AT90CAN32-15AT - 32KB AVR CAN MCU, 15MHz | Microchip Technology
部品番号: AT90CAN32-15AT ✓ 生産中AT90CAN32-15AT 概要
An automotive microcontroller is a dedicated semiconductor that combines a processor core, nonvolatile program memory, data memory, peripheral controllers, and communication interfaces on one integrated circuit. The AT90CAN32 belongs to the AVR 8-bit RISC family, with the CAN controller placing it within the broader embedded-control and CAN-node product hierarchy. Its architecture combines an 8-bit data bus with an enhanced RISC instruction set designed for efficient control-oriented processing.
Key features include 32 KB of flash program memory, 2 KB of SRAM, 1 KB of EEPROM, 53 general-purpose I/O lines, 32 general-purpose working registers, and 133 powerful instructions. The integrated CAN controller supports CAN 2.0A and CAN 2.0B protocols, allowing the device to communicate with other CAN nodes without an external protocol controller. The 15 MHz operating speed provides a practical balance between processing throughput, power consumption, and system responsiveness.
The AT90CAN32-15AT uses an 8-bit AVR RISC architecture with read-while-write flash capability. Its memory organization supports embedded firmware, configuration data, and nonvolatile calibration or parameter storage. The CAN peripheral, general-purpose I/O, timers, and serial interfaces allow a single controller to supervise a vehicle or industrial subsystem while handling communications and time-critical control tasks.
Typical applications include automotive body-control modules, dashboard and instrument-cluster electronics, diagnostic equipment, industrial CAN gateways, embedded CAN sensors, and service equipment. The 64-pin TQFP package provides access to 53 I/O lines, making the device suitable for systems that need more peripheral connectivity than a smaller microcontroller package can offer.
For PCB design, use the pin-description table in the Microchip Technology datasheet when assigning tracks and decoupling. Provide the specified supply voltage at every power pin, route CAN RX and TX according to the recommended transceiver interface, and include adequate local bypass capacitance to limit supply transients.
This page consolidates the device identity, operating limits, package details, drop-in family alternatives, application guidance, and design notes needed for initial component selection. Firmware migration should still be validated against the manufacturer datasheet, errata, CAN timing requirements, and the exact automotive qualification criteria required by the end application.
ドロップイン代替品: AT90CAN32-15AT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: AT90CAN32-15AT (同一形状・フットプリント) — 相違点: Package, Flash Memory, CAN Controller, Maximum Clock Frequency, Product Type.
AT90CAN32-15AT1
✅ ドロップイン価格はお問い合わせください
データシートを見る →AT90CAN32-16AT
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AT90CAN32-16AU
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →AT90CAN32-15AU
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AT90CAN32-15AT 最大定格&電気的特性
| Product Type | 8-bit automotive AVR RISC microcontroller |
| Maximum Clock Speed | 15 MHz |
| Flash Memory | 32 KB |
| EEPROM Memory | 1 KB |
| SRAM | 2 KB |
| General-Purpose I/O Lines | 53 lines |
| General-Purpose Working Registers | 32 registers |
| Instruction Set | 133 powerful instructions |
| データバス幅 | 8 bit |
| CAN Controller | CAN 2.0A and CAN 2.0B |
| 動作電源電圧 | 4.5 V to 5.5 V |
| 動作温度範囲 | -40C to +85C |
| パッケージ | 64-pin TQFP, 14 mm x 14 mm |
| Package Height | 1 mm |
| 実装タイプ | Surface mount |
| Packing Media | Tape and reel, 1000 units |
| Country of Origin | Taiwan |
| Lifecycle Stage | Active |
AT90CAN32-15AT 1 mm ピン配置ガイド
AT90CAN32-15AT (1 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: AT90CAN32-15AT.
詳細は データシート をご参照ください。
主な用途
AT90CAN32-15AT の用途: 6 件s: Automotive Body-Control Module, Vehicle Instrument Cluster, Industrial CAN Gateway, Embedded CAN Sensor Node, Automotive Diagnostic Interface, Industrial Service Equipment.
Automotive Body-Control Module
The AT90CAN32-15AT fits an automotive body-control module because its 53 general-purpose I/O lines can connect switches, lamps, solenoids, and diagnostic inputs while the hardware CAN controller manages node communication. At 15 MHz, the AVR core provides deterministic control throughput, and the 32 KB flash holds application firmware with read-while-write capability. The 4.5 V to 5.5 V supply range and -40C to +85C rating suit industrial vehicle environments. A CAN transceiver is still required at the physical network layer, and the PCB must satisfy the vehicle platform’s transient and grounding requirements.
おすすめ
Vehicle Instrument Cluster
An instrument cluster can use the AT90CAN32-15AT for display control, switch scanning, warning indicators, and communication with vehicle CAN nodes. Its 53 I/O lines provide substantial connectivity for display control, indicators, and input devices, while 2 KB SRAM supports temporary display and communication data. The 32 KB flash accommodates compact embedded firmware without an external program-memory device. Designers should partition CAN traffic from display timing and use the manufacturer pin-description table to maintain a clean, reviewable PCB layout.
おすすめ
Industrial CAN Gateway
The AT90CAN32-15AT is suitable for an industrial CAN gateway that converts or aggregates messages between CAN-connected sensors and another embedded interface. Its integrated CAN 2.0A/CAN 2.0B controller reduces system complexity, while the 8-bit AVR core can handle protocol filtering, state management, and diagnostics. With 32 KB flash, 2 KB SRAM, and 1 KB EEPROM, it supports compact gateway firmware and persistent configuration. Keep CAN routing short and controlled, provide local supply bypassing, and validate termination and isolation requirements at the physical bus interface.
おすすめ
Embedded CAN Sensor Node
A compact CAN sensor node can use the AT90CAN32-15AT to acquire data, apply local filtering, and publish measurements over a vehicle or industrial network. The 53 I/O lines permit connection of digital sensors and control outputs, and the 32-bit working-register architecture supports efficient real-time control. Its 15 MHz clock is suitable for protocol servicing and peripheral coordination, while EEPROM can retain calibration values between power cycles. The actual CAN bus driver must be selected for the voltage, isolation, speed, and environmental requirements of the installation.
おすすめ
Automotive Diagnostic Interface
The AT90CAN32-15AT can serve as the controller in a diagnostic interface, executing test sequences and exchanging messages through its integrated CAN controller. The 32 KB flash provides room for a focused diagnostic application, 2 KB SRAM supports buffering, and 53 I/O lines can expose status, service, and communication signals. The -40C to +85C rating is appropriate for many vehicle compartments, although deployment near heat-generating equipment requires thermal review. Firmware should include message timing checks, fault counters, recovery behavior, and bus-off handling appropriate to the vehicle network.
おすすめ
Industrial Service Equipment
For industrial service equipment, the AT90CAN32-15AT can combine CAN communication, local diagnostics, display or indicator control, and configurable I/O in a single controller. Its 32 KB flash and 1 KB EEPROM support embedded application code and persistent service parameters, while the 15 MHz AVR core provides ample throughput for a dedicated CAN endpoint. The 64-pin TQFP package is practical when a moderate number of external lines is needed. Confirm the product’s environmental class, ESD requirements, and CAN bus topology before releasing an industrial service product.
おすすめ
エンジニアリング参考データ: AT90CAN32-15AT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AT90CAN32-15AT1 | AT90CAN32-16AT | AT90CAN32-16AU | AT90CAN32-15AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) | 64-pin TQFP (14 mm x 14 mm) |
| Maximum Clock Speed | 15 MHz | 15 MHz | 16 MHz | 16 MHz | 15 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| General-Purpose I/O Lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines |
| CAN Controller | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B |
主な差別化要因
- Integrated CAN communication and extensive I/O in one controller (vs AT90CAN64-15AT)
- Exact 15 MHz clock configuration for timing-compatible designs (vs AT90CAN32-16AT)
- Identified extended-temperature family option (vs AT90CAN32-15AU)
設計ノート
Design the supply network for the documented 4.5 V to 5.5 V operating range and place the manufacturer-recommended bypass capacitors close to the AT90CAN32-15AT supply pins. In an automotive installation, include protection against transient and reverse-polarity events at the board boundary rather than relying on the MCU pins alone. Keep the CAN transceiver and protected supply return in the same grounding strategy to prevent bus offsets and false errors.
Assign every signal and power connection from the manufacturer pin-description table before PCB routing. Reserve the 53 general-purpose I/O lines according to reset, programming, peripheral, and alternate-function requirements. Use a short, direct path for oscillator and decoupling connections, maintain a stable ground reference beneath the device, and follow the package drawing for lead orientation and exposed thermal behavior.
Do not assume that a related AT90CAN32 suffix is electrically identical. The -15, -16, AT, AU, and AT1 designators identify ordering combinations that can change clock speed, package code, or temperature grade. Compare each proposed replacement against the original pinout, supply limits, clock requirement, and automotive qualification criteria before approving a drop-in substitution.
Keep the MCU CAN TX and RX routing concise and connect them to a CAN transceiver rather than directly to a physical bus. Route the transceiver-side CANH and CANL pair as a controlled differential pair, apply the network termination specified by the system architecture, and keep switching or high-current paths away from the communication area. Verify signal integrity at the intended bus rate and under worst-case transceiver loading.
The 64-pin TQFP is a surface-mount package with a 1 mm body height, but final thermal performance depends on the PCB copper area, airflow, and nearby heat sources. Follow the manufacturer’s maximum junction-temperature and package guidance, provide an uninterrupted ground plane, and avoid enclosing the device in a sealed enclosure without a thermal path. Estimate junction rise using the actual board construction rather than relying on package size alone.
コンプライアンス情報
The product is identified as an automotive-family AT90CAN32 device, but specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information. Confirm these requirements with the manufacturer before environmental or regulatory release.