LT1131CNW - 5/4 RS232 Transceiver | Analog Devices
MPN: LT1131CNW ✓ פעילLT1131CNW סקירה
An RS-232 transceiver is an interface IC that converts logic-level signals between a digital system and RS-232 differential signaling. The transmitter section converts digital data into RS-232-compatible outputs, while the receiver section converts incoming RS-232 signals into digital logic levels. A 5/4 configuration means five drivers share the package with four receivers, allowing designers to support several communications ports or mixed control and data links.
The LT1131 family is associated with Advanced Low Power 5V RS232 Drivers/Receivers with Small Package Size. The LT1131CNW is offered in a through-hole PDIP package, which can simplify prototyping, inspection, and repair compared with a surface-mount package. The commercial temperature grade and through-hole terminal form make the part relevant to industrial-control, instrumentation, embedded-console, and legacy peripheral designs.
The LT1131CNW is useful where multiple RS-232 channels are required but board area and power consumption must be controlled. Because the device is a multi-channel interface rather than a power semiconductor, no safe-operating-area chart applies. Designers should verify electrical limits, receiver thresholds, driver slew behavior, supply requirements, and pin assignments against the manufacturer datasheet before laying out a new circuit.
Typical uses include RS-232 port expansion, industrial test equipment, serial adapters, programmable controllers, and embedded systems that retain a legacy communication interface. The 28-pin PDIP footprint is also convenient for through-hole industrial control boards where a compact surface-mount package would be inconvenient to assemble.
The most important design step is to preserve the correct pin mapping and bypass-capacitor layout when creating a replacement board. Place required decoupling capacitors close to the supply pins, route each RS-232 driver and receiver according to the datasheet, and allow adequate signal-transition headroom for the selected data rate. This page combines the verified package and product classification with practical selection, replacement, and layout guidance.
חלופות תחליף ישיר עבור LT1131CNW — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
LT1131CN
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LT1131ACN
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
LT1131CNW מפרטים
| Product Type | RS-232 transceiver |
| Driver Count | 5 |
| Receiver Count | 4 |
| Configuration | 5/4 |
| מתח אספקה | 5 V |
| Interface Standard | RS-232 |
| מארז | 28-pin PDIP |
| סוג הרכבה | Through-hole |
| Number of Terminals | 28 |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| Product Category | Drivers, Receivers, Transceivers |
| Manufacturer | Analog Devices |
מדריך תצורת פינים של LT1131CNW rectangular
תצורת פינים עבור LT1131CNW (מארזת rectangular). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור LT1131CNW.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LT1131CNW מתאים עבור 6 יישוםs: Industrial RS-232 Port Expansion, Embedded Console Interface, Serial Test and Measurement Equipment, Legacy Peripheral Adapter, Programmable Instrument Controller, RS-232 Communications Backplane.
Industrial RS-232 Port Expansion
The LT1131CNW fits industrial controllers that need more outbound serial channels than inbound channels. Its five drivers can operate command or control links, while four receivers can monitor response signals, making the 5/4 arrangement useful for legacy automation equipment. The 28-pin PDIP package is straightforward for through-hole industrial boards and facilitates inspection during maintenance. Because the interface is not isolated, the design must include appropriate common-mode protection and grounding at the connector.
מומלץ
Embedded Console Interface
The LT1131CNW is useful in embedded systems that retain a service-console connection alongside other serial peripherals. Five driver outputs can support command, reset, or control lines, and four receiver inputs can collect status signals. Its 5V operation fits legacy control logic, while the through-hole PDIP package simplifies repair and retrofit work. Place the part near the serial connector and include the required supply bypass capacitors to minimize conducted noise.
מומלץ
Serial Test and Measurement Equipment
The LT1131CNW can support legacy RS-232 test equipment that communicates with several instruments or service ports. The 5/4 configuration provides enough outputs for command buses and dedicated control lines while retaining receivers for status and acknowledgment signals. Its through-hole package works well in laboratory and field-instrument designs where reworkability is valuable. For long cables, place protection at the connector and verify that signal levels meet the receiver thresholds over the full voltage range.
מומלץ
Legacy Peripheral Adapter
The LT1131CNW is appropriate for adapter boards that bridge older serial peripherals to a modern controller. Multiple driver and receiver channels allow one board to translate several unidirectional control and data lines, reducing the need for separate interface packages. The 28-pin PDIP footprint is advantageous when the adapter must be assembled with through-hole techniques. Validate connector pin assignments, signal direction, and logic polarity before finalizing the PCB because transceiver count alone does not establish compatibility.
מומלץ
Programmable Instrument Controller
The LT1131CNW can serve in programmable instrument controllers that require several RS-232 outputs for equipment control and four inputs for response monitoring. The device consolidates multiple channels into one package and operates from 5V, matching many legacy measurement platforms. Its through-hole construction is useful when instrument controllers are rebuilt rather than manufactured in high volume. Confirm the driver enable and shutdown states in the datasheet so unused channels are left in a defined condition.
מומלץ
RS-232 Communications Backplane
The LT1131CNW can be used in a communications backplane that carries multiple low-speed control links between equipment modules. Five drivers and four receivers allow asymmetric channel allocation across the board, and the 28-pin PDIP package suits serviceable industrial hardware. To preserve signal quality, route each RS-232 channel as a defined interface, use the ground scheme specified by the manufacturer, and keep external transient devices near connectors rather than beside sensitive circuitry.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LT1131CNW — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
Choose a surface-mount RS-232 transceiver instead when board area, automated assembly, or a smaller footprint is more important than through-hole serviceability. Choose a different 5/4 device when it offers automotive qualification, lower power consumption, higher data rate, improved receiver thresholds, shutdown control, or a package with a verified pin-for-pin match.
No drop-in alternative is presented because the available cross-reference results do not identify a specific part with a verified 28-pin PDIP footprint and confirmed electrical compatibility. Before substituting, compare the complete pinout, supply current, receiver threshold, driver voltage, enable behavior, and temperature range against the manufacturer datasheet. For sourcing support, submit the exact quantity and required package condition through the Request a Quote form.
השוואה עם חלופות
| פרמטר | מוצר זה |
|---|---|
| Brand | Analog Devices |
| Package | 28-pin PDIP |
| Product Type | RS-232 transceiver |
| Driver Count | 5 |
| Receiver Count | 4 |
| Configuration | 5/4 |
| Supply Voltage | 5 V |
| Mounting Type | Through-hole |
| Temperature Grade | Commercial |
| Number of Terminals | 28 |
הערות תכנון
Use the manufacturer package drawing to establish the 28-pin PDIP footprint, row spacing, and drill pattern. Keep the IC away from long unprotected RS-232 traces crossing unrelated logic. Place input and output bypassing exactly as shown in the recommended application circuit, and provide a low-impedance ground return for every interface to reduce noise and common-mode errors.
Plan unused driver and receiver pins according to the datasheet rather than leaving their function unstated. Check whether unused outputs require a defined termination and whether unused receiver inputs may float. Because the complete LT1131CNW pin map is not reproduced in the product listing, use the manufacturer pin-description table when assigning PCB nets and validating the final schematic.
Do not treat a generic 28-pin RS-232 transceiver as automatically compatible. The replacement must match the LT1131CNW channel arrangement, supply requirements, receiver thresholds, driver output levels, enable functions, and pin names. Verify both the IC footprint and every electrical connection; otherwise, an apparently similar package can cause reversed data, inactive outputs, or excessive connector current.
Keep external connector protection close to the RS-232 pins and provide a direct chassis-to-ground strategy appropriate to the equipment. This is especially important when long cables enter an industrial enclosure. Separate RS-232 routing from switching supplies, clocks, and precision analog inputs, and verify the completed board with radiated and conducted emissions testing because interface transients can propagate back into the enclosure.
מידע על תאימות
The verified listings identify a commercial-grade Analog Devices product but do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this commercial RS-232 transceiver classification.