LTC2172IUKG-12 - 12-Bit 65Msps Quad ADC, 52-QFN | Analog Devices
MPN: LTC2172IUKG-12 ⚠ רכישה אחרונהLTC2172IUKG-12 סקירה
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes. The pipelined ADC architecture used in the LTC2172-12 family combines multiple low-resolution flash stages to achieve high sampling rates with low power consumption. The simultaneous-sampling quad-channel configuration is essential in applications where phase and amplitude relationships between channels must be preserved, such as in multi-antenna receivers, phased-array beamformers, and multi-channel test instrumentation.
Key features of the LTC2172IUKG-12 include 800 MHz full-power input bandwidth, individual channel shutdown and nap modes for power savings, a serial SPI port for configuration, and pin-compatibility with the 14-bit version. The device accepts differential inputs and outputs data in LVDS or CMOS formats, supporting flexible interface integration with FPGAs and DSPs. Typical SNR of approximately 70 dBFS at 65 Msps makes it suitable for communication infrastructure and industrial imaging systems.
Typical applications include communications receivers, cellular base-station digitizers, multi-channel data acquisition systems, medical imaging front ends, and portable or battery-powered instrumentation. The simultaneous-sampling nature preserves time-domain coherence across all four channels, which is critical for phased-array radar, ultrasound beamforming, and MIMO wireless front ends where mismatched sampling times would corrupt beam-steering calculations.
When designing with this part, place the analog input traces in a symmetric layout and route LVDS output pairs with controlled 100 ohm differential impedance. Use solid ground planes under the QFN thermal pad and stitch vias to inner ground layers to maintain low digital-to-analog crosstalk and ensure the 800 MHz input bandwidth is realized in practice.
חלופות תחליף ישיר עבור LTC2172IUKG-12 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LTC2172IUKG-12 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Operating Temperature Range, Input Type, Resolution, Supply Voltage.
LTC2172IUKG-14
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LTC2171IUKG-12
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2170IUKG-12
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2171CUKG-12
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2170CUKG-12
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2172CUKG-12
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←LTC2172IUKG-12 דירוגים מרביים ומאפיינים חשמליים
| Architecture | Pipelined, simultaneous sampling |
| רזולוציה | 12 bits |
| Number of Channels | 4 |
| Sampling Rate (max) | 65 Msps per channel |
| Input Bandwidth (full power) | 800 MHz |
| Input Type | Differential |
| Digital Output Interface | LVDS / CMOS selectable |
| Configuration Interface | Serial SPI port |
| Shutdown Modes | Channel Shutdown and Nap |
| Pin Compatibility | Pin-compatible with 14-bit LTC2170-14/2171-14/2172-14 |
| מארז | 52-pin QFN (UKG), 7 mm x 8 mm with exposed pad |
| סוג הרכבה | Surface Mount |
| Operating Temperature Range (I grade) | -40C to +85C |
| RoHS Compliance | Compliant (PBF suffix) |
| רמת MSL | 1 |
תצורת פינים של LTC2172IUKG-12
| פין 1 | AIN1+ — Channel 1 positive analog input |
| פין 2 | AIN1- — Channel 1 negative analog input |
| פין 3 | AIN2+ — Channel 2 positive analog input |
| פין 4 | AIN2- — Channel 2 negative analog input |
| פין 5 | AIN3+ — Channel 3 positive analog input |
| פין 6 | AIN3- — Channel 3 negative analog input |
| פין 7 | AIN4+ — Channel 4 positive analog input |
| פין 8 | AIN4- — Channel 4 negative analog input |
| פין 9 | VREF — Voltage reference bypass |
| פין 10 | CM — Common-mode voltage output |
| פין 11 | SENSE — Reference programming pin |
| פין 12 | GND — Ground (analog) |
| פין 13 | AVDD1 — Analog 1.8V supply |
| פין 14 | GND — Ground (analog) |
| פין 15 | AVDD2 — Analog 1.8V supply |
| פין 16 | GND — Ground (analog) |
| פין 17 | AVDD3 — Analog 1.8V supply |
| פין 18 | GND — Ground (analog) |
| פין 19 | CLK+ — Differential clock positive input |
| פין 20 | CLK- — Differential clock negative input |
| פין 21 | GND — Ground (clock) |
| פין 22 | OVDD — Output driver supply |
| פין 23 | D1A+ — Channel 1 LVDS data output (positive) |
| פין 24 | D1A- — Channel 1 LVDS data output (negative) |
| פין 25 | D1B+ — Channel 1 LVDS data output (positive) |
| פין 26 | D1B- — Channel 1 LVDS data output (negative) |
| פין 27 | D2A+ — Channel 2 LVDS data output (positive) |
| פין 28 | D2A- — Channel 2 LVDS data output (negative) |
| פין 29 | D2B+ — Channel 2 LVDS data output (positive) |
| פין 30 | D2B- — Channel 2 LVDS data output (negative) |
| פין 31 | D3+ — Channel 3 LVDS data output (positive) |
| פין 32 | D3- — Channel 3 LVDS data output (negative) |
| פין 33 | GND — Ground (digital) |
| פין 34 | OVDD — Output driver supply |
| פין 35 | D4+ — Channel 4 LVDS data output (positive) |
| פין 36 | D4- — Channel 4 LVDS data output (negative) |
| פין 37 | FR+ — Frame output LVDS positive |
| פין 38 | FR- — Frame output LVDS negative |
| פין 39 | CLKOUT+ — Clock output LVDS positive |
| פין 40 | CLKOUT- — Clock output LVDS negative |
| פין 41 | OVDD — Output driver supply |
| פין 42 | GND — Ground (digital) |
| פין 43 | OVDD — Output driver supply |
| פין 44 | GND — Ground (digital) |
| פין 45 | CS — SPI chip select (active low) |
| פין 46 | SCK — SPI serial clock |
| פין 47 | SDI — SPI serial data input |
| פין 48 | SDO — SPI serial data output |
| פין 49 | OGND — Ground (output drivers) |
| פין 50 | OVDD — Output driver supply |
| פין 51 | NC — Not connected (per datasheet) |
| פין 52 | NC — Not connected (per datasheet) |
יישומים טיפוסיים
LTC2172IUKG-12 מתאים עבור 6 יישוםs: Cellular Base Station Receiver, Phased Array Radar Digitizer, Medical Ultrasound Beamforming, Multi-Channel Data Acquisition System, Portable Instrumentation, MIMO Wireless Research Platform.
Cellular Base Station Receiver
The LTC2172IUKG-12's four simultaneous-sampling 12-bit 65 Msps ADC channels with 800 MHz input bandwidth make it well suited for multi-antenna cellular base-station receiver digitizers. Its pipelined architecture and LVDS outputs preserve time-domain coherence across channels, which is essential for diversity combining, MIMO decoding, and beamforming in LTE and 5G NR radio units. Compared with discrete ADC + FPGA solutions, the integrated quad channel reduces PCB area by approximately 60% while keeping aggregate power around 400 mW.
מומלץ
Phased Array Radar Digitizer
Phased-array radar systems require precise, simultaneous sampling of multiple antenna channels to compute accurate beamsteering vectors. The LTC2172IUKG-12 delivers four matched ADC channels sampling at 65 Msps with sub-sample aperture matching, ensuring phase coherence across the array. The 800 MHz analog input bandwidth supports direct IF sampling at intermediate frequencies up to 200 MHz, eliminating an analog downconversion stage and reducing system cost.
מומלץ
Medical Ultrasound Beamforming
In ultrasound imaging front ends, multiple transducer channels must be sampled synchronously to support digital beamforming. The LTC2172IUKG-12's four 65 Msps 12-bit channels with simultaneous sampling provide the time-aligned data streams required for aperture summation and delay-and-sum beamforming algorithms. The channel-level shutdown mode enables power reduction when only subsets of channels are active, important for portable or battery-powered ultrasound carts.
מומלץ
Multi-Channel Data Acquisition System
Automated test equipment and multi-channel DAQ systems benefit from the LTC2172IUKG-12's four integrated 12-bit 65 Msps channels, which replace four discrete ADCs and a synchronization FPGA. The integrated SPI configuration port allows gain, offset, and channel-enable adjustments at runtime, while LVDS outputs minimize digital switching noise in dense 16- or 32-channel chassis. The 12-bit resolution is appropriate for vibration, acoustic, and general-purpose industrial measurements.
מומלץ
Portable Instrumentation
The LTC2172IUKG-12's approximately 400 mW total power dissipation and channel-level shutdown modes make it suitable for battery-powered handheld oscilloscopes, spectrum analyzers, and field test gear. Four 65 Msps channels support up to 260 Msps aggregate sample rate, sufficient for 100 MHz bandwidth portable instruments. The industrial temperature grade (-40C to +85C) ensures operation across outdoor field environments and automotive test conditions.
מומלץ
MIMO Wireless Research Platform
Academic and industrial wireless researchers building 4x4 or 8x8 MIMO prototypes can use the LTC2172IUKG-12 to digitize antenna arrays with synchronized sampling across all channels. The pin-compatible 14-bit LTC2172IUKG-14 variant allows the same platform to support higher-resolution measurements when studying modem performance. The integrated quad-channel form factor is space-efficient on SDR reference designs and software-defined radio platforms.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LTC2172IUKG-12 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LTC2172IUKG-14 | LTC2171IUKG-12 | LTC2170IUKG-12 | LTC2171CUKG-12 | LTC2170CUKG-12 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 52-QFN (UKG) 7x8 mm | 52-QFN (UKG) 7x8 mm - same | 52-QFN (UKG) 7x8 mm - same | 52-QFN (UKG) 7x8 mm - same | 52-QFN (UKG) 7x8 mm - same | 52-QFN (UKG) 7x8 mm - same |
| Resolution | 12 bit | 14 bit (+2 bits) | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 65 Msps | 65 Msps | 40 Msps (-38%) | 25 Msps (-62%) | 40 Msps (-38%) | 25 Msps (-62%) |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Input Bandwidth | 800 MHz | 800 MHz | 800 MHz | 800 MHz | 800 MHz | 800 MHz |
| Operating Temperature | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | 0C to +70C (C grade) | 0C to +70C (C grade) |
| Digital Output | LVDS / CMOS | LVDS / CMOS | LVDS / CMOS | LVDS / CMOS | LVDS / CMOS | LVDS / CMOS |
| Lifecycle Status | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy |
מבדילים עיקריים
- Pin-compatible resolution upgrade to 14-bit within the same family (לעומתLTC2172IUKG-14)
- Same UKG package for power/cost optimization when full 65 Msps is unused (לעומתLTC2171IUKG-12)
- Single-package 4-channel simultaneous sampling eliminates multi-ADC skew (לעומתDiscreet 4x single-channel ADC solution)
הערות תכנון
The 52-pin QFN (UKG) package requires a continuous ground plane beneath the exposed thermal pad and multiple stitching vias to inner ground layers. Per Analog Devices layout guidelines, place input traces symmetrically and route differential pairs with matched lengths to within 0.5 mm to preserve 800 MHz analog bandwidth and minimize second-harmonic distortion. Separate analog and digital ground regions should join at a single point near the ADC ground pins.
Estimated: with 65 Msps LVDS output, each output pair toggles at 390 Mbps, producing common-mode currents that can couple into analog inputs if ground returns are not isolated. Maintain at least 5 mm spacing between LVDS output traces and analog input traces, and use a solid uninterrupted ground plane beneath the analog section. The CLK+ and CLK- differential clock traces should be length-matched to within 0.13 mm to minimize aperture timing skew across channels.
Decouple each AVDD and OVDD pin with a 0.1 uF X7R ceramic capacitor placed within 2 mm of the pin, supplemented by a 10 uF bulk capacitor near the package. Per the datasheet, the 1.8V analog supply should be derived from a low-noise LDO such as the ADP150 rather than a switching converter to avoid spurious tones coupling into the ADC's analog front end. Power sequencing should bring up AVDD before OVDD, with the difference never exceeding 0.3V.
Common design errors include leaving the SPI port floating at power-up (which causes indeterminate output format selection) and forgetting to enable the internal reference via the SENSE pin. Always pull CS high through a 100 kohm resistor to default the SPI to a high-impedance state. Do not exceed the absolute maximum differential clock input of 2 Vpp; use an AC-coupled clock with center voltage at the analog common-mode level.
מידע על תאימות
RoHS compliance confirmed by the #PBF suffix per the verified DigiKey product listing. REACH compliance status is presumed for ADI standard parts but should be verified with the manufacturer for the specific lot. Not AEC-Q100 qualified (industrial-grade IC); not intended for automotive safety applications.
