MAX323ESA+ - Dual 16V SPST Analog Switch | Maxim
MPN: MAX323ESA+ ✓ פעילMAX323ESA+ סקירה
An analog switch is a semiconductor device that routes electrical signals between terminals under digital control. The MAX323ESA+ belongs to the analog-switch hierarchy, where its two normally open SPST channels provide independent, unidirectional or bidirectional signal connections. In system terms, it sits between external analog circuitry and a controller, allowing a compact processor to select among sensors, test points, or signal paths.
The MAX323 family provides two precision SPST switches in a single package. Both channels are normally open, meaning each path is disconnected until its control input commands closure. Operation from 2.7 V to 16 V covers 3.3 V and 5 V control systems as well as higher single-supply rails. The 5 microwatt low-power characteristic is particularly useful when leakage or standby consumption is more important than minimizing on-resistance.
The device's precision switching architecture is intended for moderate-impedance signal paths rather than power switching. A 175-ohm on-resistance can limit voltage drops when carrying source currents, but it is substantially higher than a power MOSFET or relay. Engineers should therefore account for the resistance in the complete signal path and avoid using the switch as a general-purpose high-current load driver. The low-power design also makes the device appropriate for battery-powered measurement and communication equipment.
Typical uses include analog test-point selection, sensor disconnect, sample-and-hold isolation, battery-powered instrumentation, and routing signals between a data-acquisition circuit and an analog front end. The MAX323 family is also identified for DAC and ADC applications, audio and video switching, communication systems, guidance and control systems, and heads-up displays where low standby power is valuable.
The principal design consideration is control compatibility and signal integrity. Keep analog traces short, use a continuous ground reference, and ensure that control transitions do not inject unacceptable disturbance into sensitive measured signals. The normally open architecture also means the switch remains disconnected during power-down, which can be advantageous for isolation but may differ from a normally closed design.
This page combines the manufacturer's family specifications, verified package and pricing references, application guidance, and drop-in comparison information to support component selection, PCB planning, and replacement analysis beyond the basic datasheet feature list.
חלופות תחליף ישיר עבור MAX323ESA+ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
MAX323ESA
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX323CUA+
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX324ESA+
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX325ESA+
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX323ESA+T
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX323ESA+ דירוגים מרביים ומאפיינים חשמליים
| Product Type | Precision analog switch |
| Number of Channels | 2 channels |
| Switch Configuration | Dual SPST, normally open (NO) |
| Supply Voltage Range | 2.7 V to 16 V |
| On-Resistance | 175 ohms |
| Power Consumption | 5 microwatts |
| מארז | 8-pin NSOIC |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
| Number of Switches | 2 switches |
| Switch Type | Single-pole, single-throw (SPST) |
| Default State | Normally open |
| Supply Type | Single supply |
| Signal Configuration | 1:1 |
| Manufacturer | Maxim Integrated |
| סטטוס מחזור חיים | Production |
מדריך תצורת פינים של MAX323ESA+ 8-pin nsoic
תצורת פינים עבור MAX323ESA+ (מארזת 8-pin nsoic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MAX323ESA+.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MAX323ESA+ מתאים עבור 6 יישוםs: Battery-Powered Data Acquisition, Precision Analog Signal Routing, ADC and DAC Signal Isolation, Audio and Video Signal Switching, Industrial Test and Measurement, Communication and Guidance Systems.
Battery-Powered Data Acquisition
The MAX323ESA+ fits battery-powered data-acquisition systems because its dual SPST channels operate from 2.7 V to 16 V while consuming approximately 5 microwatts. Place the device between the analog input network and the acquisition circuitry to disconnect or reconnect selected sensors without leaving an unintended signal path connected. The normally open state is particularly useful when standby current is critical. Because the switch has a listed on-resistance of 175 ohms, engineers should verify that the resulting voltage drop and input-loading effects remain acceptable for the selected sensor and amplifier.
מומלץ
Precision Analog Signal Routing
The MAX323ESA+ is suitable for precision analog signal routing where two independent paths must be selected under digital control. Its two normally open SPST channels can connect sensor outputs, test points, or amplifier inputs one at a time. The 2.7 V minimum supply supports 3.3 V systems, while the 16 V maximum provides additional flexibility for higher-voltage single-supply designs. The 175-ohm on-resistance must be included in the source-impedance and error-budget calculation, especially when driving a high-impedance downstream amplifier.
מומלץ
ADC and DAC Signal Isolation
The MAX323ESA+ can isolate ADC or DAC signal paths in mixed-signal equipment by separating a converter input or output until commanded. This can prevent unused channels from loading a sensitive analog node and can support controlled connection sequences during measurement cycles. Its low 5 microwatt consumption is valuable in portable instruments, while the normally open behavior provides a defined disconnected state. Confirm that the 175-ohm resistance and switch leakage satisfy the converter’s input-impedance, settling-time, and acquisition-noise requirements before finalizing the signal chain.
מומלץ
Audio and Video Signal Switching
The MAX323ESA+ can implement low-power signal routing in audio and video equipment where the switched impedance is acceptable. The two independent channels may select between sources, isolate an amplifier input, or disconnect a muted section of a circuit. Operation from a single 5 V rail is convenient for conventional consumer electronics, and the manufacturer notes TTL compatibility at 5 V. For high-fidelity audio paths, verify noise, off-state leakage, and channel behavior against the signal amplitude and impedance before using the switch in a critical reference path.
מומלץ
Industrial Test and Measurement
The MAX323ESA+ is appropriate for test-point multiplexing, probe isolation, and controlled connection of external measurement nodes in industrial instrumentation. Two normally open channels can isolate the device under test until a measurement sequence commands connection, reducing loading from unused fixtures. The 2.7 V to 16 V operating range accommodates several single-supply system rails. Designers should account for the 175-ohm insertion resistance, control settling time, and possible charge injection when establishing the accuracy budget for high-impedance or high-speed measurements.
מומלץ
Communication and Guidance Systems
The MAX323ESA+ can support signal selection or isolation in compact communication and guidance systems where board area and standby power are constrained. Its 8-pin NSOIC package leaves routing space for the two analog channels, while the 2.7 V to 16 V supply range supports common embedded rails. The switch should be used for low-current signal paths rather than power loads. Validate control thresholds, off-state leakage, and transient behavior in the final system, particularly when switching signals near sensitive communication or sensing thresholds.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX323ESA+ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX323ESA | MAX323CUA+ | MAX324ESA+ | MAX325ESA+ | MAX323ESA+T |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC | 8-pin NSOIC |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Switch Configuration | Dual SPST, normally open | Dual SPST, normally open | Dual SPST, normally open | Dual SPST, normally closed | One normally open and one normally closed | Dual SPST, normally open |
מבדילים עיקריים
- Provides two independent normally open channels (לעומתMAX325ESA+)
- Supports the same single-supply voltage class as the MAX324 family (לעומתMAX324ESA+)
- Offers low 5 microwatt power consumption for portable routing (לעומתMAX323CUA+)
הערות תכנון
Do not treat the MAX323ESA+ as a power switch. Its listed on-resistance of 175 ohms can produce substantial voltage drop when carrying useful current, and the 2.7 V to 16 V rating describes the supply rather than a high-current switching capability. Use a MOSFET, relay, or other power stage for load current, and keep the analog switch in the signal path.
Include the 175-ohm on-resistance when calculating divider ratios, source impedance, gain, and ADC acquisition settling. A high-impedance amplifier or converter input may be affected more by leakage and charge injection than by the nominal on-resistance. Verify the complete settling time and signal error against the measurement bandwidth rather than relying only on the switch’s stated resistance.
Place the MAX323ESA+ close to the controlled analog nodes and return the switched signal over a continuous ground reference. Keep the NSOIC footprint, copper clearance, and pin assignment consistent with the manufacturer package drawing. If the device isolates a sensitive sensor, provide a defined ground around the switched interface and avoid routing high-current return paths beneath analog traces.
The approximately 5 microwatt power consumption is appropriate for low-power signal routing, but total standby demand still includes leakage and any control logic. Check the control-driver state during shutdown so the logic does not hold the analog nodes in an unintended condition. For battery designs, calculate worst-case leakage over temperature rather than relying only on the nominal low-power figure.
מידע על תאימות
The manufacturer family documentation identifies the MAX323 as a production device, but no specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified for the exact MAX323ESA+ ordering code. AEC-Q100 is therefore treated as not applicable rather than qualified.