LM2901DR2G - Quad Open-Collector Comparator | onsemi
MPN: LM2901DR2G ✓ 啟用中LM2901DR2G 概覽
A comparator is an analog integrated circuit that evaluates two input voltages and produces a logic-level output indicating which input is higher. Within the broader semiconductor hierarchy, the LM2901 belongs to the comparator family, which sits alongside amplifiers, voltage references, and other analog signal-conditioning ICs. The LM2901 is particularly useful when a system must translate an analog threshold crossing into a digital event for control logic, memory, monitoring, or protection circuitry.
The principal features of the LM2901DR2G include four differential comparator channels, a 3 V to 36 V single-supply operating range, an open-collector output architecture, and compatibility with CMOS and TTL loads. Open-collector outputs permit the output stage to be pulled up to the voltage required by the receiving logic. Designers can therefore select the pull-up voltage independently of the comparator supply, provided it remains within the device's applicable operating limits.
The quad arrangement consolidates four comparison functions into one 14-SOIC package. This can reduce component count and board area in designs requiring multiple threshold decisions, such as battery monitoring, window comparison, signal crossing detection, and industrial control inputs. The open-collector architecture is also useful when several outputs must share a common bus or when an external pull-up defines the logic-high level. External pull-up resistors and output-rise-time analysis remain essential design considerations.
Typical uses include automotive battery and power-system monitoring, industrial sensor interfaces, consumer threshold detection, memory-control logic, and general industrial control systems. The -40°C to +105°C operating range supports applications across wide environmental conditions, while the 36 V upper supply limit accommodates higher-voltage industrial and automotive rails. Designers should verify input common-mode limits, output pull-up requirements, and input-current behavior against the manufacturer datasheet for the exact operating conditions.
When laying out an LM2901DR2G circuit, place pull-up resistors close to the open-collector outputs and keep sensitive threshold networks away from switching nodes and high-current return paths. Because the device is intended for level detection and low-level sensing, input filtering, hysteresis, and stable reference generation often matter more than high-speed signal fidelity. The component should be selected only after checking the complete datasheet limits for supply voltage, input common-mode range, output current, and electrical characteristics.
This page combines the exact LM2901DR2G configuration with same-package alternatives, application-specific engineering guidance, a parameter comparison table, and practical layout considerations. These details help buyers distinguish the 14-SOIC part from other LM2901 order codes and assess whether it is appropriate for a new industrial, automotive, or consumer circuit without changing the PCB footprint.
直接替換替代品,適用於 LM2901DR2G — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2901DR2G (相同外形與佔位) — 差異在於 Comparator Type, Package, Input Bias Current, Output Type, Input Offset Voltage.
LM2901DR2
✅ 直接替換聯絡詢價
查看資料表 →LM2901DRG4
✅ 直接替換📋 參考替代品(不在目錄中)
LM2901DG4
✅ 直接替換聯絡詢價
查看資料表 →LM2901DR2
✅ 直接替換聯絡詢價
查看資料表 →LM2901QDRG4Q1
✅ 直接替換📋 參考替代品(不在目錄中)
LM2901DR2G 最大額定值與電氣特性
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| 工作溫度範圍 | -40°C to +105°C |
| 輸出類型 | Open collector |
| Logic Compatibility | CMOS and TTL |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
| Automotive-Grade Variant | NCV2901 family variant identified by onsemi |
LM2901DR2G 14-pin soic 腳位配置指南
LM2901DR2G(14-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2901DR2G.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2901DR2G 適用於 6 應用s: Automotive Battery Threshold Monitoring, Industrial Sensor Limit Detection, Power-Supply Fault Signaling, Consumer Level and Range Detection, Memory and Control Logic, Window Comparator and Signal Crossing Detection.
Automotive Battery Threshold Monitoring
The LM2901DR2G is well suited to automotive threshold-detection stages because four comparison channels operate from 3 V to 36 V within a -40°C to +105°C temperature range. Each channel can compare a divided battery signal with a reference and use its open-collector output to request an alert, inhibit a charger, or change an operating mode. Dividing the battery voltage protects the input range and allows multiple thresholds to be checked with only one IC. The open-collector output can also be pulled up to the vehicle logic supply, although the pull-up voltage must satisfy the device limits. For a production design, add transient protection at the battery input, verify the input common-mode range under cranking and load-dump conditions, and confirm automotive qualification against the selected order code.
推薦
Industrial Sensor Limit Detection
The LM2901DR2G can convert analog sensor conditions into logic events for industrial controllers. Its four independent channels reduce component count when monitoring temperature, pressure, level, or current thresholds, while the 3 V to 36 V supply range supports control systems operating above the lowest logic voltages. Each open-collector output can drive an isolated relay driver, PLC input, or fault line with a suitable pull-up resistor. The device's -40°C to +105°C range covers many industrial environments, but enclosure temperature and sensor accuracy still determine overall fault-detection performance. Engineers should add hysteresis to avoid chatter near a threshold, protect sensor inputs from transients, and verify input bias current, common-mode range, and output sink current before finalizing the interface network.
推薦
Power-Supply Fault Signaling
The LM2901DR2G is useful for monitoring multiple power rails or input thresholds in power-management equipment. Four comparators can evaluate divided feedback signals against stable references and produce open-collector fault outputs when a rail leaves its permitted range. The 3 V to 36 V operating capability suits systems with a wider input range than ordinary low-voltage logic ICs, while the four-channel package can consolidate overvoltage, undervoltage, sequencing, and enable checks. The design trade-off is that a linear regulator dissipates the difference between input and output voltage, so comparator current should remain modest where continuous monitoring is required. Pull-up resistors should be scaled to balance fault signaling speed with supply-current consumption, and every monitored input must remain inside the comparator's specified common-mode range.
推薦
Consumer Level and Range Detection
The LM2901DR2G supports compact consumer products that must identify when an analog signal enters or leaves a permitted range. Its four channels can monitor battery level, audio or sensor thresholds, charging conditions, or a divided system signal without requiring four separate packages. The open-collector outputs provide simple wired logic for a microcontroller or system controller, and their CMOS and TTL compatibility supports common digital input arrangements. In battery-powered equipment, however, continuous divider and pull-up currents can dominate standby consumption, so resistor values should be optimized without allowing excessive output rise time. Add positive feedback for hysteresis where the sensed signal has noise or slow transitions, and confirm that the chosen order code satisfies the product's environmental and component-qualification requirements.
推薦
Memory and Control Logic
The LM2901DR2G can implement simple memory-control and qualification functions where several analog or digital conditions must be resolved before a system changes state. Four open-collector channels may monitor voltage thresholds, acknowledge lines, or timing-derived control signals while operating from the same broad 3 V to 36 V supply range. Open-collector outputs are useful when a wired logic function is needed, but designers must account for the pull-up resistor's rise time and ensure that only one output actively sinks current when a wired-AND node is used. For reliable logic behavior, use clean pull-up connections, maintain adequate logic-level voltage margins, and verify propagation delay and input offset requirements against the timing budget. The onsemi datasheet should be used for the final pin assignments and electrical limits.
推薦
Window Comparator and Signal Crossing Detection
The LM2901DR2G can implement upper and lower window checks by pairing two comparison channels around a common reference. This arrangement is useful for battery, signal-strength, temperature, or supply-rail monitoring where the system must distinguish an in-range condition from both under-range and over-range faults. Its four channels allow two window functions in one package, reducing board area while maintaining open-collector fault outputs. The principal design challenge is reference accuracy: errors in the reference or resistor divider can shift the actual trip points. Use stable reference and feedback components, add hysteresis to prevent repeated output transitions, and keep the sensing node within the input common-mode limits across the full 3 V to 36 V operating range and -40°C to +105°C temperature span.
推薦
推薦產品摘要
工程參考資料,適用於 LM2901DR2G — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2901DR2 | LM2901DRG4 | LM2901DG4 | LM2901DR | LM2901QDRG4Q1 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Product Type | Quad differential comparator | Quad differential comparator | LM2901 family comparator | LM2901 family comparator | Quad differential comparator | LM2901 family comparator |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Primary Application | Level detection and low-level sensing | Level detection and low-level sensing | General-purpose comparison | General-purpose comparison | General-purpose comparison | Automotive comparison |
主要差異化特點
- Four independent threshold-detection channels in one package (對比LM2901DR)
- Wide single-supply operating range (對比LM2901DRG4)
- Open-collector outputs support flexible logic interfacing (對比LM2901QDRG4Q1)
- Wide environmental operating range (對比LM2901DG4)
設計說明
Place each open-collector pull-up resistor close to the associated LM2901DR2G output so that the physical loop between the device and receiver is minimized. This reduces susceptibility to capacitive coupling and keeps the logic transition path short. Route threshold-sensing traces away from inductors, switching nodes, and high-current return paths. When a fault output crosses a substantial distance, use a driver or differential interface rather than relying on a weak pull-up signal.
Do not treat an open-collector output as a push-pull logic output. A pull-up resistor is required to establish the high state, and its value determines both the logic rise time and the maximum sink current. Adding hysteresis with positive feedback is recommended when the compared signal contains noise or changes slowly near the threshold. The reference network and input divider should also avoid levels outside the device's specified common-mode range.
Estimated: a 10 kΩ pull-up connected to 5 V can source approximately 0.5 mA when the output is low, based on Ohm's law using 5 V and 10 kΩ inputs. This estimate illustrates the trade-off between low pull-up current and output rise time; the final value must also remain within the LM2901DR2G sink-current and receiver-input requirements. The manufacturer datasheet controls the allowable operating and electrical limits.
合規資訊
The onsemi family is described as available in an automotive-grade NCV2901 variant, but the compliance status of the exact LM2901DR2G order code requires confirmation from its current manufacturer product documentation.