LM2901VNG - Quad 36V Open-Collector Comparator | onsemi
MPN: LM2901VNG ✓ פעילLM2901VNG סקירה
A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. Within the broader semiconductor hierarchy, the LM2901VNG belongs to the comparator and amplifier-IC family. Its four independent channels allow one package to monitor four thresholds or implement four independent protection functions. Unlike an op-amp, each channel uses open-collector output transistors, so an external pull-up resistor is required to establish a high output voltage.
Key electrical characteristics include a maximum supply voltage of 36 V, a single-supply operating range of 3 V to 36 V, an input bias current as high as 0.25 µA, and an open-collector output architecture. The V suffix identifies the higher-performance grade in the LM2901 family, while NG identifies the onsemi 14-pin PDIP package. The through-hole package supports conventional insertion into a PCB and is available in tube packaging according to the manufacturer distribution information.
The comparator architecture supports sensing signals around the supply rails, including low-level and zero-cross detection. Input stages compare a non-inverting input with an inverting input, and the output transistor changes state as the differential input crosses the comparator threshold. Because the outputs are open collector, multiple channels may share a pull-up resistor and form a wired-AND arrangement. The external pull-up must be sized for the logic family, leakage current, switching speed, and fan-out requirement rather than treated as a fixed output impedance.
Typical uses include industrial sensor interfaces, automotive battery and power-system monitoring, consumer threshold detection, memory-device control, and four-channel supervision in industrial automation. The wide 3 V to 36 V single-supply range also permits operation from regulated 5 V and 12 V rails as well as industrial 24 V systems when the applied voltages remain within the rated limits.
PCB design should reserve the correct 14-pin PDIP footprint, provide a continuous ground path, and place the output pull-up resistors close to the comparator pins to limit switching-loop area. Input traces should be kept away from high-current switching nodes and output return currents. Because the LM2901VNG is a through-hole analog device, additional filtering is generally required when sensing noisy sensor nodes rather than relying on comparator hysteresis alone.
This page combines manufacturer and distributor information with application guidance, comparison criteria, and drop-in replacement research. It highlights electrical limits and package compatibility so engineers can distinguish a true pin-compatible substitution from a merely similar quad comparator before releasing a new PCB.
חלופות תחליף ישיר עבור LM2901VNG — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2901VNG (אותו גורם צורה וטביעת רגל) — שונים ב Logic Compatibility, Comparator Type, Mounting Type, Package, Number of Channels.
LM2901NG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901MX/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LM2901N/PB
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901VD
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2901VNG דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | 4 independent general-purpose voltage comparators |
| Number of Channels | 4 channels |
| Single-Supply Operating Range | 3 V to 36 V |
| Dual-Supply Operating Range | ±1.5 V to ±18 V |
| Maximum Supply Voltage | 36 V |
| סוג פלט | Open collector |
| Logic Compatibility | TTL, CMOS, and MOS compatible |
| Maximum Input Bias Current | 0.25 µA |
| מארז | 14-pin PDIP |
| סוג הרכבה | Through hole |
| Packaging | Tube |
תצורת פינים של LM2901VNG
| פין 1 | OUT 1 — Comparator 1 open-collector output |
| פין 2 | OUT 2 — Comparator 2 open-collector output |
| פין 3 | IN 3+ — Comparator 3 non-inverting input |
| פין 4 | IN 3- — Comparator 3 inverting input |
| פין 5 | IN 2+ — Comparator 2 non-inverting input |
| פין 6 | IN 2- — Comparator 2 inverting input |
| פין 7 | V+ — Positive supply voltage |
| פין 8 | GND — Ground reference |
| פין 9 | IN 1+ — Comparator 1 non-inverting input |
| פין 10 | IN 1- — Comparator 1 inverting input |
| פין 11 | IN 4+ — Comparator 4 non-inverting input |
| פין 12 | IN 4- — Comparator 4 inverting input |
| פין 13 | OUT 4 — Comparator 4 open-collector output |
| פין 14 | OUT 3 — Comparator 3 open-collector output |
יישומים טיפוסיים
LM2901VNG מתאים עבור 6 יישוםs: Industrial Sensor Threshold Detection, Automotive Power-System Monitoring, Battery Charger Status Detection, Consumer Level and Limit Detection, Memory and Logic Interface, Power-Supply Rail Supervision.
Industrial Sensor Threshold Detection
The LM2901VNG is appropriate for industrial sensor interfaces that compare a scaled voltage against a reference and produce a logic-level status. Its four independent channels allow one 14-pin PDIP package to monitor four sensor conditions, while its single-supply capability extends to 36 V for 24 V control systems. The open-collector output can sink current into a pull-up network, but input common-mode limits, pull-up voltage, and output-sink capability must remain within the device ratings. Add hysteresis externally where noise or slow sensor transitions could otherwise cause repeated output chatter.
מומלץ
Automotive Power-System Monitoring
The LM2901VNG can supervise several automotive voltage thresholds because it combines four open-collector comparators with a 3 V to 36 V single-supply capability. Channels may monitor a battery-derived signal, charger condition, or protected rail and indicate when each signal crosses a reference. The open-collector architecture permits wired-AND fault reporting to a higher-level controller. Automotive deployment must additionally confirm the exact ordering code’s temperature range, transient immunity, AEC-Q100 status, and operating qualification before production use.
מומלץ
Battery Charger Status Detection
The LM2901VNG is useful in battery-powered equipment where multiple voltage thresholds must be translated into digital status signals. Four channels can compare charger, cell, and system-rail voltages against reference levels derived from the supply. Its wide single-supply range supports 3 V to 36 V systems, and the open-collector outputs can be pulled up to the logic rail used by a charger controller. Designers should verify common-mode input limits, input bias current, and pull-up sizing, especially where the sensing node approaches either supply rail.
מומלץ
Consumer Level and Limit Detection
The LM2901VNG can implement four independent level checks in consumer equipment, such as detecting signal presence, comparing divided-down control voltages, or supervising a supply rail. The general-purpose quad arrangement reduces component count when multiple thresholds require the same supply range and output style. Open-collector outputs are compatible with TTL, CMOS, and MOS logic families, allowing the pull-up rail to match the receiving circuit. Select hysteresis and input filtering according to the source impedance and noise environment rather than relying only on the comparator’s nominal switching performance.
מומלץ
Memory and Logic Interface
The LM2901VNG can support memory and logic-interface functions requiring several comparisons, such as data validity, state-transition, or control-signal qualification. Four independent comparator channels allow individual thresholds to be monitored without sharing internal signal paths, and the open-collector outputs can be combined when the receiving system expects a wired-AND fault indication. Logic compatibility covers TTL, CMOS, and MOS levels, but the external pull-up voltage and sink current must be selected to match the receiving gate. Account for propagation delay when timing relationships depend on multiple channels.
מומלץ
Power-Supply Rail Supervision
The LM2901VNG is applicable to multi-rail power-system supervision because four channels can compare divided-down rail voltages against references and report out-of-range conditions. Its 36 V maximum single-supply rating accommodates many industrial and automotive rails, while each open-collector output provides flexible pull-up selection for the supervisor logic. Keep sensing traces away from switching power nodes, use local filtering where necessary, and verify that every sensed voltage stays inside the common-mode range. For a new design, the newer LM2901V family may offer improved supply-current and response characteristics.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2901VNG — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2901NG | LM2901N | LM2901MX/NOPB | LM2901N/PB | LM2901V |
|---|---|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Comparator Count | 4 | 4 | 4 | 4 | 4 | 4 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
מבדילים עיקריים
- Documented functional and pin-compatible upgrade path (לעומתLM2901MX/NOPB)
- Four monitoring functions in one through-hole package (לעומתLM2901N)
- Wide single-supply operating range (לעומתLM2901N/PB)
הערות תכנון
Route each open-collector output to its pull-up resistor with a short trace and place the resistor close to the comparator output. A long output trace can increase susceptibility to capacitive pickup and slow the rising edge. If multiple outputs share one pull-up node, confirm that the combined leakage and sink-current requirements remain within the resistor and output-stage ratings.
Keep the two inputs of each channel away from switching-power traces and high-current return paths. High source impedance increases input-bias error and makes the switching point sensitive to leakage. When the source impedance is substantial, add a feedback resistor for bias-current compensation and define hysteresis with positive feedback so slow or noisy sensor transitions do not cause repeated output toggling.
Do not treat the open-collector output as a push-pull logic output. Without a pull-up resistor, the output can only sink current and remains in a high-impedance state when the transistor is off. Also verify that the maximum differential input voltage, common-mode input range, and maximum supply voltage are respected. These limits are separate, and satisfying the 36 V supply rating does not by itself permit a 36 V input at every common-mode condition.
The LM2901VNG is intended for low-power signal comparison rather than supplying load current. Use the open-collector stages to sink the pull-up current and keep that current within the output-current and power-dissipation limits. If the comparator monitors a high-voltage rail, divide the voltage with appropriately rated resistors and confirm that their power dissipation and common-mode limits remain acceptable at the maximum operating voltage.
מידע על תאימות
The available manufacturer and distributor descriptions do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with onsemi for the exact ordering code before regulated production use.