avoids the command dead zone commonly introduced by power-output stages that switch between positive and negative drive states. The TCA0372 is a monolithic circuit, allowing its internal drive and amplifier sections to share a common package and support direct analog feedback-control operation. In a typical servo amplifier, an external position or speed loop generates a command voltage, and the TCA0372 channel amplifies that command into a motor-drive signal. Feedback from the actuator closes the loop. The wide operating-voltage range also permits use with higher-voltage power systems when the remaining input, output, and thermal requirements are satisfied. Typical uses include servo-amplifier output stages, closed-loop motor controllers, industrial actuator drivers, power-supply error amplifiers, and other systems that require analog feedback with a high-current output. For AC or bipolar drive arrangements, the external network must handle the required current and voltage excursions without exceeding the device's electrical limits. Heat management and output-stage stability are important when continuous load operation approaches the output-current rating. Circuit implementation should preserve the feedback connection at the amplifier output and minimize PCB-trace resistance between the power-output pins and the load. Input and output decoupling should follow the manufacturer's recommended application circuit. Because the amplifier dissipates power internally, designers should calculate worst-case output dissipation, provide adequate copper area, and verify that the ambient temperature and load waveform keep junction temperature within the qualified operating range. This product page combines the exact TCA0372DP1 electrical and package identifiers with datasheet references, application guidance, and a package-aware comparison. It also distinguishes documented functions from parameters requiring confirmation in the manufacturer datasheet. The result is a practical engineering reference for evaluating whether this dual, high-current operational amplifier matches a servo, power-supply, or inductive-drive design without confusing it with a switching power converter.

RFQ צור קשר
TCA0372DP1G - 1A Dual Power Op Amp | onsemi
TCA0372DP1G

TCA0372DP1G - 1A Dual Power Op Amp | onsemi

The onsemi TCA0372DP1G is a dual monolithic power operational amplifier capable of delivering 1.0 A output current from a 5 V to 40 V supply in an 8-pin PDIP package. The device provides two power operational-amplifier channels, a unity-gain bandwidth of 1.4 MHz, a nominal common-mode rejection ratio of 90 dB, and an input offset voltage as high as 20 mV. Its extended-temperature grade supports applications beyond the standard commercial temperature range. A power operational amplifier is a voltage-controlled amplifier that combines the high input impedance and closed-loop control of an ordinary operational amplifier with substantially greater output-current capability. Within the power-management and signal-chain hierarchy, the TCA0372 belongs to the amplifier IC family and is commonly used where a low-level error or control signal must directly drive a coil, motor winding, speaker, or power-supply output stage. The TCA0372's 1.0 A output-current capability makes it suitable for servo amplifiers, regulated power supplies, and industrial actuator drivers. Its no-dead-band crossover-distortion characteristic improves drive into inductive coils compared with solutions exhibiting an output transition dead zone. The two independent channels also permit mirrored, complementary, or dual-axis motion-control architectures while preserving identical amplifier characteristics. The monolithic dual-amplifier design simplifies system implementation by placing two power op-amp channels in one package. The 1.4 MHz unity-gain bandwidth supports applications that require both low-frequency loop control and useful bandwidth for dynamic feedback systems. The 90 dB nominal common-mode rejection ratio helps isolate the input stage from common-mode disturbances, while the 20 mV maximum input offset voltage defines the practical DC error boundary that must be considered in precision servo loops. Typical uses include servo-motor control, audio output stages, power-supply regulation, industrial positioning systems, and actuator drivers. Two amplifiers in one PDIP package can reduce board area when a system requires dual-axis control or complementary drive. Where the load is inductive, flyback current must be controlled with an external clamp path, and where the load is capacitive, stability must be checked using the feedback network and load conditions. The primary design tradeoff is sustained output-current capability versus heat generated inside the 8-pin PDIP package. A 1.0 A rating does not imply that every load condition can be driven continuously without thermal analysis. Verify copper area, ambient temperature, output duty cycle, voltage headroom, and required safety margin before using the full current rating. Follow the onsemi datasheet for recommended compensation, bias-pin bypass, and application-circuit details. This page organizes the key electrical limits, application guidance, drop-in candidates, and package-level design considerations for engineers evaluating the TCA0372DP1G in dual power-amplifier systems.

RFQ צור קשר
TCA0372DP2 - 1A Dual Power Op Amp | onsemi
TCA0372DP2

TCA0372DP2 - 1A Dual Power Op Amp | onsemi

onsemi TCA0372DP2 is a dual power operational amplifier delivering up to 1.0 A output current and operating from a 5 V to 40 V supply in an 8-pin PDIP package. The monolithic device is designed for servo amplifiers, power supplies, and inductive loads, with no deadband crossover distortion to improve coil-drive performance. A power operational amplifier is a high-current linear amplifier that combines the gain and signal handling of a conventional operational amplifier with the ability to source or sink substantial load current. Within the amplifier hierarchy, it belongs to the power-amplifier class rather than the general-purpose low-current op-amp category. Its practical role is to turn a low-level control signal into a high-current drive for motors, solenoids, and other demanding loads. The TCA0372 family provides two independent amplifier channels, 1.0 A output-current capability per power-amplifier stage, and a 5 V to 40 V operating range. The absence of deadband crossover distortion is particularly useful when driving coils because the output crosses through zero more linearly than a conventional output stage with a dead region. This characteristic can reduce drive dead zone in bidirectional servo and actuator systems. The monolithic power-amplifier architecture supports relatively demanding loads without requiring a separate external power-transistor stage. Because the device combines amplification and current delivery in one package, the surrounding design must still account for supply decoupling, output-current limits, thermal dissipation, and protection against inductive voltage spikes. Its wide 40 V maximum supply rating provides useful headroom for industrial and automotive-style actuator systems. Typical applications include servo-amplifier loops, power-supply control stages, relay and solenoid drivers, motor-control systems, and other inductive or high-current loads. The dual-channel configuration can also support two coordinated actuator channels or one control function plus a complementary auxiliary function, subject to the applicable electrical and thermal limits. For a new design, preserve adequate supply decoupling near the device, verify the continuous and peak current requirements of the connected load, and provide suitable flyback protection for inductive loads. The through-hole PDIP package is straightforward for prototype and legacy industrial assemblies, although a surface-mount power-amplifier option may be preferable for compact production hardware. This product overview combines the confirmed 1.0 A current, 5 V to 40 V supply range, dual-channel architecture, no-deadband feature, and PDIP-8 format with practical guidance for amplifier selection, PCB implementation, thermal review, and drop-in replacement assessment.

RFQ צור קשר
TCA0372DP2G - Dual 1A Power Op Amp | onsemi
TCA0372DP2G

TCA0372DP2G - Dual 1A Power Op Amp | onsemi

The onsemi TCA0372DP2G is a dual power operational amplifier rated for a 1.0 A output current and a 5 V to 40 V supply range in a 16-pin PDIP package. Its two amplifier channels are designed for power-level signal conditioning, including servo amplifiers, power supplies, and inductive loads. The manufacturer identifies the TCA0372 family as a monolithic dual power operational amplifier with no deadband crossover distortion. A power operational amplifier is an integrated circuit that combines the voltage gain of an operational amplifier with the drive capability of a power output stage. This places the component in the amplifier IC hierarchy between precision signal amplifiers and discrete power-transistor stages. Its purpose is to amplify a low-level control signal while providing enough output current to drive loads that a conventional small-signal operational amplifier cannot handle directly. The most important device-level specifications are the 1.0 A output-current capability, 5 V to 40 V operating supply range, 1.4 MHz bandwidth indication, and dual-channel configuration. The extended-temperature marking distinguishes this exact ordering code from catalog entries with narrower environmental coverage. Its power-output topology is particularly relevant when driving coils, motors, solenoids, or other loads where the output must remain linear across positive and negative signal excursions. The two channels share the same monolithic power-amplifier architecture and are intended for applications requiring substantial output current without the discrete driver circuitry normally associated with power stages. Eliminating deadband crossover distortion can simplify feedback-loop design in bipolar or bidirectional drive systems because the output follows the command signal more directly around zero. Engineers should nevertheless account for supply headroom, output-current limits, load return paths, and the thermal load created during sustained high-current operation. Typical uses include servo-amplifier control loops, regulated power-supply error amplifiers, motor and solenoid drivers, audio amplification, and industrial actuator interfaces. The 16-pin PDIP format favors through-hole construction and repairable assemblies. The same package can also support prototype and legacy-system maintenance where a high-current output stage must fit an existing dual-in-line board layout. A robust design should use low-inductance supply and ground connections, place input and feedback components close to the relevant pins, and provide adequate copper and thermal dissipation around the output path. Feedback compensation and stability must be evaluated with the actual load impedance and cable capacitance. Current limiting or protection may also be required when the load can exceed the device's 1.0 A rating or develop an abrupt fault condition. This product page combines the manufacturer datasheet, distributor catalog information, package details, lifecycle context, application guidance, and drop-in-replacement analysis. It is designed to support component selection, PCB planning, sourcing, and design review for engineers working with high-current dual power operational amplifiers.

RFQ צור קשר
TCA0372DW - Dual 1A Power Op Amp | onsemi | 16-SOIC
TCA0372DW

TCA0372DW - Dual 1A Power Op Amp | onsemi | 16-SOIC

onsemi TCA0372DW is a dual power operational amplifier with 1.0 A output current, a 5 V to 40 V operating range, and a 16-lead SOIC package. The device is intended to amplify low-level error signals directly into high-current loads without adding a separate power-output stage. Its dual-circuit configuration allows two independent power-amplifier channels within one package, reducing board area in multi-axis motion, audio, and power-control systems. A power operational amplifier is a specialized operational amplifier that combines high-voltage signal handling, low-voltage input amplification, and current-drive capability. Within the product hierarchy, it belongs to the operational-amplifier family, amplifier IC family, analog signal-conditioning category, and broader semiconductor category. Unlike a conventional small-signal operational amplifier, the TCA0372 is designed to drive coils, motors, and other loads that require substantially more output current than a standard op amp can supply. The principal verified features include 1.0 A output current, dual power-amplifier operation, a 5 V to 40 V supply range, and operation without deadband crossover distortion. The absence of deadband crossover distortion is especially relevant when the amplifier drives coils because it avoids the output transition region that can introduce nonlinear behavior around zero. According to the onsemi manufacturer datasheet, the monolithic circuit is intended for power supplies and servo amplifiers as well as coil-driving applications. The TCA0372 integrates input amplification and power-output capability in one monolithic device, reducing the number of external drive stages required in a power-control design. Two amplifiers are provided in the package, allowing a dual-axis actuator system or two independent power channels to share one 16-SOIC package. Its wide 5 V to 40 V operating range supports applications operating from conventional industrial rails through higher-voltage motor-control systems. Typical uses include DC servo amplifiers, closed-loop position and speed control, audio power stages, industrial actuator drivers, and power-supply error amplifiers. In a servo loop, the TCA0372 can convert a low-level feedback error into a high-current motor command. For audio, its dual-channel organization can support left and right channels when the load and thermal conditions permit. In power supplies, its output current and high-voltage capability can drive suitable external stages when the required operating point remains within the datasheet limits. Designers should verify the complete electrical characteristics, pin connections, thermal limits, and output-stage behavior in the onsemi datasheet before layout. Decoupling must minimize output-stage transients and supply noise, while PCB copper and thermal design must accommodate dissipation during sustained high-current operation. The 16-pin SOIC footprint also requires adequate spacing from heat-generating components because its relatively small lead frame can limit heat dissipation. This product record combines verified manufacturer and distributor information, same-family replacement analysis, parameter-level comparison, and practical engineering guidance. It distinguishes confirmed TCA0372DW facts from specification fields that were not supplied in the retrieved data, helping engineers make evidence-based sourcing and design decisions.

RFQ צור קשר
TCA0372DWG - 1A Dual Power Op Amp | onsemi | 16-SOIC
TCA0372DWG

TCA0372DWG - 1A Dual Power Op Amp | onsemi | 16-SOIC

The onsemi TCA0372DWG is a dual power operational amplifier with 1.0 A output current, a 5 V to 40 V operating supply range, and a 16-pin SOIC package. Designed for power-buffer, servo-amplifier, power-supply, and coil-driving applications, the device combines two amplifiers in one package while supporting output currents of 1.0 A. A power operational amplifier is a high-current amplifier that sits between a low-power control signal and a load such as a motor, solenoid, actuator, or power-conversion stage. It belongs to the operational-amplifier hierarchy, amplifier family, and broader analog and power-management semiconductor categories. Unlike a conventional low-current signal op amp, a power op amp is intended to provide substantially greater load-driving capability while preserving closed-loop control of voltage or current. Key characteristics of the TCA0372DWG include 1.0 A output current, a 1.4 MHz gain-bandwidth product, and a 1.3 V/µs slew rate. Its operating supply range extends from 5 V to 40 V, making it appropriate for industrial, audio, servo, and power-control systems that operate above conventional ±15 V laboratory supply levels. The device also uses a no-deadband output architecture, which improves behavior when driving inductive coils. The TCA0372 is a monolithic dual circuit, allowing independent use of the two amplifier sections when their supply and thermal requirements permit. Its 1.4 MHz bandwidth supports applications requiring more bandwidth than a slow power-buffer stage while its 1.3 V/µs slew rate provides comparatively fast voltage transitions. These characteristics make it suitable for audio power stages, servo loops, motor-control paths, and power-supply control loops. Typical applications include servo amplifiers, regulated power supplies, audio amplifiers, motor drivers, actuator controllers, and coil drivers. The 1.0 A output capability is important when the load draws substantially more current than a standard precision op amp can deliver. Designers should still evaluate the SOA limits, supply capability, output saturation, load impedance, and thermal dissipation for the exact operating conditions. For reliable layout, keep feedback and compensation components close to the amplifier pins, provide robust supply decoupling, and use a PCB copper area that can remove heat generated at high output current. Avoid driving the output into excessive capacitive loads, and include current limiting or protection where the connected coil or actuator can present an unusual startup transient. This product data consolidates the manufacturer specifications, package information, sourcing details, same-family alternatives, comparison parameters, and practical design guidance into an engineering-oriented reference for selecting and implementing the TCA0372DWG.

RFQ צור קשר
TCA0372DWR2 - Dual Power Op-Amp 1A SOIC-16 | onsemi
TCA0372DWR2

TCA0372DWR2 - Dual Power Op-Amp 1A SOIC-16 | onsemi

The onsemi TCA0372DWR2 is a dual power operational amplifier delivering up to 1.0 A output current per channel, operating from supply rails of 5 V to 40 V (or ±20 V dual supply), housed in a 16-pin wide SOIC (SOIC-16 W, DW suffix) surface-mount package. A power operational amplifier is an op-amp that combines the precision input stage and high open-loop gain of a standard operational amplifier with an output stage capable of sourcing or sinking currents in the ampere range, far beyond the tens of milliamps typical of general-purpose op-amps. In the power-management and signal-chain hierarchy, the TCA0372 sits between standard op-amps and fully integrated audio or motor driver ICs: it is an amplifier - specifically a power op-amp - classified under operational amplifiers / buffer amplifiers in vendor taxonomies. Key differentiating features of the TCA0372 include the 1.0 A continuous output current rating, a gain-bandwidth product around 1.4 MHz with a 1.4 V/us slew rate, and operation on a single supply from 5 V to 40 V or on dual supplies up to ±20 V. The device is internally compensated and, critically, exhibits no deadband crossover distortion in the output stage, which is essential when driving inductive loads such as coils, actuators, and servo motors where crossover artifacts translate directly into torque ripple or audible distortion. Architecturally, the TCA0372 is a monolithic bipolar device integrating two complete power op-amp channels on a single die. The wide-body SOIC-16 package provides substantially better thermal dissipation than a standard SOIC-8, allowing both channels to drive heavy loads when adequate PCB copper is provided. Internal thermal limiting and safe-area considerations typical of power output stages protect the device during faults, though board-level thermal design remains the designer's responsibility at sustained high current. Typical applications include servo amplifiers for position control, power supplies as error amplifiers or pass-element drivers, coil and solenoid drivers, motor control subcircuits, audio power output stages, and general power buffering where a standard op-amp cannot supply the required load current. When designing with the TCA0372, account for package power dissipation: at 1 A output across a large input-to-output voltage differential, junction temperature rise is dominated by the SOIC-16 thermal resistance, so generous copper pours on the output-stage pins are recommended. This page adds value beyond the manufacturer datasheet by consolidating drop-in replacement options (TCA0372DWR2G, TCA0372BDWR2G, NCV0372B variants), application guidance, and comparison data in one place for sourcing and design engineers.

RFQ צור קשר
TCA1116PWR - 16-Bit I2C I/O Expander | Texas Instruments
TCA1116PWR

TCA1116PWR - 16-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments TCA1116PWR is a low-voltage 16-bit I2C and SMBus parallel I/O expander with interrupt and reset functions, operating at up to 400 kHz in a 24-pin TSSOP package. Its 16 configurable ports expand a host controller's digital input and output capacity while preserving a compact serial-bus architecture. The device supports 1.65 V to 5.5 V operation, 5 V-tolerant I/O, and 1.8 V I2C operation. An I/O expander is an interface IC that translates serial I2C commands into parallel digital signals. It sits between a microcontroller or other host controller and external switches, sensors, indicators, or logic inputs. The TCA1116PWR belongs to the I/O expander category, the interface IC category, and the broader semiconductor hierarchy. Its purpose is to reduce the number of GPIO pins required by embedded systems while allowing the added ports to be addressed through the I2C bus. Key features include 16 independently usable I/O ports, 400 kHz serial-bus operation, an active-low open-drain interrupt output, and an active-low reset input. The I/O pins tolerate 5 V signals, while the SDA and SCL inputs remain 5 V tolerant during partial power-down with less than 1 uA of leakage even when VCC is zero. These features allow mixed-voltage interfaces and controlled shutdown behavior in compact embedded systems. The TCA1116PWR is designed for systems in which a host needs more parallel lines than its controller provides. Two programming interfaces can address the expander, and its address inputs support placing multiple devices on one bus. The interrupt output allows the controller to avoid continuous polling when a connected peripheral changes state. Reset provides a defined startup state for the ports and helps simplify firmware initialization across a multi-device system. Typical uses include industrial control modules, building-automation interfaces, sensor aggregators, programmable logic controllers, LED and relay monitoring, test equipment, and embedded human-machine interfaces. In a sensor aggregation circuit, the host can configure input ports, read multiple digital signals, and use the interrupt line to request service only when a monitored event occurs. The TCA1116PWR is particularly useful where board area and host-controller pin count are constrained. When laying out the circuit, connect pull-up resistors to the appropriate I2C supply and keep SDA, SCL, and interrupt traces away from noisy switching nodes. Confirm the device address configuration and reset state in firmware, and account for the open-drain nature of the interrupt output when selecting its pull-up network. This page consolidates the device function, interface limits, package details, practical design guidance, and qualified drop-in comparison information to support faster component selection and PCB implementation.

RFQ צור קשר
TCA3385-FP Telephone Ring Signal Converter | Motorola
TCA3385-FP

TCA3385-FP Telephone Ring Signal Converter | Motorola

The Motorola TCA3385-FP is a telephone ring signal converter integrated circuit offered in a 16-pin SOG package. Its primary function is to support telephone-line ringing interfaces, while the verified distributor information identifies it as a telecom IC and the manufacturer datasheet describes it as a telephone ring signal converter. The available catalog data confirms the MPN, package class, current distributor listing, and a starting price of $0.6525 as of 2026-10-29. A telephone ring signal converter belongs to the interface IC category within the broader semiconductor hierarchy. Telephone equipment must distinguish ringing voltage from normal speech and off-hook signals, often while protecting line-facing circuitry from the higher voltage used during the ringing interval. This device is intended for that signal-conditioning role rather than for general-purpose logic, memory, or power conversion. Its exact electrical limits, timing characteristics, and application topology must be confirmed in the manufacturer datasheet. The verified sources identify TCA3385-FP as a Telecom IC in a 16-SOG package. LCSC lists the component as in stock with a starting price of $0.6525, while DigiKey Marketplace identifies a Rochester Electronics listing and Octopart reports pricing from two distributors. These details make the device available for comparison and sourcing, although they do not establish that every distributor offers identical stock, warranty terms, or production quantities. Typical uses include telephone-line ringing interfaces, analog telephone equipment, and legacy telecom systems in which the circuit receives or conditions a ring signal. The implementation should account for the line voltage, ringing cadence, protection requirements, grounding, and isolation boundaries defined by the telephone interface being supported. The complete pin assignments and application schematic are not present in the supplied verification data, so they should not be inferred from generic 16-pin packages. For new designs, engineers should verify the TCA3385-FP against the original schematic and the latest available manufacturer documentation before layout release. In particular, check maximum voltage, quiescent current, interface timing, exposed or non-exposed pad arrangement, and external component requirements. Distributor snippets alone are not sufficient for safety-critical or high-volume production sign-off. This page combines verified distributor availability, package identification, purchasing information, and application-oriented engineering guidance. It clearly separates confirmed facts from parameters that still require datasheet verification, helping engineers evaluate the TCA3385-FP without mistaking catalog metadata for complete electrical specifications.

RFQ צור קשר
TCA355GXK - Capacitive Touch Proximity Sensor | Infineon
TCA355GXK

TCA355GXK - Capacitive Touch Proximity Sensor | Infineon

Infineon Technologies TCA355GXK is a capacitive touch proximity sensor integrated circuit offered in an 8-pin SOIC package. The verified distributor information identifies the device as an Infineon capacitive touch sensor and provides part data, pricing, availability, pinout diagrams, and datasheet links through authorized distribution listings. Its DSO-8 form factor supports compact proximity-detection designs where a conventional discrete sensor and its associated routing would consume excessive board area. A capacitive proximity switch is a semiconductor device that detects the presence of a nearby conductive object through changes in an electric field. In the product hierarchy, the TCA355GXK is an integrated circuit, a capacitive touch sensor, and a proximity-sensing device. Unlike a mechanical switch, it can detect approach without physical contact, supporting touch-oriented controls, presence detection, and compact user interfaces. The verified package information identifies the TCA355GXK as an 8-SOIC, measuring 0.154 inch or 3.90 mm in width. A public, manufacturer-hosted pinout was not included in the supplied data, so no pin names or pin numbers have been inferred. The package_svg_key is therefore based only on the verified eight-pin SOIC package designation, while the detailed pinout remains null pending confirmation against the manufacturer datasheet. Verified commercial information shows TCA355GXK listings from LCSC beginning at $0.7758, an icDirectory listing at $1.94000 with 9,850 units indicated in stock, and an eBee listing beginning at $2.4325. Prices and inventory are distributor-specific and may change without notice. Consequently, all pricing references in this record are stated as of 2026-10-28. The TCA355GXK is appropriate for engineers evaluating compact capacitive proximity sensing in consumer controls, industrial panels, appliance interfaces, and access-oriented products. Design validation should include electrode geometry, environmental moisture, conductive-object properties, operating distance, and response behavior for the target enclosure. Those application-specific tuning values are not supplied in the verified web data and must be established with the manufacturer datasheet and prototype measurements. This product record combines verified package and distributor information with explicit uncertainty markers for missing electrical characteristics. It also distinguishes the confirmed eight-pin package from unverified pin assignments and avoids treating generic cross-reference search pages as evidence of electrically equivalent drop-in replacements. Engineers should compare the complete manufacturer specification set before committing a PCB footprint or production quantity.

RFQ צור קשר
TCA39306DCURQ1 - Dual I2C/I3C Level Translator 12.5MHz | TI
TCA39306DCURQ1

TCA39306DCURQ1 - Dual I2C/I3C Level Translator 12.5MHz | TI

The Texas Instruments TCA39306DCURQ1 is an automotive-qualified dual bidirectional voltage-level translator compatible with I2C, SMBus, and I3C buses, featuring an enable (EN) input and packaged in an 8-pin VSSOP (DCU) surface-mount package. It supports VREF1 from 0.9V to 3.3V and VREF2 from 1.8V to 5.5V, enabling bidirectional voltage translation between 0.85V and 5V rails without a direction pin, with a maximum data rate of 12.5MHz. A voltage-level translator is an interface IC that allows devices operating at different supply voltages to communicate over the same two-wire or multi-drop bus. In the hierarchy of signal-integrity components, it sits between the I2C buffer/repeater family and general-purpose level shifters, and is classified as a voltage translator within the broader interface IC and communication semiconductor categories. Key features include bidirectional operation without a DIR pin, I3C compatibility with support for open-drain and push-pull signaling, a low ON-state resistance (RON) pass-gate switch architecture that minimizes signal distortion, and an EN input that places both channels in a high-impedance state when disabled. The low RON of the internal switch allows connections to be made with minimal propagation penalty and reduced pull-up loading. Architecturally, the TCA39306 uses a two-reference-rail topology: the pass transistors compare VREF1 and VREF2 so that a low level on either side propagates correctly to the opposite side. This pass-gate approach is faster and lower-power than open-drain FET arrangements, which is what enables 12.5MHz (Fast-mode Plus and I3C-class) operation. Typical applications include automotive body electronics and infotainment I2C bus translation, RTC-to-microcontroller interfaces spanning backup-battery and main-rail domains, industrial sensor modules bridging 3.3V MCUs to 5V peripherals, and I3C sensor hubs. AEC-Q100 qualification makes it suitable for automotive temperature environments. Design tip: select pull-up resistors per the I2C standard-mode (100kHz) and fast-mode (400kHz) maximum/minimum resistance limits shown in the TI datasheet, and tie EN to the lower-voltage domain to guarantee correct default state. This page adds value beyond the datasheet by compiling distributor pricing, drop-in alternatives, comparison tables, and practical design notes in one place.

RFQ צור קשר
TCA39306DDFR - Dual I2C/I3C Bidirectional Level Translator | TI
TCA39306DDFR

TCA39306DDFR - Dual I2C/I3C Bidirectional Level Translator | TI

The Texas Instruments TCA39306DDFR is a 2-bit dual bidirectional voltage-level translator compatible with I2C, SMBus, and I3C (up to 12.5 MHz), operating from a 0.9 V to 3.3 V VREF1 rail and a 1.8 V to 5.5 V VREF2 rail, housed in an 8-pin TSOT-23-8 (DDF) surface-mount package. A voltage-level translator (also called a logic level shifter or voltage translator) is an integrated circuit that allows digital signals referenced to one supply domain to drive inputs in a different supply domain. Within the system hierarchy, level translators sit in the logic and interface IC family, bridging mismatched voltage domains between microcontrollers, sensors, and peripherals. Bidirectional translators such as the TCA39306 are essential for open-drain buses like I2C, where the same two wires (SDA and SCL) carry traffic in both directions. Key features include automatic bidirectional translation without a direction pin, support for Standard-mode (100 kbps), Fast-mode (400 kbps), and Fast-mode Plus (1 Mbps) I2C, plus I3C compatibility at 12.5 MHz, and an enable (EN) input for bus isolation. The low ON-state resistance (RON) of the internal pass-gate switches minimizes signal degradation and bus loading. Technically, the TCA39306 implements the reference-voltage biased switch architecture: VREF1 biases one side of the pass gate and VREF2 the other, so the open-drain pull-up levels define the translated logic levels. This pass-switch topology draws negligible static current and preserves I3C push-pull signaling on the SDA line, which open-drain-only solutions cannot support. Typical applications include mixed-voltage I2C bus segments (for example, a 1.8 V sensor side talking to a 3.3 V or 5 V controller side), SMBus systems in servers and power supplies, and emerging I3C peripherals in mobile and IoT designs. The tiny TSOT-23-8 footprint suits space-constrained board layouts. Design consideration: choose pull-up resistors on both sides appropriately - lower-value pull-ups (for example 1 kOhm to 4.7 kOhm) are needed for Fast-mode Plus and I3C rise-time compliance, while the EN pin can be driven to isolate the bus during reset sequences. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.

RFQ צור קשר
TCA39306DTMR - Dual I2C/SMBus/I3C Bidirectional Level Translator | TI
TCA39306DTMR

TCA39306DTMR - Dual I2C/SMBus/I3C Bidirectional Level Translator | TI

The Texas Instruments TCA39306DTMR is a dual (2-bit) bidirectional voltage-level translator for SDA and SCL lines in mixed-voltage I2C, SMBus, and I3C applications, supporting VREF1 from 0.9V to 3.3V, VREF2 from 1.8V to 5.5V, and translations between 0.85V and 5V, housed in an 8-pin X2SON (1.35mm x 0.8mm) package with tape-and-reel delivery. A voltage-level translator is a logic-family interface IC that bridges digital signals between circuits operating at different supply rails, a member of the broader voltage-translation and logic-translation hierarchy within standard logic ICs. For open-drain buses such as I2C and SMBus, a bidirectional translator is required because data flows both ways on the same line without a direction-control pin; the TCA39306 solves this by using pass-gate switches with integrated pull-up references tied to each side's reference voltage. Key features include standard-mode (100 kbps), fast-mode (400 kbps), and fast-mode-plus (1 Mbps) I2C compatibility, I3C compatibility up to 12.5 MHz, an enable (EN) input for power sequencing and bus isolation, and very low ON-state resistance (RON) of the internal switches, which minimizes signal attenuation and allows external pull-up resistors to remain small. Because there is no direction pin, both channels (SDA and SCL) translate automatically as the bus arbitrates. Technically, the device uses two NMOS pass transistors per channel: when B-side is high, the switch conducts and the A-side tracks it; when A-side is pulled low, the switch passes the low level through. The EN pin must be driven to VREF1 for normal operation and can be grounded to place the bus in high-impedance, useful for hot-swapping and multi-master isolation. Typical applications include mixed-voltage MCU-to-sensor I2C links, server and industrial automation bus translation, and consumer electronics peripheral interfaces where a 1.8V controller must talk to a 3.3V or 5V peripheral. Design consideration: choose pull-up resistors for both rails carefully; smaller pull-ups speed rising edges but increase sink current through the internal switch, so follow the TI TCA39306 EVM User's Guide (SCPU045) guidance on load capacitance and pull-up selection. This page synthesizes distributor pricing context, drop-in alternative analysis, and practical design notes that go beyond the manufacturer datasheet.

RFQ צור קשר
TCA4311ADR - 2.7-5.5V I2C/SMBus Buffer | Texas Instruments
TCA4311ADR

TCA4311ADR - 2.7-5.5V I2C/SMBus Buffer | Texas Instruments

The Texas Instruments TCA4311ADR is a 2-bit bidirectional hot-swappable I2C/SMBus buffer operating from 2.7 V to 5.5 V, supporting bus frequencies up to 400 kHz in an 8-pin SOIC package. It buffers the SDA and SCL lines, increases bus fanout, and uses 1 V precharge on SDA and SCL to reduce corruption during live connections. The device is specified for temperatures from -40 °C to +85 °C. An I2C buffer, also called a bus buffer or bus repeater, is an interface IC placed between two bus segments. It reproduces the SDA and SCL signals in both directions so that bus capacitance, voltage-level differences, and long interconnect sections can be managed more effectively. In the broader hierarchy, the TCA4311ADR belongs to the I2C interface-controller, bus-buffer, interface-IC, and semiconductor categories. The principal features include bidirectional operation on both SDA and SCL, a 2.7 V to 5.5 V operating-power-supply range, and support for I2C/SMBus signaling at up to 400 kHz. Hot-swappable operation addresses systems in which a peripheral may be connected or disconnected while the bus remains active. The 1 V precharge feature helps limit signal corruption during those live insertion and removal events. The TCA4311ADR contains separate buffered paths for SDA and SCL, allowing two-wire bus segments to be isolated with respect to signal propagation and bus loading. Its 8-pin SOIC package is intended for surface-mount assembly. Because the device operates bidirectionally, the SDA and SCL connections must remain correctly terminated and must not introduce additional pull-up paths that exceed the design limits of the bus. Typical uses include hot-pluggable I2C peripherals, bus-isolation and level-translation interfaces, removable sensor modules, card-edge connections, and systems where one bus segment must connect to another without directly loading the entire bus. The 400 kHz operating limit also makes the device appropriate for standard fast-mode I2C equipment, including sensors, EEPROMs, and low-to-medium-rate control peripherals. Designers should account for the hot-swap path, external pull-up resistors, bus capacitance, and the voltage applied to each side of the buffer. Verify signal rise times at the intended bus frequency and ensure that powered-off or disconnected modules cannot back-power either bus segment. The manufacturer pin-description table should be used when assigning tracks and checking pull-up placement. This page combines the manufacturer product information, exact ordering information, supported operating limits, and cross-reference findings into a design-focused overview. It also identifies the limits of available replacement data so engineers can distinguish confirmed package and family options from candidates that still require independent pin-level and timing validation.

RFQ צור קשר
TCA4311D - 2.7-5.5V Hot-Swappable I2C Buffer | TI
TCA4311D

TCA4311D - 2.7-5.5V Hot-Swappable I2C Buffer | TI

The Texas Instruments TCA4311D is a 2-bit bidirectional, hot-swappable I2C/SMBus bus buffer operating from 2.7 V to 5.5 V at up to 400 kHz, and it is packaged in an 8-pin SOIC. It separates a backplane from cards that may be inserted or removed while the bus is operating. According to the Texas Instruments product page, the device connects SDAIN and SCLIN to SDAOUT and SCLOUT when READY is high. An I2C bus buffer is a signal-conditioning interface IC used to isolate two bus segments, extend usable topology, and support controlled card insertion or removal. In the device hierarchy, this function belongs to interface ICs and specifically to bidirectional bus buffers, repeaters, and accelerators. The TCA4311D supports both I2C and SMBus-style two-wire systems, where data and clock lines require buffering rather than unidirectional level translation. Verified headline features include a 2.7 V to 5.5 V operating range, 400 kHz operation, bidirectional signal paths, hot-swappable bus isolation, an enable control, and an open-drain READY output. The READY output indicates that the backplane and card sides are connected together. When EN is high, normal operation resumes; setting EN low places the device into shutdown mode while the I2C bus is idle. The I2C specification cited by Texas Instruments permits up to 400 pF maximum bus capacitance, which can constrain practical bus length. The SMBus specification does not impose that capacitance restriction, although connected-device impedances still limit how quickly the system can meet rise-time and fall-time requirements. Designers should therefore evaluate board capacitance, wiring, pull-ups, and connected-device loading rather than treating buffer insertion as a universal cure for bus-loading problems. Typical uses include server and desktop backplanes, plug-in acquisition modules, industrial control cards, communications equipment, and embedded systems where a card connects to an always-powered bus. The buffer is placed between the backplane pins and card-side pins, preserving independent local behavior on each side. System designers should verify idle-bus shutdown sequencing and interpret READY correctly before enabling the card interface. PCB layout should keep SDA and SCL routing compact, preserve the intended pull-up arrangement on each bus side, and provide the decoupling and grounding required by the manufacturer datasheet. Because the verified material does not expose complete electrical timing, current, capacitance, and pin-level limits in the supplied text, those values remain marked for data completion rather than being inferred. This page combines verified manufacturer and distributor information with design guidance, replacement analysis, and practical procurement context. It also distinguishes true pin-compatible alternatives from packaging-only orderable variants, helping engineers make evidence-based interface decisions.

RFQ צור קשר
TCA4311DR - 2.7-5.5V Hot-Swappable I2C Buffer | TI (Tape & Reel)
TCA4311DR

TCA4311DR - 2.7-5.5V Hot-Swappable I2C Buffer | TI (Tape & Reel)

The Texas Instruments TCA4311DR is a 2-bit bidirectional, hot-swappable I2C/SMBus bus buffer operating from 2.7 V to 5.5 V at up to 400 kHz, and it is packaged in an 8-pin SOIC. It separates a backplane from cards that may be inserted or removed while the bus is operating. According to the Texas Instruments product page, the device connects SDAIN and SCLIN to SDAOUT and SCLOUT when READY is high. An I2C bus buffer is a signal-conditioning interface IC used to isolate two bus segments, extend usable topology, and support controlled card insertion or removal. In the device hierarchy, this function belongs to interface ICs and specifically to bidirectional bus buffers, repeaters, and accelerators. The TCA4311DR supports both I2C and SMBus-style two-wire systems, where data and clock lines require buffering rather than unidirectional level translation. Verified headline features include a 2.7 V to 5.5 V operating range, 400 kHz operation, bidirectional signal paths, hot-swappable bus isolation, an enable control, and an open-drain READY output. The READY output indicates that the backplane and card sides are connected together. When EN is high, normal operation resumes; setting EN low places the device into shutdown mode while the I2C bus is idle. The I2C specification cited by Texas Instruments permits up to 400 pF maximum bus capacitance, which can constrain practical bus length. The SMBus specification does not impose that capacitance restriction, although connected-device impedances still limit how quickly the system can meet rise-time and fall-time requirements. Designers should therefore evaluate board capacitance, wiring, pull-ups, and connected-device loading rather than treating buffer insertion as a universal cure for bus-loading problems. Typical uses include server and desktop backplanes, plug-in acquisition modules, industrial control cards, communications equipment, and embedded systems where a card connects to an always-powered bus. The buffer is placed between the backplane pins and card-side pins, preserving independent local behavior on each side. System designers should verify idle-bus shutdown sequencing and interpret READY correctly before enabling the card interface. PCB layout should keep SDA and SCL routing compact, preserve the intended pull-up arrangement on each bus side, and provide the decoupling and grounding required by the manufacturer datasheet. Because the verified material does not expose complete electrical timing, current, capacitance, and pin-level limits in the supplied text, those values remain marked for data completion rather than being inferred. This page combines verified manufacturer and distributor information with design guidance, replacement analysis, and practical procurement context. It also distinguishes true pin-compatible alternatives from packaging-only orderable variants, helping engineers make evidence-based interface decisions.

RFQ צור קשר
TCA4311DRG4 - 400kHz Hot-Swap I2C Buffer | Texas Instruments
TCA4311DRG4

TCA4311DRG4 - 400kHz Hot-Swap I2C Buffer | Texas Instruments

The Texas Instruments TCA4311DRG4 is a 2-bit bidirectional I2C and SMBus buffer accelerator with a 2.7 V to 5.5 V supply range, 400 kHz bus speed, hot-swap capability, and an 8-pin SOIC package. It supports two-wire bus buffering and allows systems to isolate bus capacitance while improving signal integrity during live insertion or removal. An I2C bus buffer is a bidirectional interface IC that separates a potentially noisy or capacitively loaded bus section from the rest of a two-wire bus. The TCA4311 belongs to the broader I2C interface IC hierarchy, where bus buffers, accelerators, repeaters, and hot-plug controllers support reliable communication between processors, sensors, memory devices, and expansion cards. Its 2-bit architecture provides two buffered channels in a compact surface-mount package. The principal operating characteristics include a 2.7 V minimum supply, 5.5 V maximum supply, and support for 400 kHz I2C operation. The device is intended for hot-plug or hot-swap systems in which a peripheral may be connected to a live bus. Its bidirectional channels allow controller and peripheral traffic to pass through the buffer without changing the underlying open-drain I2C signaling method. The TI TCA4311 product page identifies the device as a 2-bit bidirectional 2.7 V to 5.5 V hot-swappable 400 kHz I2C or SMBus buffer. The manufacturer datasheet explains that I2C limits total bus capacitance to 400 pF, while SMBus does not impose the same capacitance limit. A buffer can therefore divide a long or heavily loaded bus into shorter segments, reducing the capacitive burden seen by a controller while preserving communication across both segments. Typical uses include industrial control modules, hot-pluggable sensor cards, server peripherals, communications equipment, and embedded systems that add or remove equipment while powered. It can also isolate a short, heavily loaded bus segment from a cleaner segment, improving rise-time behavior and reducing the probability that multiple peripheral pull-up networks combine into an excessive effective load. When laying out a board, route the buffered bus sections as controlled transmission-line segments with continuous ground references, place the device close to the bus boundary, and keep both sides of the buffer free of unnecessary stubs. Confirm voltage compatibility, pull-up placement, logic levels, and bus capacitance before implementation because the buffer does not translate voltage levels or replace pull-up resistors. This product page organizes the electrical characteristics, ordering information, drop-in alternatives, comparison parameters, and application guidance around the TCA4311DRG4. It is intended to accelerate component selection, PCB planning, and replacement analysis while keeping each engineering conclusion tied to the manufacturer documentation or an identified cross-reference result.

RFQ צור קשר
TCA5013ZAHR - Smart Card Interface | Texas Instruments
TCA5013ZAHR

TCA5013ZAHR - Smart Card Interface | Texas Instruments

The Texas Instruments TCA5013ZAHR is a smart card interface IC designed for one user card and up to three Secure Access Module (SAM) cards. The device operates from a single supply, generates the required card voltages, and supports ISO 7816-3 and ISO 7816-10 compliant cards for point-of-sale terminals and other secure-access systems. It is packaged in a 48-pin NFBGA (ZAH) package measuring 5 x 5 mm. A smart card interface IC is an interface-controller device that connects a host processor with ISO 7816 smart cards and SAMs. It manages card power, card-clock and card-data signaling, card insertion detection, and the host-side control interface. The TCA5013 is intended for systems requiring one user-card slot plus multiple SAM sockets, allowing payment terminals and access-control products to share a controlled smart-card subsystem. The TCA5013 supports EMV 4.3, ISO 7816-3 and ISO 7816-10 applications. Its single-supply architecture reduces the number of external card-voltage rails required by the host design. The device also includes an I2C control interface and is designed to operate in the industrial temperature range from -40 °C to 85 °C. The 48-terminal NFBGA package provides a compact surface-mount solution for space-constrained terminal hardware. The manufacturer describes the TCA5013 as a feature-rich smartcard interface IC for payment-terminal designs. A typical implementation places the TCA5013 between the host controller and one user-card connector, with additional connectors for as many as three SAM cards. Card insertion and removal can be detected, while the IC controls the card interfaces and generates the card voltages required by the attached cards. The host configures the device through I2C rather than reproducing low-level card timing and power management in application firmware. The TCA5013 is suitable for electronic point-of-sale terminals, payment acceptance equipment, secure-access readers, banking terminals, and other ISO 7816-based systems. The TIDA-00382 reference design provides an implementation pattern for an electronic point-of-sale smart-card subsystem, including a user-card slot and TCA5013-based card detection. It is also useful where multiple secure credentials must be evaluated while maintaining a compact board footprint. PCB implementation requires careful BGA escape routing and power-supply integrity. Place the device close to the user-card and SAM connectors to minimize clock and data trace lengths, route sensitive signals away from switching nodes, and follow the manufacturer’s NFBGA land pattern and assembly guidance. Confirm the card connector pin assignments, pull-up requirements, supply capacitance, and signal-level compatibility before releasing the layout. This product page combines the manufacturer’s smart-card interface specifications with package and ordering details, application guidance, practical PCB considerations, and verified sourcing information. It is intended to help engineers identify the correct TCA5013ZAHR configuration and determine whether its 48-pin NFBGA implementation fits a given secure-card terminal design.

RFQ צור קשר
TCA5405RUGR - 5-Bit 1-Wire I/O Expander | Texas Instruments
TCA5405RUGR

TCA5405RUGR - 5-Bit 1-Wire I/O Expander | Texas Instruments

The Texas Instruments TCA5405RUGR is a 5-bit, self-timed, single-wire output expander with a 1.65 V to 3.6 V supply range, eight pins, and a compact 1.5 mm × 1.5 mm X2QFN RUG package. It is designed to add five controlled outputs to a portable embedded system while requiring only one communication line from the master device. The low-voltage operating range makes the device especially suitable for battery-powered and low-voltage mobile equipment. An output expander is an interface IC that increases the number of controllable outputs available from a microcontroller or other host device. The TCA5405 belongs to the I/O expander hierarchy, where a serial data input causes a group of output channels to change state according to a timing-controlled protocol. Unlike a conventional parallel GPIO port, this device uses a self-timed serial protocol synchronized to an internal clock, reducing the number of host interface signals required. The primary features of the TCA5405RUGR include five output channels, a wide 1.65 V to 3.6 V VCC operating range, a single-wire input, and a self-timed serial data protocol. Its 0.5 mm terminal pitch and 1.5 mm × 1.5 mm body support compact PCB layouts. The manufacturer specifies an operating temperature range of -40°C to +85°C, making the device suitable for industrial and extended-temperature portable applications when the surrounding system meets its electrical and mechanical requirements. In operation, the master device establishes the bit period during a Setup phase. The TCA5405 then uses that timing information to control the five outputs without requiring a separate clock line. This self-timed architecture simplifies connections in space-constrained systems, although the host firmware must generate the required waveform accurately. The protocol timing, output behavior, and electrical limits should be implemented according to the timing diagrams in the Texas Instruments manufacturer datasheet. Typical applications include portable media players, cellular phones, personal digital assistants, and other low-voltage systems in which a host controller needs extra discrete outputs. The device can expand an output-limited controller, support controlled indicators or peripheral signaling, and reduce the pin count required from the host integrated circuit. Its small RUG package is particularly useful when component area and routing density are more important than a large through-hole footprint. A key design consideration is the relationship between supply voltage, output behavior, and the master-generated timing waveform. Keep the single data trace short, provide a stable supply, and validate the Setup and output timing over the full operating-temperature range. Do not assume that a cross-reference device with a similar function is pin-to-pin compatible; confirm package geometry, pin assignment, supply range, and protocol timing before making a replacement. This product summary organizes the TCA5405RUGR function, voltage limits, package details, replacement constraints, comparison points, and application guidance into one engineering reference. It emphasizes the information needed to assess footprint reuse, interface timing, low-voltage operation, and the distinction between a functional substitute and a true drop-in replacement.

RFQ צור קשר
TCA6408PW - 8-Bit I2C I/O Expander | Texas Instruments
TCA6408PW

TCA6408PW - 8-Bit I2C I/O Expander | Texas Instruments

The Texas Instruments TCA6408PW is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PW is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PW uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PW procurement and PCB drop-in decisions efficiently.

RFQ צור קשר
TCA6408PWR - 8-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)
TCA6408PWR

TCA6408PWR - 8-Bit I2C I/O Expander | Texas Instruments (Tape & Reel)

The Texas Instruments TCA6408PWR is an 8-bit I2C and SMBus I/O expander supporting operation from 1.65 V to 5.5 V at up to 400 kHz, housed in a 16-pin TSSOP package. It provides eight general-purpose bidirectional port pins for remote input and output expansion, plus dedicated interrupt, reset, and configuration-register functions. An I/O expander is a bus-interface IC that extends the number of general-purpose inputs and outputs available to a microcontroller or other embedded controller. In the electronic-component hierarchy, the TCA6408PWR is an I2C/SMBus interface controller, a serial interface expander, an interface IC, and ultimately a semiconductor. It reduces the number of host GPIO pins required for switches, indicators, sensors, and other external signals. The device's principal features include eight configurable I/O ports, a two-wire serial interface with a maximum clock frequency of 400 kHz, a broad 1.65 V to 5.5 V operating-voltage range, an interrupt output, a reset input, and configuration registers. These functions allow the host processor to read and control remote digital lines while receiving an interrupt when a relevant input condition occurs. The TCA6408PWR uses addressable I2C control registers to configure port direction and input/output data. This register-based architecture keeps peripheral control separate from the host's limited GPIO resources. According to the Texas Instruments manufacturer datasheet, the device is intended for general-purpose remote I/O expansion across many microcontroller families using the I2C interface with SCL and SDA signaling. Typical applications include industrial control panels, battery-powered portable equipment, communications equipment, programmable logic controllers, and compact embedded systems with multiple discrete controls. The 1.65 V minimum operating voltage supports low-voltage portable systems, while the 5.5 V maximum covers conventional 5 V logic environments. The 400 kHz bus rate permits efficient register access when several compatible devices share the bus. Designers should account for the host's I2C address allocation, pull-up requirements on SDA and SCL, and the electrical characteristics of every attached P-port signal. Firmware should configure each port direction before enabling its outputs, and the reset, configuration, and interrupt functions should be considered when defining startup and event-handling behavior. This product page consolidates the verified distributor information, interface details, same-package replacement candidates, and application-oriented design guidance. It also distinguishes documented parameters from values that still require confirmation from the manufacturer datasheet, helping engineers evaluate TCA6408PWR procurement and PCB drop-in decisions efficiently.

RFQ צור קשר