AT90CAN32-15AT - 32KB AVR CAN MCU, 15MHz | Microchip Technology
MPN: AT90CAN32-15AT ✓ פעילAT90CAN32-15AT סקירה
An automotive microcontroller is a dedicated semiconductor that combines a processor core, nonvolatile program memory, data memory, peripheral controllers, and communication interfaces on one integrated circuit. The AT90CAN32 belongs to the AVR 8-bit RISC family, with the CAN controller placing it within the broader embedded-control and CAN-node product hierarchy. Its architecture combines an 8-bit data bus with an enhanced RISC instruction set designed for efficient control-oriented processing.
Key features include 32 KB of flash program memory, 2 KB of SRAM, 1 KB of EEPROM, 53 general-purpose I/O lines, 32 general-purpose working registers, and 133 powerful instructions. The integrated CAN controller supports CAN 2.0A and CAN 2.0B protocols, allowing the device to communicate with other CAN nodes without an external protocol controller. The 15 MHz operating speed provides a practical balance between processing throughput, power consumption, and system responsiveness.
The AT90CAN32-15AT uses an 8-bit AVR RISC architecture with read-while-write flash capability. Its memory organization supports embedded firmware, configuration data, and nonvolatile calibration or parameter storage. The CAN peripheral, general-purpose I/O, timers, and serial interfaces allow a single controller to supervise a vehicle or industrial subsystem while handling communications and time-critical control tasks.
Typical applications include automotive body-control modules, dashboard and instrument-cluster electronics, diagnostic equipment, industrial CAN gateways, embedded CAN sensors, and service equipment. The 64-pin TQFP package provides access to 53 I/O lines, making the device suitable for systems that need more peripheral connectivity than a smaller microcontroller package can offer.
For PCB design, use the pin-description table in the Microchip Technology datasheet when assigning tracks and decoupling. Provide the specified supply voltage at every power pin, route CAN RX and TX according to the recommended transceiver interface, and include adequate local bypass capacitance to limit supply transients.
This page consolidates the device identity, operating limits, package details, drop-in family alternatives, application guidance, and design notes needed for initial component selection. Firmware migration should still be validated against the manufacturer datasheet, errata, CAN timing requirements, and the exact automotive qualification criteria required by the end application.
חלופות תחליף ישיר עבור AT90CAN32-15AT — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם AT90CAN32-15AT (אותו גורם צורה וטביעת רגל) — שונים ב Package, Flash Memory, CAN Controller, Maximum Clock Frequency, Product Type.
AT90CAN32-15AT1
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←AT90CAN32-16AT
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
AT90CAN32-16AU
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←AT90CAN32-15AU
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
AT90CAN32-15AT דירוגים מרביים ומאפיינים חשמליים
| Product Type | 8-bit automotive AVR RISC microcontroller |
| Maximum Clock Speed | 15 MHz |
| Flash Memory | 32 KB |
| EEPROM Memory | 1 KB |
| SRAM | 2 KB |
| General-Purpose I/O Lines | 53 lines |
| General-Purpose Working Registers | 32 registers |
| Instruction Set | 133 powerful instructions |
| רוחב אפיק נתונים | 8 bit |
| CAN Controller | CAN 2.0A and CAN 2.0B |
| מתח אספקה פעיל | 4.5 V to 5.5 V |
| טווח טמפרטורת פעולה | -40C to +85C |
| מארז | 64-pin TQFP, 14 mm x 14 mm |
| Package Height | 1 mm |
| סוג הרכבה | Surface mount |
| Packing Media | Tape and reel, 1000 units |
| Country of Origin | Taiwan |
| Lifecycle Stage | Active |
מדריך תצורת פינים של AT90CAN32-15AT 1 mm
תצורת פינים עבור AT90CAN32-15AT (מארזת 1 mm). מעגל משולב דיגיטלי זה כולל GPIO, ממשקי תקשורת (UART, SPI, I2C) ופיני מתח. יש לעיין בגיליון הנתונים של היצרן לפונקציות פינים חלופיות ולאפשרויות תצורה. חיוני לתכנון מערכות משובצות ולפריסת PCB.
אין נתוני פריסת פינים מפורטים עבור AT90CAN32-15AT.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
AT90CAN32-15AT מתאים עבור 6 יישוםs: Automotive Body-Control Module, Vehicle Instrument Cluster, Industrial CAN Gateway, Embedded CAN Sensor Node, Automotive Diagnostic Interface, Industrial Service Equipment.
Automotive Body-Control Module
The AT90CAN32-15AT fits an automotive body-control module because its 53 general-purpose I/O lines can connect switches, lamps, solenoids, and diagnostic inputs while the hardware CAN controller manages node communication. At 15 MHz, the AVR core provides deterministic control throughput, and the 32 KB flash holds application firmware with read-while-write capability. The 4.5 V to 5.5 V supply range and -40C to +85C rating suit industrial vehicle environments. A CAN transceiver is still required at the physical network layer, and the PCB must satisfy the vehicle platform’s transient and grounding requirements.
מומלץ
Vehicle Instrument Cluster
An instrument cluster can use the AT90CAN32-15AT for display control, switch scanning, warning indicators, and communication with vehicle CAN nodes. Its 53 I/O lines provide substantial connectivity for display control, indicators, and input devices, while 2 KB SRAM supports temporary display and communication data. The 32 KB flash accommodates compact embedded firmware without an external program-memory device. Designers should partition CAN traffic from display timing and use the manufacturer pin-description table to maintain a clean, reviewable PCB layout.
מומלץ
Industrial CAN Gateway
The AT90CAN32-15AT is suitable for an industrial CAN gateway that converts or aggregates messages between CAN-connected sensors and another embedded interface. Its integrated CAN 2.0A/CAN 2.0B controller reduces system complexity, while the 8-bit AVR core can handle protocol filtering, state management, and diagnostics. With 32 KB flash, 2 KB SRAM, and 1 KB EEPROM, it supports compact gateway firmware and persistent configuration. Keep CAN routing short and controlled, provide local supply bypassing, and validate termination and isolation requirements at the physical bus interface.
מומלץ
Embedded CAN Sensor Node
A compact CAN sensor node can use the AT90CAN32-15AT to acquire data, apply local filtering, and publish measurements over a vehicle or industrial network. The 53 I/O lines permit connection of digital sensors and control outputs, and the 32-bit working-register architecture supports efficient real-time control. Its 15 MHz clock is suitable for protocol servicing and peripheral coordination, while EEPROM can retain calibration values between power cycles. The actual CAN bus driver must be selected for the voltage, isolation, speed, and environmental requirements of the installation.
מומלץ
Automotive Diagnostic Interface
The AT90CAN32-15AT can serve as the controller in a diagnostic interface, executing test sequences and exchanging messages through its integrated CAN controller. The 32 KB flash provides room for a focused diagnostic application, 2 KB SRAM supports buffering, and 53 I/O lines can expose status, service, and communication signals. The -40C to +85C rating is appropriate for many vehicle compartments, although deployment near heat-generating equipment requires thermal review. Firmware should include message timing checks, fault counters, recovery behavior, and bus-off handling appropriate to the vehicle network.
מומלץ
Industrial Service Equipment
For industrial service equipment, the AT90CAN32-15AT can combine CAN communication, local diagnostics, display or indicator control, and configurable I/O in a single controller. Its 32 KB flash and 1 KB EEPROM support embedded application code and persistent service parameters, while the 15 MHz AVR core provides ample throughput for a dedicated CAN endpoint. The 64-pin TQFP package is practical when a moderate number of external lines is needed. Confirm the product’s environmental class, ESD requirements, and CAN bus topology before releasing an industrial service product.
מומלץ
נתוני עזר הנדסיים עבור AT90CAN32-15AT — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | AT90CAN32-15AT1 | AT90CAN32-16AT | AT90CAN32-16AU | AT90CAN32-15AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) |
| Maximum Clock Speed | 15 MHz | 15 MHz | 16 MHz | 16 MHz | 15 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| General-Purpose I/O Lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines |
| CAN Controller | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B |
מבדילים עיקריים
- Integrated CAN communication and extensive I/O in one controller (לעומתAT90CAN64-15AT)
- Exact 15 MHz clock configuration for timing-compatible designs (לעומתAT90CAN32-16AT)
- Identified extended-temperature family option (לעומתAT90CAN32-15AU)
הערות תכנון
Design the supply network for the documented 4.5 V to 5.5 V operating range and place the manufacturer-recommended bypass capacitors close to the AT90CAN32-15AT supply pins. In an automotive installation, include protection against transient and reverse-polarity events at the board boundary rather than relying on the MCU pins alone. Keep the CAN transceiver and protected supply return in the same grounding strategy to prevent bus offsets and false errors.
Assign every signal and power connection from the manufacturer pin-description table before PCB routing. Reserve the 53 general-purpose I/O lines according to reset, programming, peripheral, and alternate-function requirements. Use a short, direct path for oscillator and decoupling connections, maintain a stable ground reference beneath the device, and follow the package drawing for lead orientation and exposed thermal behavior.
Do not assume that a related AT90CAN32 suffix is electrically identical. The -15, -16, AT, AU, and AT1 designators identify ordering combinations that can change clock speed, package code, or temperature grade. Compare each proposed replacement against the original pinout, supply limits, clock requirement, and automotive qualification criteria before approving a drop-in substitution.
Keep the MCU CAN TX and RX routing concise and connect them to a CAN transceiver rather than directly to a physical bus. Route the transceiver-side CANH and CANL pair as a controlled differential pair, apply the network termination specified by the system architecture, and keep switching or high-current paths away from the communication area. Verify signal integrity at the intended bus rate and under worst-case transceiver loading.
The 64-pin TQFP is a surface-mount package with a 1 mm body height, but final thermal performance depends on the PCB copper area, airflow, and nearby heat sources. Follow the manufacturer’s maximum junction-temperature and package guidance, provide an uninterrupted ground plane, and avoid enclosing the device in a sealed enclosure without a thermal path. Estimate junction rise using the actual board construction rather than relying on package size alone.
מידע על תאימות
The product is identified as an automotive-family AT90CAN32 device, but specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information. Confirm these requirements with the manufacturer before environmental or regulatory release.