NE5532APSR vs TL072CP तुलना

विस्तृत दोनों ओर की तुलना NE5532APSR द्वारा Texas Instruments और TL072CP द्वारा Texas Instruments. मुख्य विशेषताओं, इलेक्ट्रिकल पैरामीटर, पैकेजिंग, चक्र स्थिति, मूल्यांकन और उपलब्धता को तुलना करके अपनी डिजाइन की आवश्यकताओं के लिए सबसे अच्छा घटक निर्धारित करें。

Texas Instruments
NE5532APSR NE5532APSR - Dual Low-Noise Op Amp | Texas Instruments

NE5532APSR - Dual Low-Noise Op Amp | Texas Instruments

NE5532APSR ✓ सक्रिय
Texas Instruments
TL072CP TL072CP - Dual JFET-Input Low-Noise Op Amp, 8-PDIP | Texas Instruments

TL072CP - Dual JFET-Input Low-Noise Op Amp, 8-PDIP | Texas Instruments

TL072CP ✓ सक्रिय

विशेषता तुलना

पैरामीटर NE5532APSR TL072CP
ब्रांड Texas Instruments Texas Instruments
श्रेणी Amplifier ICs Amplifier ICs
लाइफसाइकिल स्थिति सक्रिय सक्रिय
Number of Amplifiers 2 circuits —
Supply Voltage Range ±5 V to ±15 V —
Equivalent Input Noise Voltage 5 nV/√Hz typical at 1 kHz —
Unity-Gain Bandwidth 10 MHz typical —
Common-Mode Rejection Ratio 100 dB typical —
Slew Rate 9 V/µs typical 13 V/µs (typical)
Input Bias Current 1 µA typical 30 pA (typical)
High DC Voltage Gain 100 V/mV typical —
ऑपरेटिंग तापमान रेंज 0°C to 70°C 0°C to +70°C (C grade)
Package Type 8-pin SOIC —
पिन की संख्या 8 pins —
Compensation Internally compensated for unity-gain operation —
Output Short-Circuit Protection Included Yes
Input Protection Diodes Included —
Output Drive Capability High —
Maximum-Output-Swing Bandwidth High —
RoHS स्थिति [DATA_NEEDED: RoHS status] Compliant
REACH Status [DATA_NEEDED: REACH status] —
AEC-Q100 Qualification [DATA_NEEDED: AEC-Q100 qualification status] —
Manufacturer — Texas Instruments
Part Status — Active
Amplifier Type — JFET-Input Operational Amplifier
Number of Circuits — 2 (Dual)
Gain Bandwidth Product — 3 MHz (typical)
Input Offset Voltage — 3 mV (typical, C grade)
Input Noise Voltage Density — 18 nV/√Hz (typical at 1 kHz)
Total Harmonic Distortion — 0.003% (typical)
Supply Voltage Range (Dual) — ±3.5 V to ±18 V
Supply Voltage Range (Single) — 7 V to 36 V
पैकेज / केस — 8-PDIP (Plastic DIP, through-hole)
माउंटिंग प्रकार — Through Hole
पिन काउंट — 8
Internal Frequency Compensation — Yes
Latch-up Free Operation — Yes

डेटाशीट और संसाधन

सभी उत्पादों को देखें BOM बनाएं कीट की अनुरोध