DG409CY+T - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
MPN: DG409CY+T ✓ פעילDG409CY+T סקירה
A CMOS analog multiplexer is an electronic switching network that connects one common terminal to one of several input terminals. Its hierarchy is analog switch, multiplexer or demultiplexer, interface IC, and integrated circuit. By applying binary select signals, the DG409 routes analog signals among multiple sources while presenting a compact alternative to discrete relays or multiple analog switches. Bidirectional operation allows the same device to work as either a multiplexer or a demultiplexer.
The improved DG409 family provides guaranteed channel matching of 8 ohms maximum and on-resistance flatness of 9 ohms maximum across the specified signal range. Its maximum on-resistance is 100 ohms, while maximum charge injection is 15 pC. These characteristics make the DG409CY+T appropriate for instrumentation where channel-to-channel resistance consistency, signal fidelity, and low switching disturbance are more important than very low resistance alone.
The DG409 family uses CMOS technology and supports two 4:1 switching functions. Low input off-leakage of less than 5 nA at 85 degrees Celsius helps preserve the state of high-impedance nodes between selections. The device can also be used as a demultiplexer because every switch path conducts equally well in either direction. Its dual architecture allows one multiplexed signal and one demultiplexed signal, or two multiplexed functions, to be handled in one package.
Typical uses include routing sensor outputs into an analog-to-digital converter, selecting external test stimuli for automated test equipment, connecting instrumentation channels, and implementing communication-signal path selection. The DG409CY+T is especially appropriate where a compact 16-pin surface-mount package, bidirectional conduction, and controlled channel matching are desired. The industrial-temperature ordering information should be checked against the exact suffix and datasheet ordering table.
PCB design requires care because analog switches inject charge when changing state and can couple transient disturbance into high-impedance nodes. Place the device close to the source and destination signals, keep sensitive traces away from select-line transitions, and provide a quiet ground reference. The SOIC footprint simplifies mixed-signal assembly, but the exposed pad is not applicable to this 16-pin package.
This page combines the manufacturer product information, distributor records, package details, documented switch characteristics, comparison data, and practical PCB guidance. It also distinguishes the tape-and-reel DG409CY+T ordering code from related DG409 variants and identifies which replacement candidates are supported by the available cross-reference records.
חלופות תחליף ישיר עבור DG409CY+T — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DG409CY+T (אותו גורם צורה וטביעת רגל) — שונים ב On-Resistance, Package.
DG409CY+
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DG409CY+T מפרטים
| Switch Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| Number of Channels per Circuit | 4 channels |
| On-Resistance | 100 ohm maximum |
| Channel Matching | 8 ohm maximum |
| On-Resistance Flatness | 9 ohm maximum |
| Charge Injection | 15 pC maximum |
| Input Off-Leakage | Less than 5 nA at 85 C |
| Signal Conduction | Bidirectional |
| Operating Configuration | Multiplexer or demultiplexer |
| Technology | CMOS |
| מארז | 16-pin narrow SOIC |
| סוג הרכבה | Surface mount |
| Order Code Suffix | +T |
| Product Lifecycle | Production |
| סטטוס RoHS | Compliant |
מדריך תצורת פינים של DG409CY+T 16-pin narrow soic
תצורת פינים עבור DG409CY+T (מארזת 16-pin narrow soic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DG409CY+T.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DG409CY+T מתאים עבור 6 יישוםs: Analog Data Acquisition, Automated Test Equipment, Precision Instrumentation, Communication Signal Routing, Battery-Powered Sensor Interface, Mixed-Signal Control Board.
Analog Data Acquisition
The DG409CY+T can select several analog sensor or measurement channels before they reach an ADC. Its two independent 4:1 circuits provide compact routing, while guaranteed channel matching of 8 ohms maximum and on-resistance flatness of 9 ohms maximum help reduce channel-dependent errors. Bidirectional conduction also permits demultiplexing in systems that need source selection and return-path routing. The principal trade-off is a 100 ohm maximum on-resistance, which may create a measurable voltage-divider error with a high-impedance source. A 15 pC maximum charge-injection specification should also be checked against the input impedance, acquisition time, and signal bandwidth.
Automated Test Equipment
The DG409CY+T is well suited to routing test stimuli or measured responses in automated test equipment because two 4:1 switch functions fit into one 16-pin SOIC. The 8 ohm maximum channel matching and 9 ohm maximum resistance flatness improve consistency across selected channels, while bidirectional paths allow the same circuit topology to support multiplexing or demultiplexing. For low-level measurements, the 15 pC maximum charge injection and less than 5 nA input off-leakage at 85 C are important constraints. Keep switched-node traces away from sensitive measurement paths and validate settling behavior for the intended source impedance.
Precision Instrumentation
The DG409CY+T can route sensor, reference, or excitation signals inside precision instrumentation where repeatable channel behavior is important. Guaranteed matching of 8 ohms maximum reduces resistance variation between channels, while the 9 ohm maximum flatness specification controls resistance change across the specified signal range. Bidirectional operation supports flexible panel and system configurations. Designers should account for the 100 ohm maximum on-resistance when calculating divider errors with high source impedances, and should minimize trace capacitance around switched nodes to limit the practical effect of 15 pC maximum charge injection.
Communication Signal Routing
The DG409CY+T can select low-frequency communication or control signals when the circuit requires a compact bidirectional analog router rather than a purely digital mux. Two 4:1 circuits support independent routing paths, and the switch conducts equally well in either direction, allowing one device to handle source selection and return-path selection. The 100 ohm maximum on-resistance is suitable only where the driven load and source impedance produce acceptable attenuation. Engineers should check supply voltage, logic levels, bandwidth, and off-leakage against the line being routed, and keep connector or protection-network transients from exceeding the device's absolute maximum ratings.
Battery-Powered Sensor Interface
The DG409CY+T can reduce the number of discrete analog switches needed in a multi-sensor battery-powered interface. Its dual 4:1 organization permits two compact routing sections, and bidirectional conduction offers flexibility when sensors and host circuitry occasionally exchange roles. Low input off-leakage of less than 5 nA at 85 C helps isolate high-impedance nodes, although actual system leakage depends on surrounding components. Current consumption must be checked against the device's electrical characteristics for the selected supply voltage, while the 100 ohm maximum on-resistance determines whether the switch is suitable for the sensor's source impedance and dynamic range.
Mixed-Signal Control Board
The DG409CY+T is useful in a mixed-signal control board that selects external analog inputs, command voltages, or test points while digital control selects the active path. Its 16-pin narrow SOIC footprint offers a straightforward surface-mount implementation, and the two independent circuits provide more routing flexibility than a single 4:1 switch. Controlled channel matching and flatness are valuable when the selected node affects a precision feedback loop. Keep the multiplexed analog trace away from high-current switching nodes, provide a low-impedance ground reference, and validate whether 15 pC maximum charge injection produces unacceptable transients in high-gain amplifiers.
נתוני עזר הנדסיים עבור DG409CY+T — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DG409CY+ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-pin narrow SOIC |
| Switch Configuration | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits |
| On-Resistance | 100 ohm maximum | 100 ohm maximum |
| Channel Matching | 8 ohm maximum | 8 ohm maximum |
| On-Resistance Flatness | 9 ohm maximum | 9 ohm maximum |
| Charge Injection | 15 pC maximum | 15 pC maximum |
| Signal Conduction | Bidirectional | Bidirectional |
| Technology | CMOS | CMOS |
| Ordering Suffix | +T tape-and-reel order code | Non-T order code |
מבדילים עיקריים
- Controlled channel matching supports repeatable measurements (לעומתDG409CY+)
- Low on-resistance flatness improves signal-range consistency (לעומתDG409CY+)
- Bidirectional dual-multiplexer functionality in a compact package (לעומתDG409CY+)
הערות תכנון
Treat the 15 pC maximum charge injection as a possible source of transient error rather than assuming the switch changes only DC resistance. For a switched node feeding a high-impedance amplifier, estimate the resulting voltage disturbance as charge divided by the effective input and stray capacitance, then allow amplifier recovery time before sampling. Add a selectable input resistor or clamp network when the calculated transient could exceed the downstream signal range.
Route the multiplexed analog node as a short trace directly between the DG409CY+T switch terminal and the receiving circuit. Keep the common terminal and switched terminals away from digital clocks, relay coils, and power-converter switching nodes. Place the device near the connector or sensor interface it serves when possible, because long traces add capacitance and susceptibility to coupled disturbance, which can increase settling time after selection.
Do not choose the DG409CY+T solely from the 4:1 label. Verify the enable polarity, select logic levels, supply range, absolute maximum ratings, and exact package drawing in the manufacturer data sheet. Also confirm that the +T order code corresponds to the required tape-and-reel format. A footprint match alone does not guarantee that two multiplexers have identical control timing or channel assignments.
מידע על תאימות
The available component record identifies DG409CY+T as RoHS compliant. No automotive qualification, REACH, halogen-free, or conflict-minerals declaration was established for the exact order code.