LM2901DR2G - Quad Open-Collector Comparator | onsemi
MPN: LM2901DR2G ✓ सक्रियLM2901DR2G अवलोकन
A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level output indicating which input is higher. Within the broader semiconductor hierarchy, the LM2901 belongs to the comparator family, which sits alongside amplifiers, voltage references, and other analog signal-conditioning ICs. The LM2901 is particularly useful when a system must translate an analog threshold crossing into a digital event for control logic, memory, monitoring, or protection circuitry.
The principal features of the LM2901DR2G include four differential comparator channels, a 3 V to 36 V single-supply operating range, an open-collector output architecture, and compatibility with CMOS and TTL loads. Open-collector outputs permit the output stage to be pulled up to the voltage required by the receiving logic. Designers can therefore select the pull-up voltage independently of the comparator supply, provided it remains within the device's applicable operating limits.
The quad arrangement consolidates four comparison functions into one 14-SOIC package. This can reduce component count and board area in designs requiring multiple threshold decisions, such as battery monitoring, window comparison, signal crossing detection, and industrial control inputs. The open-collector architecture is also useful when several outputs must share a common bus or when an external pull-up defines the logic-high level. External pull-up resistors and output-rise-time analysis remain essential design considerations.
Typical uses include automotive battery and power-system monitoring, industrial sensor interfaces, consumer threshold detection, memory-control logic, and general industrial control systems. The -40°C to +105°C operating range supports applications across wide environmental conditions, while the 36 V upper supply limit accommodates higher-voltage industrial and automotive rails. Designers should verify input common-mode limits, output pull-up requirements, and input-current behavior against the manufacturer datasheet for the exact operating conditions.
When laying out an LM2901DR2G circuit, place pull-up resistors close to the open-collector outputs and keep sensitive threshold networks away from switching nodes and high-current return paths. Because the device is intended for level detection and low-level sensing, input filtering, hysteresis, and stable reference generation often matter more than high-speed signal fidelity. The component should be selected only after checking the complete datasheet limits for supply voltage, input common-mode range, output current, and electrical characteristics.
This page combines the exact LM2901DR2G configuration with same-package alternatives, application-specific engineering guidance, a parameter comparison table, and practical layout considerations. These details help buyers distinguish the 14-SOIC part from other LM2901 order codes and assess whether it is appropriate for a new industrial, automotive, or consumer circuit without changing the PCB footprint.
के लिए ड्रॉप-इन विकल्प LM2901DR2G — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2901DR2G (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Comparator Type, Package, Input Bias Current, Output Type, Input Offset Voltage.
LM2901DR2
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2901DRG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM2901DG4
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2901DR2
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2901QDRG4Q1
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM2901DR2G Maximum Ratings और Electrical Characteristics
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| ऑपरेटिंग तापमान रेंज | -40°C to +105°C |
| आउटपुट प्रकार | Open collector |
| Logic Compatibility | CMOS and TTL |
| पैकेज | 14-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Automotive-Grade Variant | NCV2901 family variant identified by onsemi |
LM2901DR2G 14-pin soic पिन कॉन्फ़िगरेशन गाइड
LM2901DR2G (14-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LM2901DR2G.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LM2901DR2G के लिए उपयुक्त है 6 अनुप्रयोगs: Automotive Battery Threshold Monitoring, Industrial Sensor Limit Detection, Power-Supply Fault Signaling, Consumer Level and Range Detection, Memory and Control Logic, Window Comparator and Signal Crossing Detection.
Automotive Battery Threshold Monitoring
The LM2901DR2G is well suited to automotive threshold-detection stages because four comparison channels operate from 3 V to 36 V within a -40°C to +105°C temperature range. Each channel can compare a divided battery signal with a reference and use its open-collector output to request an alert, inhibit a charger, or change an operating mode. Dividing the battery voltage protects the input range and allows multiple thresholds to be checked with only one IC. The open-collector output can also be pulled up to the vehicle logic supply, although the pull-up voltage must satisfy the device limits. For a production design, add transient protection at the battery input, verify the input common-mode range under cranking and load-dump conditions, and confirm automotive qualification against the selected order code.
अनुशंसित
Industrial Sensor Limit Detection
The LM2901DR2G can convert analog sensor conditions into logic events for industrial controllers. Its four independent channels reduce component count when monitoring temperature, pressure, level, or current thresholds, while the 3 V to 36 V supply range supports control systems operating above the lowest logic voltages. Each open-collector output can drive an isolated relay driver, PLC input, or fault line with a suitable pull-up resistor. The device's -40°C to +105°C range covers many industrial environments, but enclosure temperature and sensor accuracy still determine overall fault-detection performance. Engineers should add hysteresis to avoid chatter near a threshold, protect sensor inputs from transients, and verify input bias current, common-mode range, and output sink current before finalizing the interface network.
अनुशंसित
Power-Supply Fault Signaling
The LM2901DR2G is useful for monitoring multiple power rails or input thresholds in power-management equipment. Four comparators can evaluate divided feedback signals against stable references and produce open-collector fault outputs when a rail leaves its permitted range. The 3 V to 36 V operating capability suits systems with a wider input range than ordinary low-voltage logic ICs, while the four-channel package can consolidate overvoltage, undervoltage, sequencing, and enable checks. The design trade-off is that a linear regulator dissipates the difference between input and output voltage, so comparator current should remain modest where continuous monitoring is required. Pull-up resistors should be scaled to balance fault signaling speed with supply-current consumption, and every monitored input must remain inside the comparator's specified common-mode range.
अनुशंसित
Consumer Level and Range Detection
The LM2901DR2G supports compact consumer products that must identify when an analog signal enters or leaves a permitted range. Its four channels can monitor battery level, audio or sensor thresholds, charging conditions, or a divided system signal without requiring four separate packages. The open-collector outputs provide simple wired logic for a microcontroller or system controller, and their CMOS and TTL compatibility supports common digital input arrangements. In battery-powered equipment, however, continuous divider and pull-up currents can dominate standby consumption, so resistor values should be optimized without allowing excessive output rise time. Add positive feedback for hysteresis where the sensed signal has noise or slow transitions, and confirm that the chosen order code satisfies the product's environmental and component-qualification requirements.
अनुशंसित
Memory and Control Logic
The LM2901DR2G can implement simple memory-control and qualification functions where several analog or digital conditions must be resolved before a system changes state. Four open-collector channels may monitor voltage thresholds, acknowledge lines, or timing-derived control signals while operating from the same broad 3 V to 36 V supply range. Open-collector outputs are useful when a wired logic function is needed, but designers must account for the pull-up resistor's rise time and ensure that only one output actively sinks current when a wired-AND node is used. For reliable logic behavior, use clean pull-up connections, maintain adequate logic-level voltage margins, and verify propagation delay and input offset requirements against the timing budget. The onsemi datasheet should be used for the final pin assignments and electrical limits.
अनुशंसित
Window Comparator and Signal Crossing Detection
The LM2901DR2G can implement upper and lower window checks by pairing two comparison channels around a common reference. This arrangement is useful for battery, signal-strength, temperature, or supply-rail monitoring where the system must distinguish an in-range condition from both under-range and over-range faults. Its four channels allow two window functions in one package, reducing board area while maintaining open-collector fault outputs. The principal design challenge is reference accuracy: errors in the reference or resistor divider can shift the actual trip points. Use stable reference and feedback components, add hysteresis to prevent repeated output transitions, and keep the sensing node within the input common-mode limits across the full 3 V to 36 V operating range and -40°C to +105°C temperature span.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM2901DR2G — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM2901DR2 | LM2901DRG4 | LM2901DG4 | LM2901DR | LM2901QDRG4Q1 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Product Type | Quad differential comparator | Quad differential comparator | LM2901 family comparator | LM2901 family comparator | Quad differential comparator | LM2901 family comparator |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Primary Application | Level detection and low-level sensing | Level detection and low-level sensing | General-purpose comparison | General-purpose comparison | General-purpose comparison | Automotive comparison |
मुख्य विशेषताएँ
- Four independent threshold-detection channels in one package (बनामLM2901DR)
- Wide single-supply operating range (बनामLM2901DRG4)
- Open-collector outputs support flexible logic interfacing (बनामLM2901QDRG4Q1)
- Wide environmental operating range (बनामLM2901DG4)
डिज़ाइन नोट्स
Place each open-collector pull-up resistor close to the associated LM2901DR2G output so that the physical loop between the device and receiver is minimized. This reduces susceptibility to capacitive coupling and keeps the logic transition path short. Route threshold-sensing traces away from inductors, switching nodes, and high-current return paths. When a fault output crosses a substantial distance, use a driver or differential interface rather than relying on a weak pull-up signal.
Do not treat an open-collector output as a push-pull logic output. A pull-up resistor is required to establish the high state, and its value determines both the logic rise time and the maximum sink current. Adding hysteresis with positive feedback is recommended when the compared signal contains noise or changes slowly near the threshold. The reference network and input divider should also avoid levels outside the device's specified common-mode range.
Estimated: a 10 kΩ pull-up connected to 5 V can source approximately 0.5 mA when the output is low, based on Ohm's law using 5 V and 10 kΩ inputs. This estimate illustrates the trade-off between low pull-up current and output rise time; the final value must also remain within the LM2901DR2G sink-current and receiver-input requirements. The manufacturer datasheet controls the allowable operating and electrical limits.
अनुपालन जानकारी
The onsemi family is described as available in an automotive-grade NCV2901 variant, but the compliance status of the exact LM2901DR2G order code requires confirmation from its current manufacturer product documentation.