Produk (46.000+)

MAX232BEAWE+ - 2/2 RS-232 Transceiver | Analog Devices
MAX232BEAWE+

MAX232BEAWE+ - 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices MAX232BEAWE+ is a 2/2 RS-232 transceiver integrated circuit packaged in a 16-pin SOIC. It combines two RS-232 drivers and two receivers in one device, providing a compact interface between logic-level UART equipment and a ±3 to ±15 V RS-232 communications link. The MAX232 family uses on-chip charge-pump circuitry to generate the bipolar voltage required by the RS-232 driver outputs, reducing the external component count compared with discrete level-shifting designs. An RS-232 transceiver is a signal-conversion device used to bridge the logic-voltage domain of a microcontroller, computer, or programmable controller and the voltage-domain requirements of an RS-232 port. Within the interface IC hierarchy, the MAX232BEAWE+ belongs to the RS-232 transceiver class of serial-interface ICs. Its two-driver, two-receiver arrangement suits point-to-point serial links that require bidirectional communication but do not need the larger channel count of a four-driver, four-receiver RS-232 implementation. The principal benefits are functional integration and compact PCB occupancy. Two transmit channels and two receive channels share one 16-pin SOIC package, while integrated level translation allows the same IC to support both RS-232 output and input signals. The package is suitable for conventional surface-mount PCB assembly, and the + suffix identifies the manufacturer's lead-free commercial ordering configuration. Because the MAX232 family is widely used in RS-232 equipment, designers can generally simplify firmware changes by treating the transceiver as a transparent UART-to-RS-232 interface. RS-232 transmitters require more voltage and current than ordinary CMOS or bipolar logic outputs. The MAX232BEAWE+ therefore functions as an interface boundary rather than as a general-purpose logic driver. Its internal charge-pump circuitry creates the bipolar voltage used by the drivers, while the receivers convert incoming RS-232 signals to a compatible logic level. This division of responsibilities allows the connected UART controller to operate with ordinary push-pull or open-drain interface circuitry while the cable side uses RS-232 levels. Typical uses include industrial serial-control equipment, test and measurement instruments, data-acquisition systems, configuration ports, and legacy service interfaces. A two-channel implementation can support one bidirectional communications path with an additional transmitter or receiver when directional requirements differ. It is also appropriate for embedded systems that retain an RS-232 port for compatibility with printers, scanners, controllers, or laboratory equipment even when the rest of the product uses modern digital interfaces. PCB implementation should follow the Analog Devices MAX232 datasheet for charge-pump capacitor placement, signal routing, and grounding. Keep the charge-pump capacitor connections short, provide the required ceramic capacitance close to the device, and route RS-232 driver outputs away from sensitive receiver inputs. Confirm the connector, cable, grounding, and logic levels before releasing the PCB because the IC solves voltage translation but does not define the complete RS-232 physical interface. This page combines the exact MAX232BEAWE+ package and interface configuration with same-family drop-in options, application guidance, comparison parameters, and practical RS-232 layout considerations. The alternatives are separated from cross-package designs so an engineer can focus on parts that preserve the 16-pin SOIC footprint.

Permintaan RFG Kontak
MAX232BEAWE+T - 2/2 RS-232 Transceiver | Maxim Integrated
MAX232BEAWE+T

MAX232BEAWE+T - 2/2 RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX232BEAWE+T is a 2/2 RS-232 transceiver, meaning it combines two line drivers and two line receivers in one device. The integrated circuit is supplied in a 16-pin SOIC package and is intended for bidirectional serial-interface designs requiring conversion between RS-232 signal levels and CMOS/TTL-compatible logic levels. Its two-driver, two-receiver arrangement allows two data channels to share one physical interface circuit. An RS-232 transceiver is an interface integrated circuit used to connect logic-level equipment to a serial port. The driver section converts low-voltage digital signals into RS-232-compatible levels, while the receiver section converts incoming RS-232 signals back into logic-compatible voltages. This transceiver belongs to the broader semiconductor hierarchy of interface ICs, line drivers and receivers, communication interfaces, and signal-conditioning semiconductors. The MAX232BEAWE+T provides a practical way to add two RS-232 channels without using separate driver and receiver packages. Its 16-SOIC format supports conventional surface-mount PCB assembly. The manufacturer documentation identifies the component as a 2/2 full RS-232 transceiver, allowing it to support both transmission and reception functions in systems such as industrial controllers, data-acquisition equipment, service interfaces, and embedded serial-port equipment. The MAX232 family is commonly used when legacy RS-232 equipment must communicate with a modern digital system. In a typical interface, the MAX232BEAWE+T sits between a host UART and an external RS-232 connector. Logic-level transmit signals enter the drivers, and the receivers return logic-level signals from the connector to the host. The IC therefore handles voltage translation at the physical interface while the UART handles character framing and serial protocol behavior. Typical uses include point-to-point control links, configuration interfaces, instrument-control ports, industrial equipment communication, and embedded service connections. Two integrated channels can reduce the component count compared with separate single-channel transceiver circuits. Board designers must still account for the external charge-pump capacitors, signal grounding, connector protection, cable routing, and the electrical limits that apply to the selected RS-232 standard and connected equipment. For layout, place the device close to the RS-232 connector or interface barrier, keep the driver and receiver routes short, and connect the charge-pump capacitor network exactly as shown in the manufacturer datasheet. The interface should also follow the recommended grounding and protection arrangement for the installed connector. Component values, electrical limits, timing characteristics, and environmental ratings should be confirmed against the datasheet for the exact MAX232BEAWE+T ordering code before release to production. This page combines the exact MAX232BEAWE+T device identification, package information, interface-application guidance, verified drop-in cross-reference options, and practical PCB considerations in a format intended to accelerate engineering selection and implementation.

Permintaan RFG Kontak
MAX232CASE+ - 5V Dual RS-232 Transceiver | Maxim Integrated
MAX232CASE+

MAX232CASE+ - 5V Dual RS-232 Transceiver | Maxim Integrated

Maxim Integrated MAX232CASE+ is a 5 V RS-232 transceiver with two drivers and two receivers, a maximum data rate of 120 kbps, and a 16-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and is specified for 0°C to 70°C commercial-temperature use. The MAX232CASE+ is an obsolete catalog designation, so procurement should focus on lifecycle confirmation and electrically qualified replacements rather than treating it as a new-design choice. An RS-232 transceiver is an interface IC that converts between logic-level signals used by digital systems and the voltage levels defined for RS-232 communications. The MAX232 belongs to the broader line-driver and line-receiver hierarchy: it combines a dual transmitter, a dual receiver, and an internal charge-pump supply that develops the bipolar voltages required for RS-232 transmission. This integration allows a modern controller or programmable logic device to connect to a legacy serial port using a single 5 V supply. The device provides two transmit channels and two receive channels in a full-duplex arrangement. Its maximum signaling rate is 120 kbps, while receiver hysteresis is 500 mV. The manufacturer describes the family as compliant with EIA/TIA-232E and V.28/V.24 interfaces, and the TI product page identifies ±9 V output levels and ±2 kV ESD protection for MAX232 devices. These characteristics make the interface suitable for control links, equipment communication, and legacy peripheral connections. Internally, the charge pump generates positive and negative voltage rails from the 5 V supply. The external charge-pump capacitors must use adequate voltage ratings and low effective series resistance because ripple on those rails can affect transmitter behavior. The receiver section provides noise tolerance through its 500 mV hysteresis, helping reject small voltage disturbances on a slow or noisy serial connection. Pin-compatible family members differ principally in temperature grade, shutdown capability, or power characteristics. Typical uses include industrial control panels, point-of-sale equipment, test systems, embedded instruments, and service ports that still use RS-232. For new designs, a currently supported family member should be preferred when its electrical ratings satisfy the application. For an existing MAX232CASE+ board, a replacement must match the 16-pin SOIC footprint, 5 V supply range, 2/2 channel configuration, capacitor connection pattern, and RS-232 signal levels. The principal design caution is that the obsolete ordering code should not be assumed to be an active production option. Confirm lifecycle status, temperature requirements, and the exact capacitor network before committing a replacement to a new PCB. Also preserve the required charge-pump capacitor values and place them close to their associated pins to minimize loop area and supply ripple. This page combines lifecycle information, interface specifications, drop-in family alternatives, application guidance, and PCB-focused engineering notes to support replacement planning. The comparison and design sections add practical selection context beyond the basic distributor listing, while the Request a Quote form supports current sourcing of the selected catalog number.

Permintaan RFG Kontak
MAX232CASE+T - 5V 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX232CASE+T

MAX232CASE+T - 5V 2Tx/2Rx RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CASE+T is a +5 V-powered, 2-transmitter and 2-receiver RS-232 transceiver packaged in a 16-pin SOIC. It converts between TTL/CMOS logic levels and EIA/TIA-232E serial-interface voltages, operating from -40 C to +125 C according to the MAX232 family documentation. The MAX232 family is designed for equipment where the external RS-232 port cannot directly connect to a microcontroller, FPGA, or other digital controller. An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between digital logic and serial communications. A transmitter converts TTL or CMOS data into bipolar RS-232 levels, while a receiver converts bipolar RS-232 signals back into logic-compatible levels. In the broader semiconductor hierarchy, the MAX232 belongs to interface ICs, then transceiver ICs, then RS-232 line drivers and receivers. Key characteristics include two RS-232 transmitters, two RS-232 receivers, operation from a single +5 V supply, and a 16-SOIC footprint. The MAX232 family is intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where positive and negative RS-232 voltage rails are not otherwise available. This makes it suitable for legacy serial ports, service interfaces, industrial controllers, and embedded debug links. The device uses charge-pump circuitry to generate the negative RS-232 voltage required by the transmitters. Charge pumps, external capacitors, receiver inputs, and transmit outputs therefore form one signal-path subsystem; component placement and trace routing determine whether the interface meets the timing and noise expectations of the connected equipment. The receiver section converts bipolar input signals into a single-ended logic output for the host controller. Typical uses include point-to-point RS-232 links between a microcontroller and a peripheral, service-console connections in industrial equipment, legacy printer or instrument interfaces, and isolated debugging ports. The two-transmitter, two-receiver arrangement supports one hardware flow-control pair alongside the primary data pair when the connected equipment uses RTS and CTS signaling. For a new layout, follow the manufacturer datasheet for capacitor selection, charge-pump placement, and driver-output routing. Place the required charge-pump capacitors close to their associated pins, keep RS-232 driver traces away from sensitive logic and clock nets, and confirm that the equipment-side ground and shield strategy matches the target system. This page adds practical replacement guidance, package-level comparison, application-specific design guidance, and engineering-focused FAQ answers that complement the manufacturer datasheet. It also identifies where a pin-compatible substitution must be checked for temperature grade, supply requirements, and channel-level functional differences before an existing layout is reused.

Permintaan RFG Kontak
MAX232CEASE+ - 5V 2/2 RS-232 Transceiver | Analog Devices
MAX232CEASE+

MAX232CEASE+ - 5V 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CEASE+ is a +5 V-powered RS-232 transceiver containing two drivers and two receivers in a 16-pin SOIC package. It converts logic-level UART signals to and from RS-232 line levels, allowing equipment with a serial controller to communicate through a conventional RS-232 port. The device operates from a single 5 V supply while producing the bipolar voltage levels required by RS-232 interfaces. An RS-232 transceiver is an interface IC positioned between digital logic and a serial communications connector. Within the product hierarchy, it belongs to the RS-232 interface transceiver family and the broader category of interface ICs. Its two-driver, two-receiver arrangement supports one bidirectional RS-232 channel or two unidirectional channels, depending on how the pins are connected. Unlike a UART, which generates and interprets serial data but does not provide RS-232 voltage levels, the MAX232CEASE+ performs the physical-layer conversion between CMOS/TTL logic and RS-232. The principal features are a +5 V supply, two transmit drivers, two receive receivers, full RS-232 operation, and a 16-pin SOIC footprint. The integrated charge-pump circuitry supports the positive and negative signal swings required at the driver outputs while the receiver inputs handle the bipolar RS-232 signal range. This makes the device useful where a modern microcontroller or application-specific controller has a UART but lacks a physical RS-232 level-shifting interface. The MAX232 family is specified for EIA/TIA-232E and V.28/V.24 communications interfaces, including designs where ±12 V is unavailable. The single-supply architecture simplifies implementation compared with a discrete bipolar level-shifter circuit. Its 2/2 channel organization also provides flexibility for two independent transmit-only or receive-only links when all four interface pins are not needed in a single bidirectional port. Typical applications include industrial serial adapters, test and measurement equipment, computer peripherals, security systems, and embedded-control subsystems. In each case, the transceiver provides the electrical interface between a low-voltage UART and an RS-232 port while keeping the host-side logic supply at +5 V. PCB implementation should prioritize short driver traces, controlled return paths, and proper connection of the charge-pump capacitors specified by the manufacturer. External protection may be required when the RS-232 cable is exposed to electrostatic discharge or when the connected equipment uses longer cables. This page combines the manufacturer interface description, package information, verified replacement candidates, comparison guidance, and practical PCB design notes. These engineering details help evaluators determine pin compatibility, electrical suitability, and implementation trade-offs before committing the MAX232CEASE+ to an RS-232 design.

Permintaan RFG Kontak
MAX232CEASE+T - 5V 2/2 RS-232 Transceiver | Analog Devices
MAX232CEASE+T

MAX232CEASE+T - 5V 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CEASE+T is a 5 V-powered RS-232 interface transceiver with two transmitters and two receivers, packaged in a 16-pin SOIC. It supports the full RS-232 signal amplitude required for reliable point-to-point serial communication and is specified across the -40°C to +125°C industrial temperature range. The device consolidates both directions of an RS-232 port into one compact interface package. An RS-232 transceiver is a semiconductor interface device that converts between complementary TTL/CMOS logic levels and bipolar RS-232 signals. Its transmitter section translates low-voltage digital logic into RS-232-level outputs, while its receiver section converts RS-232 inputs back into digital logic. This bridge function belongs to the interface IC hierarchy, where it supports the larger category of wired data-communication and industrial-control systems. The MAX232CEASE+T provides two transmit channels and two receive channels, allowing two unidirectional serial links to share one package. Its single 5 V supply simplifies system power design, while the integrated level-shifting circuitry removes the need for discrete RS-232 driver and receiver stages. These features make the device suitable for industrial controllers, test equipment, instrumentation, and embedded systems that exchange RS-232 commands or data with peripheral equipment. The MAX232 family is commonly used where legacy RS-232 connectivity must coexist with modern digital logic. A system microcontroller or programmable logic controller can connect its logic-level pins directly to the transceiver, while the board-level RS-232 connector handles the external cable interface. The two receivers and two transmitters provide flexible channel allocation when one direction carries data and another carries control, status, or handshake signaling. Designers should account for RS-232 voltage levels, connector pin assignments, and grounding when laying out a board. The IC should be placed near the protection and connector circuitry, with short traces on logic signals and controlled return paths for cable-generated noise. Decoupling capacitance should follow the manufacturer’s recommended application circuit, and unused interface pins should be handled according to the pin-description and unused-pin guidance in the datasheet. This page combines the device’s principal interface specifications with engineering-oriented selection guidance, application context, package information, and verified drop-in candidates. It is intended to help engineers identify the correct temperature grade, verify board compatibility, and implement a dependable RS-232 interface without confusing package similarity with full electrical equivalence.

Permintaan RFG Kontak
MAX232CEAWE+ - +5V RS-232 Transceiver | Analog Devices
MAX232CEAWE+

MAX232CEAWE+ - +5V RS-232 Transceiver | Analog Devices

Analog Devices MAX232CEAWE+ is a +5V-powered, 2/2 RS-232 transceiver designed for EIA/TIA-232E, V.28, and V.24 communications interfaces. The device combines two line drivers and two line receivers in a 16-SOIC package, allowing one component to implement a complete dual-channel RS-232 interface. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and RS-232 line drivers and receivers. The MAX232 family belongs to the interface IC hierarchy, where transceiver ICs bridge digital logic systems with the voltage levels, slew rates, and noise-immunity requirements of balanced or unbalanced serial communications. It is particularly useful where the equipment does not provide the traditional positive and negative RS-232 supply rails. The MAX232CEAWE+ uses a single +5V supply, combining two transmit channels and two receive channels in one package. This integration reduces the number of components required for a bidirectional RS-232 port. Its stated interface compatibility includes EIA/TIA-232E, V.28, and V.24 systems, while its 16-SOIC format supports conventional surface-mount PCB assembly. The E designation identifies an industrial-temperature device within the MAX232 family. Operationally, the transmitter portion converts TTL or CMOS logic levels into RS-232-compatible signal levels, while the receiver portion converts incoming RS-232 signals into logic-compatible outputs. The MAX232 family is intended specifically for communications interfaces where positive and negative supply voltages are unavailable. Its internal charge-pump approach allows +5V-powered equipment to implement RS-232 links without external negative-rail generation circuitry. Typical applications include industrial serial adapters, data-acquisition equipment, instrumentation, embedded controller interfaces, point-of-sale systems, and legacy peripheral connections. A two-driver, two-receiver arrangement is useful for consoles, debug ports, programmable instruments, and control systems that exchange data in both directions over separate RS-232 channels. PCB design should prioritize short return paths and controlled return current around the interface. Place the device close to the connector and keep unprotected RS-232 traces away from sensitive analog or high-speed digital nets. The manufacturer's pin-description table should be used when assigning connector-side and logic-side signals, and external protection should be selected for the cable length and installation environment. This product page combines the manufacturer interface description with package, application, and drop-in selection guidance. It also highlights where temperature-grade, ESD-protection, and footprint differences matter when comparing MAX232-family devices for an existing 16-SOIC PCB design.

Permintaan RFG Kontak
MAX232CEAWE+T - 2/2 RS-232 Transceiver | Analog Devices
MAX232CEAWE+T

MAX232CEAWE+T - 2/2 RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CEAWE+T is a 2/2 full RS-232 transceiver with one driver and one receiver implemented in each direction, a 16-SOIC package, and an operating temperature range of -40°C to +125°C. The device is powered from +5 V and is intended for translating logic-level digital signals to and from RS-232 voltage levels. An RS-232 transceiver is an interface IC that combines drivers and receivers for serial data communication. The driver converts a logic-level input into the bipolar voltage signaling used by RS-232, while the receiver converts a bipolar RS-232 input into a logic-level output. As a full-duplex 2/2 device, the MAX232CEAWE+T supports two transmit channels and two receive channels in one package. Its principal features include two RS-232 drivers, two RS-232 receivers, operation from a +5 V supply, and operation from -40°C to +125°C. The extended temperature range makes the device suitable for industrial equipment, control systems, instrumentation, and communications equipment that must operate across a broad environmental range. The 16-SOIC package supports conventional surface-mount PCB assembly. The MAX232 family combines a dual RS-232 driver and dual receiver with charge-pump voltage generation, allowing the interface to produce RS-232 levels from a single positive supply. Because this is an integrated transceiver, a system can use fewer discrete interface components than a design composed of separate drivers, receivers, and level-shifting circuits. Charge-pump capacitors and supply-decoupling components remain external to the IC. Typical uses include serial service ports, industrial controllers, data-acquisition equipment, test and measurement instruments, and embedded systems that communicate with RS-232 equipment. The two-driver and two-receiver arrangement is useful for point-to-point links where both ends can transmit and receive. A transceiver does not define the serial baud rate or protocol framing; those functions are handled by the host UART and application firmware. For PCB implementation, place the required charge-pump and bypass capacitors close to their associated pins, route the RS-232 driver outputs as impedance-controlled interfaces, and keep switching or high-current paths away from receiver inputs. Confirm the logic levels of the attached UART before connecting the transceiver because RS-232 voltage levels are not directly compatible with TTL or CMOS logic. This product guide combines the exact MAX232CEAWE+T device information with application guidance, engineering considerations, and clearly qualified drop-in comparison options. It also organizes sourcing, datasheet, replacement, and pinout questions so engineers can evaluate the interface quickly without overlooking temperature-range, package, or supply requirements.

Permintaan RFG Kontak
MAX232CPE - 5V RS-232 Transceiver, 2 Driver/2 Receiver, 16-PDIP
MAX232CPE

MAX232CPE - 5V RS-232 Transceiver, 2 Driver/2 Receiver, 16-PDIP

The Maxim Integrated (Analog Devices) MAX232CPE is a +5V-powered, dual-driver/dual-receiver RS-232 transceiver housed in a 16-pin PDIP (PE) through-hole package. It operates from a single 5V supply using on-board charge-pump capacitors to generate the ±10V RS-232 signal levels, eliminating the need for a ±12V power source. The device conforms to the EIA/TIA-232E and V.28/V.24 communication interface standards and supports data rates up to 120 kbps, satisfying asynchronous serial-port requirements for PCs, embedded controllers, and point-of-sale terminals. An RS-232 transceiver is a line driver/receiver IC that converts between transistor-transistor logic (TTL/CMOS) voltage levels used by microcontrollers and the higher-voltage bipolar signaling levels defined by the EIA/TIA-232 standard. As a member of the line-driver/receiver IC class within Interface ICs, the MAX232 family uses external charge-pump capacitors (typically 1 µF to 10 µF) to double and invert the 5V supply, producing the ±10V swing required by RS-232. This topology removes the legacy dependence on ±12V rails that earlier RS-232 implementations required. Key features include two RS-232 drivers with ±9V output swing (typical), two RS-232 receivers with TTL/CMOS compatible outputs, an integrated dual charge pump requiring only four external 1 µF capacitors, low supply current of 8 mA typical, and an operating temperature range of 0°C to +70°C (commercial grade). The MAX232CPE differs from the higher-speed MAX232EPE (which extends to 250 kbps) and the wide-temperature MAX232AEPE (which extends to -40°C and adds 15 kV ESD protection on the driver outputs). The MAX232 family uses a proprietary dual charge-pump architecture that converts +5V into +10V and -10V using only four external capacitors. The drivers meet the EIA/TIA-232E and V.28 specifications with minimum ±5V output swing into 3 kΩ loads, while the receivers accept ±25V inputs and present 5 kΩ input resistance to the line. The MAX232CPE ships in the 16-pin PDIP (PE) through-hole package with pinout identical to the MAX232EPE, MAX232AEPE, SP232ACP-L, and other industry-standard drop-in equivalents. Typical applications include microcontroller UART-to-RS-232 level translation, industrial point-of-sale (POS) terminals, networking equipment console ports, embedded debug and programming interfaces, and legacy serial peripheral interconnects (modems, instrumentation, barcode scanners). The wide input tolerance of the receivers (±25V) tolerates mis-wiring and noisy RS-232 environments. When designing with this device, place the four charge-pump capacitors as close as possible to the IC pins and use 1 µF (or larger) ceramic or tantalum types to maintain ±10V output levels. Verify that the data rate does not exceed 120 kbps, as the MAX232CPE is not designed for higher-speed operation; for that, select the MAX232EPE (250 kbps) or MAX232AEPE (200 kbps) variants. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical PCB layout guidance not collated in the original manufacturer datasheet.

Permintaan RFG Kontak
MAX232CPE-C70055 - RS-232 Transceiver | Analog Devices
MAX232CPE-C70055

MAX232CPE-C70055 - RS-232 Transceiver | Analog Devices

Analog Devices MAX232CPE-C70055 is a dual RS-232 line-driver and receiver transceiver integrated circuit in a 16-pin PDIP package. The device provides two transmit channels and two receive channels for converting TTL/CMOS logic levels to and from EIA/TIA-232E-compatible signal levels. Its primary role is to bridge a digital controller, computer, or microcontroller UART with a physical RS-232 port, allowing equipment to communicate over a wired serial interface without a separate level-conversion circuit. The MAX232 family belongs to the interface-IC hierarchy: RS-232 transceiver -> line driver and receiver -> logic interface IC -> semiconductor. A MAX232-type device uses an on-chip charge-pump voltage converter to generate the positive and negative voltages required by RS-232 drivers. This allows a circuit powered from a single positive supply to communicate with equipment using RS-232 signal levels. The device is intended for applications where traditional RS-232 communication is required but higher-speed differential or differential alternatives are not appropriate. The C70055 ordering suffix identifies a specific manufacturer-specified configuration associated with the MAX232CPE family. The verified product information identifies the device as a dual-driver, dual-receiver RS-232 interface IC in a 16-pin PDIP package. The standard MAX232CPE family is described as an EIA/TIA-232E and V.28/V.24-compatible interface for systems where positive and negative supply rails are unavailable. Key engineering considerations include the external charge-pump capacitor values, supply bypass, unused-line handling, and the difference between logic-level and RS-232-level signals. Typical uses include industrial control equipment, data acquisition systems, service interfaces, test fixtures, serial adapters, and embedded equipment that needs a conventional RS-232 port. The MAX232 is most appropriate when the system uses a UART with TTL logic and requires a legacy RS-232 connector. It is not the right choice when the design needs galvanic isolation, very high data rates, long unrepeated cable distances, or modern USB-to-serial conversion. A practical design should follow the manufacturer's application circuit, including the specified charge-pump capacitors, local supply decoupling, and controlled handling of unused receiver and driver outputs. PCB placement should keep the charge-pump loop compact and connect the connector-side return path carefully to reduce noise pickup. For a new design, verify the exact C70055 ordering code, electrical limits, and package drawings against the current Analog Devices or Maxim Integrated documentation before releasing the PCB.

Permintaan RFG Kontak
MAX232CPE.C70062 5V RS-232 Transceiver | Analog Devices
MAX232CPE.C70062

MAX232CPE.C70062 5V RS-232 Transceiver | Analog Devices

Analog Devices MAX232CPE.C70062 is a 5 V RS-232 line-driver and receiver transceiver with two driver and two receiver channels, packaged in a 16-pin PDIP. It is designed for EIA/TIA-232E and V.28/V.24 communications interfaces where positive and negative supply voltages around ±12 V are not available. The MAX232 family uses onboard charge-pump circuitry to generate the negative voltage required by the RS-232 receiver threshold. An RS-232 transceiver is an interface IC that translates logic-level signals between a computer or controller and a cable-based serial link. The MAX220–MAX249 family belongs to the RS-232 interface hierarchy, which includes line drivers, line receivers, transceivers, and interface controller devices. This distinction matters because an RS-232 transmitter converts single-ended digital logic into a bipolar differential signal, while its receiver restores the logic-level signal received from the cable. The MAX232CPE.C70062 provides a 16-pin PDIP package, a nominal 5 V supply, and two transmit plus two receive channels. Its principal system benefit is the elimination of separate negative power rails at the transceiver. The integrated charge-pump circuit generates the negative bias needed to interpret RS-232 receive levels, allowing the device to operate from a single positive supply while maintaining compatibility with standard RS-232 equipment. Typical uses include industrial control interfaces, serial service ports, instrumentation, embedded equipment, and legacy peripheral connections. Designers should use the manufacturer pin-description table when assigning connector signals and should account for the non-logic RS-232 voltage levels at the line pins. The communications path also requires suitable board layout, cable selection, grounding, and protection practices to achieve reliable operation in industrial environments. The MAX232CPE.C70062 is the MAX232CPE part number with the C70062 customer ordering suffix. Verify the suffix, package marking, shipping configuration, and documentation revision before releasing a production order. Because this suffix identifies a specific ordering configuration, engineers should treat it as a distinct line item rather than silently substituting the base MAX232CPE designation. This page consolidates interface details, package information, application guidance, and verified drop-in alternatives for MAX232CPE.C70062. It also provides selection criteria for comparing same-footprint transceivers without confusing a functional alternative with a true pin-to-pin replacement. Review the electrical limits and pin descriptions in the manufacturer datasheet before finalizing a circuit. For a new design, confirm availability, lifecycle expectations, and the exact ordering code through the Request a Quote form on this page. For an existing PCB, validate the pinout, supply voltage, channel count, and RS-232 electrical requirements before approving any alternative.

Permintaan RFG Kontak
MAX232CSE+ - Dual RS-232 Transceiver, 16-SOIC | Analog Devices
MAX232CSE+

MAX232CSE+ - Dual RS-232 Transceiver, 16-SOIC | Analog Devices

Analog Devices MAX232CSE+ is a dual RS-232 line-driver and receiver IC with one transmitter and one receiver per channel, a 4.5 V to 5.5 V supply range, and a 16-pin SOIC package. It is designed to add bipolar RS-232 signal conditioning to systems whose logic-side supply is 5 V and whose external interface does not provide the positive and negative voltages required by the EIA/TIA-232E standard. An RS-232 transceiver is an interface IC that converts low-voltage logic-level signals into differential, bipolar line signals and converts received line signals back into logic-compatible levels. The MAX232 belongs to the RS-232 interface transceiver category, combining line drivers, line receivers, and an on-chip charge-pump voltage converter in one package. This integration allows a 5 V circuit to communicate with legacy serial equipment without a separate negative-power supply. The device provides two driver channels and two receiver channels, supporting full-duplex serial communication when both directions are used. Its 4.5 V to 5.5 V operating supply supports conventional 5 V digital systems, while the internal charge pump generates the positive and negative voltages required to drive RS-232 loads. The wide-logic compatibility and integrated level translation make the MAX232 suitable for UART-based links, control equipment, and legacy peripheral connections. The MAX220 through MAX249 family is specified for EIA/TIA-232E and V.28/V.24 communications interfaces. This is particularly important where the equipment must interoperate with older RS-232 ports rather than only with modern low-voltage serial standards. The C suffix identifies the capacitor and operating-temperature configuration, while the E suffix denotes the narrow SOIC package and the trailing plus identifies the lead-free ordering code. Typical uses include industrial controller-to-console links, configuration ports on test equipment, service interfaces for printers and scanners, and communication links between 5 V microcontrollers and RS-232 equipment. The two receiver channels can also monitor two incoming lines when only one transmit channel is needed. System designers should account for the charge-pump capacitors, grounding, logic levels, and the slower edge rates associated with the selected RS-232 implementation. Place the charge-pump capacitors and interface-decoupling capacitor close to their associated pins and route driver outputs and receiver inputs away from sensitive clock, reset, and analog signals. Keep the ground and supply return paths short because the receiver must distinguish small logic-side transitions from bipolar RS-232 levels. Confirm signal polarity, baud rate, and flow-control requirements at the software interface before replacing an existing MAX232 implementation. This product page combines the confirmed electrical identity, package information, interface standards, and drop-in alternatives with application-oriented design guidance. It helps engineers identify the correct RS-232 transceiver, verify footprint compatibility, and plan charge-pump capacitance and PCB layout before committing a MAX232CSE+ to a new PCB.

Permintaan RFG Kontak
MAX232CSE+T - +5V RS-232 Transceiver, 16-SOIC | Analog Devices
MAX232CSE+T

MAX232CSE+T - +5V RS-232 Transceiver, 16-SOIC | Analog Devices

The Analog Devices (formerly Maxim Integrated) MAX232CSE+T is a +5V-powered, multichannel RS-232 driver/receiver IC in a 16-pin narrow-body SOIC (SOIC-N-16) package. It integrates two RS-232 line drivers and two RS-232 line receivers and generates the required ±7.5V to ±12V RS-232 output levels from a single +5V supply via on-board charge-pump capacitors. The part is supplied in tape-and-reel (T+R) packaging and supports data rates up to 120 kb/s per the MAX232C variant specifications. A RS-232 transceiver (line driver/receiver) is an interface IC that translates logic-level signals (typically 0/5V or 0/3.3V CMOS/TTL) to the higher-voltage bipolar signaling levels defined by the EIA/TIA-232E and V.28/V.24 standards. These standards require driver outputs above ±5V into 3 kΩ loads and receivers that translate bipolar inputs to standard logic levels. The MAX232 sits in the interface IC family within the broader integrated circuits hierarchy: interface IC > transceiver > line driver/receiver > signal conditioning IC > semiconductor. Key features include single +5V operation eliminating the need for ±12V rails, integrated charge-pump voltage doubler/inverter requiring only four external 1 µF capacitors, true RS-232 compliant outputs (typically ±7.5V minimum), and on-board TTL/CMOS-compatible receiver inputs with 5 kΩ resistive pull-down to ground. The wide commercial operating temperature range (0 °C to +70 °C for the C-grade) suits point-of-sale terminals, industrial control consoles, and embedded serial ports. Architecturally, the MAX232 uses a switched-capacitor charge pump (typically a dual-pump Dickson topology) with internal MOSFET switches clocked above the audio band. This generates the negative rail from the +5V supply without inductors, keeping the solution purely capacitive. Receivers employ hysteresis on their inputs to reject noise on long cables. Typical applications include RS-232 serial ports on microcontrollers (Arduino, PIC, STM32), point-of-sale (POS) terminals, industrial control equipment, networking routers and switches with console ports, and legacy PC peripherals. The 16-SOIC narrow-body package and tape-and-reel shipping suit high-volume automated assembly. When designing, place the four charge-pump capacitors as close to the C1+, C1-, C2+, C2- pins as possible using short traces, and use the V+ and V- pins as additional bypass. For higher data rates above 120 kb/s or extended temperature ranges, consider the MAX232E (200 kb/s, -40 °C to +85 °C) or MAX3232 (3V to 5.5V operation) families. This page synthesizes distributor pricing, drop-in cross-brand alternatives such as the Sipex/MaxLinear SP232ACN-L/TR, and practical charge-pump layout guidance not typically consolidated in the manufacturer datasheet.

Permintaan RFG Kontak
MAX232CWE+ - 5V Dual RS-232 Transceiver | Analog Devices
MAX232CWE+

MAX232CWE+ - 5V Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE+ is a +5 V-powered, dual RS-232 driver and receiver interface IC with two transmit channels and two receive channels, supplied in a 16-pin wide SOIC package. The verified distributor listing identifies it as a 2/2 full RS-232 transceiver, while the datasheet describes the MAX220-MAX249 family as line-driver and receiver devices intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12 V is unavailable. Its single-supply operation is valuable in battery-powered and modern digital systems that cannot provide conventional bipolar RS-232 rails. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the differential, bipolar signaling used by RS-232 links. The transmitter portion accepts TTL/CMOS-compatible inputs and produces RS-232 output levels, while the receiver portion accepts RS-232 inputs and returns logic-level signals to a host, controller, or peripheral. In the system hierarchy, the MAX232 belongs to interface ICs, serial-interface transceivers, and communication adapters rather than to the power-conversion or digital-processing categories. Key verified features include operation from a 4.5 V to 5.5 V supply, two drivers, two receivers, RS-232 interface compatibility, and a 16-pin wide SOIC package. The MAX232 family is specifically suited to EIA/TIA-232E and V.28/V.24 links and includes on-chip charge-pump support for generating the required RS-232 voltage levels from a single supply. Exact driver slew rate, receiver propagation delay, input and output capacitance, and shutdown-current details were not supplied in the retrieved data and should be confirmed from the manufacturer datasheet before precision timing or signal-integrity design. Typical applications include serial debug consoles, industrial-control equipment, instrumentation, point-of-sale systems, and legacy peripheral interfaces. The device is appropriate where a controller UART needs a compliant RS-232 electrical interface but the board cannot provide ±12 V. Designers should still verify cable length, data rate, grounding, protection requirements, and the logic levels of the connected host. This page combines the verified product identity, package information, interface purpose, distributor records, and cross-reference findings into an engineering-oriented selection summary. A key design consideration is to place the MAX232 close to the board connector and provide the required charge-pump capacitors exactly as specified by the manufacturer datasheet. Keep the RS-232 traces away from sensitive analog and high-speed digital paths, and provide suitable transient protection for exposed external connectors. The verified excerpts do not provide operating temperature, RoHS, REACH, lifecycle, or exact absolute-maximum ratings, so those values remain unconfirmed. This page consolidates verified distributor and cross-reference information, same-package RS-232 design guidance, and explicit engineering trade-offs that are not visible in a basic catalog listing. It is intended to support initial component selection while directing engineers to the official MAX232 datasheet and distributor records for final qualification.

Permintaan RFG Kontak
MAX232CWE+T - Dual RS-232 Transceiver | Analog Devices
MAX232CWE+T

MAX232CWE+T - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE+T is a +5 V-powered, dual RS-232 line-driver and receiver IC providing one full-duplex RS-232 port in a 16-pin wide SOIC package. It supports data rates up to 120 kbps and targets EIA/TIA-232E, V.28, and V.24 communications interfaces. Its integrated charge-pump circuitry generates the positive and negative voltages required by RS-232 without a separate external power supply. An RS-232 transceiver is an interface IC that converts logic-level signals into differential bipolar RS-232 levels and converts received bipolar signals back into CMOS-compatible logic. The MAX232CWE+T belongs to the line-driver and receiver hierarchy, providing the physical-layer functions required to connect a UART, microcontroller, or embedded controller to a serial port. It is particularly useful where the system cannot provide the positive and negative rails normally associated with RS-232 equipment. Key features include two driver channels, two receiver channels, a single +5 V supply, and operation at 120 kbps. The charge-pump design permits RS-232 communication with only +5 V power, eliminating a dual-supply requirement and reducing board-level complexity. The wide SOIC package is a standard surface-mount option with adequate lead pitch for automated assembly and hand-soldering. The device uses five external charge-pump capacitors to develop the bipolar voltage levels required for reliable transmission. Designers should place these capacitors close to the associated device pins and follow the connection arrangement in the manufacturer datasheet. Short, direct signal paths on the printed circuit board help limit ringing, reduce radiated emissions, and preserve the receiver's input threshold margin. Typical uses include industrial serial consoles, instrumentation links, service equipment, barcode readers, point-of-sale terminals, and legacy peripheral connections. The MAX232CWE+T is appropriate where a +5 V system must communicate over an RS-232 cable with a host computer or controller while avoiding the older +12 V and -12 V supply architecture. Choose this part when the required data rate is 120 kbps or lower and a 16-pin wide SOIC footprint is already on the PCB. Verify signal levels, cable length, grounding, and receiver thresholds at the system level, because RS-232 is a single-ended interface that depends on a common reference between connected equipment. This page combines the manufacturer interface description with practical component comparison, pin-level implementation guidance, and design notes covering charge-pump capacitors, grounding, transmission limits, and second-source evaluation.

Permintaan RFG Kontak
MAX232CWE-TG074 - 120kbps RS-232 Transceiver | Analog Devices
MAX232CWE-TG074

MAX232CWE-TG074 - 120kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX232CWE-TG074 is a dual-driver, dual-receiver RS-232 line transceiver rated for data rates up to 120kbps and housed in a 16-pin SOIC package. It provides the electrical conversion between RS-232 logic-level signals and bipolar serial data, including the voltage translation required on both driver and receiver sides. The device is intended for EIA/TIA-232E and V.28/V.24 communications interfaces where ±12V supplies are unavailable. A MAX232 is a bipolar RS-232 interface IC that converts TTL/CMOS-compatible logic signals into RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, it belongs to the line-driver and receiver category, interface IC family, and broader semiconductor product group. Two driver channels and two receiver channels allow one device to support a full-duplex serial link. The MAX232CWE-TG074 supports operation at up to 120kbps, making it suitable for common serial-console, industrial-control, point-of-sale, and embedded equipment links. Its integrated level translation reduces the need for external RS-232 driver and receiver components. The 16-SOIC package supports conventional surface-mount assembly and is suitable for compact industrial and commercial equipment designs. The MAX220 through MAX249 family is designed around EIA/TIA-232E and V.28/V.24 interface requirements, particularly where positive and negative supply voltages of approximately ±12V are not available. The CWE-TG074 ordering form identifies this part as a 16-SOIC RS-232 driver/receiver interface with two drivers and two receivers. Its interface architecture supports simultaneous transmit and receive paths when the host and peripheral provide complementary data and control signals. Typical applications include configuration-port and console interfaces in embedded systems, communication links between microcontrollers and industrial peripherals, RS-232 test equipment, and legacy peripheral connections requiring bidirectional data transfer. Designers should pay particular attention to cable length, signal integrity, grounding, and the distinction between logic-level and RS-232 voltage domains. For a new layout, place the MAX232CWE-TG074 close to the connector and preserve short, direct routes for the driver outputs and receiver inputs. Check the device's receive thresholds and the logic-level supply requirements of the connected controller. Add the charge-pump capacitors recommended by the manufacturer at the designated pins and avoid long stubs that could increase ringing or susceptibility to ESD events. This product page combines the available manufacturer-family information, package identification, interface characteristics, application guidance, and drop-in replacement options in a format designed for engineering selection. For complete channel assignments, absolute maximum ratings, electrical characteristics, and layout guidance, use the official MAX232CWE datasheet and the exact pin-description table before releasing a PCB or production design.

Permintaan RFG Kontak
MAX232D - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI
MAX232D

MAX232D - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI

The Texas Instruments MAX232D is a 5V-powered, dual-driver / dual-receiver RS-232 transceiver that integrates an on-board capacitive charge-pump to generate the +/-9V TIA/EIA-232-F signaling voltages from a single 5V supply, delivered in a 16-pin SOIC (D) package. It supports data rates up to 120 kbps, accepts +/-30V input levels on the receiver inputs, and supplies 8 mA typical quiescent current from a 4.5V to 5.5V supply rail. The device is functionally designed to be interchangeable with the industry-standard Maxim MAX232 die. A dual EIA-232 (RS-232) line driver/receiver is an interface IC that bridges TTL/CMOS logic levels (0-5V) and the much higher bipolar voltage swings (+/-5V to +/-15V) required by legacy serial-port standards. By generating these higher rails internally from a single low-voltage supply, dual RS-232 transceivers eliminate the need for a separate negative or high-voltage power rail, simplifying board design and reducing BOM cost. In the broader product hierarchy, the MAX232D belongs to the EIA-232 transceiver family (RS-232 transceiver), then to the Interface ICs category, then to Integrated Circuits, ultimately serving as an enabler of UART-to-DB9 connectivity in microcontroller- and FPGA-based systems. Key features of the MAX232D include TIA/EIA-232-F and ITU V.28 compliance, +/-30V receiver input tolerance that survives mis-wired cables and transients, an integrated 5V-to-+/-10V charge pump with four external 1 uF capacitors (charge-pump flying capacitors), two drivers and two receivers in a single 16-pin SOIC package, and ESD protection on the RS-232 bus pins (per the family spec). The 120 kbps data rate is more than adequate for serial console, modem, and industrial telemetry traffic, while the wide 4.5V to 5.5V supply range accommodates standard 5V regulated rails and battery-powered designs with headroom. Architecturally, the charge pump uses a voltage-doubler plus an inverting charge pump clocked from an internal oscillator (typically 125 kHz to 250 kHz range), which provides the +10V and -10V rails that drive the RS-232 output stages. The receivers use Schmitt-trigger inputs with hysteresis for noise immunity on long cables. Compared to using a discrete transistor-based level shifter or a +-12V linear supply, the MAX232D solution occupies roughly 30 mm x 6 mm of board area and removes one power supply from the design. Typical applications include microcontroller UART-to-RS-232 conversion on serial ports of industrial PLCs, point-of-sale (POS) terminals, embedded debug consoles for firmware development, and legacy PC RS-232 COM ports. The MAX232D is also commonly deployed in factory automation where 5V microcontrollers need to drive RS-232-controlled motor drives or sensors. Other uses include test and measurement equipment (scopes and analyzers with serial ports), legacy networking gear with DB-9 management ports, and education/development boards (Arduino shield, FPGA dev kit UART bridges). When designing with the MAX232D, observe charge-pump capacitor polarity: TI recommends 1 uF (or larger) low-ESR ceramic capacitors on each of the four charge-pump pins (C1+, C1-, C2+, C2-, V+, V-). Place the capacitors as close to the IC as possible to minimize parasitic resistance and ringing. Avoid long cable stubs on T1OUT/T2OUT pins, and add TVS diodes for additional ESD protection if the application involves frequent cable mating/unmating. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX232DE4 - Dual RS-232 Transceiver, 5V, 16-SOIC | Texas Instruments
MAX232DE4

MAX232DE4 - Dual RS-232 Transceiver, 5V, 16-SOIC | Texas Instruments

The Texas Instruments MAX232DE4 is a dual RS-232 driver and receiver transceiver with two drivers, two receivers, a single 4.5 V to 5.5 V supply, and a 16-pin SOIC package. It supports data rates up to 120 kbit/s and includes on-chip charge-pump capacitors for generating the bipolar RS-232 voltage levels. The device is designed for bidirectional serial data links between TTL/CMOS logic and EIA/TIA-232 equipment. An RS-232 transceiver is an interface IC that translates low-voltage digital logic levels into RS-232 levels and converts incoming RS-232 signals back into TTL/CMOS levels. The MAX232 belongs to the interface IC hierarchy, where a transceiver integrates driver, receiver, and voltage-generation functions. It is commonly used in industrial control, data acquisition, embedded instrumentation, and legacy computer equipment. The verified product information identifies the MAX232DE4 as a 2/2 full RS-232 transceiver in a 16-SOIC package. It operates from a single 4.5 V to 5.5 V supply and supports an operating temperature range of 0 C to 70 C. Additional verified features include operation to 120 kbit/s, low supply current, and ESD protection exceeding 2000 V under the cited JESD test condition. The charge-pump circuit allows the device to generate positive and negative RS-232 levels from one low-voltage supply, avoiding a separate negative power rail. The dual-driver and dual-receiver organization supports two serial channels or a full-duplex link on one device. The receiver converts remote RS-232 signals into logic levels suitable for digital controllers, while the driver boosts local logic signals to RS-232 voltage levels. Typical uses include RS-232 links in test equipment, serial adapters, industrial controllers, point-of-sale systems, and embedded measurement products. The 16-SOIC package supports conventional surface-mount PCB assembly. The verified commercial result lists the part with DigiKey, Mouser, Octopart, and other distributors, but the supplied data does not provide a current unit price or confirmed lead time. For robust implementation, follow the manufacturer datasheet for capacitor selection, pin orientation, and signal-routing requirements. The MAX232DE4 is not a power semiconductor, so SOA data is not applicable. The product should be selected only where the 0 C to 70 C temperature range and the verified electrical limits match the target system requirements. This page combines verified distributor and manufacturer-linked data with application guidance, design considerations, and a package-focused product summary for engineers evaluating RS-232 interface implementations.

Permintaan RFG Kontak
MAX232DG4 - 2/2 RS-232 Transceiver 120kbps | Texas Instruments
MAX232DG4

MAX232DG4 - 2/2 RS-232 Transceiver 120kbps | Texas Instruments

The Texas Instruments MAX232DG4 is a 2/2 full-duplex RS-232 transceiver rated for data rates up to 120 kbit/s, operating from a 4.5 V to 5.5 V single supply in a 16-pin SOIC package. It provides two EIA-232 drivers, two receivers, on-chip charge-pump capacitors, and receiver input protection to ±30 V. An RS-232 transceiver is an interface IC that converts between single-ended digital logic levels and balanced, bipolar EIA-232 signal levels. This level-shifting function belongs to the interface-IC hierarchy and is essential when connecting a 5 V microcontroller, processor, or data terminal to an RS-232 port whose logic levels use positive and negative voltages. Key features include operation from one 4.5 V to 5.5 V supply, integrated 1.0 µF charge-pump capacitors, support for data rates to 120 kbit/s, ±30 V receiver input levels, and low typical supply current of 8 mA. Two driver and two receiver channels allow two communication links or hardware flow-control signals to be implemented in one package. The device is intended for industrial and commercial systems operating from 0°C to 70°C. Technically, the charge-pump circuitry generates the negative voltage required by an RS-232 transmitter from the positive supply. Receivers translate bipolar line voltages into CMOS-compatible logic levels, while the specified ±30 V input tolerance helps manage transient exposure on externally routed cables. Because this is a legacy interface rather than a modern differential bus, grounding, cable routing, and protection remain important system-level concerns. Typical uses include service and test equipment, industrial controllers, point-of-sale equipment, data acquisition systems, and embedded serial-port adapters. The MAX232DG4 is most appropriate where two RS-232 channels are useful and a 5 V supply is available. It is not suitable for voltage-mode RS-485 or RS-422 networks, and its 120 kbit/s maximum data rate is adequate for legacy serial ports rather than high-speed physical-layer protocols. The principal design consideration is charge-pump capacitor placement. The integrated capacitors still require correct bypassing and routing around the device, while protected RS-232 lines should be kept away from clocks and sensitive analog signals. Confirm line direction, connector polarity, and the target baud rate before layout because the package contains both transmitters and receivers. This page consolidates distributor data, cross-reference information, and practical RS-232 design guidance. The MAX232DG4 provides a practical solution for two-channel RS-232 conversion in a compact 16-SOIC. Its integrated charge pump removes the need for external voltage-generation components, while 120 kbit/s operation and ±30 V receiver tolerance make it suitable for established EIA-232 equipment. Designers should still account for cable transients, grounding, baud-rate margin, and connector signal mapping. For systems requiring galvanic isolation, modern differential buses, or operation beyond 120 kbit/s, a different interface architecture is required.

Permintaan RFG Kontak
MAX232DR - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI (Tape & Reel)
MAX232DR

MAX232DR - 5V Dual RS-232 Transceiver, 120kbps, SOIC-16 | TI (Tape & Reel)

The Texas Instruments MAX232DR is a 5V-powered, dual-driver / dual-receiver RS-232 transceiver that integrates an on-board capacitive charge-pump to generate the +/-9V TIA/EIA-232-F signaling voltages from a single 5V supply, delivered in a 16-pin SOIC (D) package. It supports data rates up to 120 kbps, accepts +/-30V input levels on the receiver inputs, and supplies 8 mA typical quiescent current from a 4.5V to 5.5V supply rail. The device is functionally designed to be interchangeable with the industry-standard Maxim MAX232 die. A dual EIA-232 (RS-232) line driver/receiver is an interface IC that bridges TTL/CMOS logic levels (0-5V) and the much higher bipolar voltage swings (+/-5V to +/-15V) required by legacy serial-port standards. By generating these higher rails internally from a single low-voltage supply, dual RS-232 transceivers eliminate the need for a separate negative or high-voltage power rail, simplifying board design and reducing BOM cost. In the broader product hierarchy, the MAX232DR belongs to the EIA-232 transceiver family (RS-232 transceiver), then to the Interface ICs category, then to Integrated Circuits, ultimately serving as an enabler of UART-to-DB9 connectivity in microcontroller- and FPGA-based systems. Key features of the MAX232DR include TIA/EIA-232-F and ITU V.28 compliance, +/-30V receiver input tolerance that survives mis-wired cables and transients, an integrated 5V-to-+/-10V charge pump with four external 1 uF capacitors (charge-pump flying capacitors), two drivers and two receivers in a single 16-pin SOIC package, and ESD protection on the RS-232 bus pins (per the family spec). The 120 kbps data rate is more than adequate for serial console, modem, and industrial telemetry traffic, while the wide 4.5V to 5.5V supply range accommodates standard 5V regulated rails and battery-powered designs with headroom. Architecturally, the charge pump uses a voltage-doubler plus an inverting charge pump clocked from an internal oscillator (typically 125 kHz to 250 kHz range), which provides the +10V and -10V rails that drive the RS-232 output stages. The receivers use Schmitt-trigger inputs with hysteresis for noise immunity on long cables. Compared to using a discrete transistor-based level shifter or a +-12V linear supply, the MAX232DR solution occupies roughly 30 mm x 6 mm of board area and removes one power supply from the design. Typical applications include microcontroller UART-to-RS-232 conversion on serial ports of industrial PLCs, point-of-sale (POS) terminals, embedded debug consoles for firmware development, and legacy PC RS-232 COM ports. The MAX232DR is also commonly deployed in factory automation where 5V microcontrollers need to drive RS-232-controlled motor drives or sensors. Other uses include test and measurement equipment (scopes and analyzers with serial ports), legacy networking gear with DB-9 management ports, and education/development boards (Arduino shield, FPGA dev kit UART bridges). When designing with the MAX232DR, observe charge-pump capacitor polarity: TI recommends 1 uF (or larger) low-ESR ceramic capacitors on each of the four charge-pump pins (C1+, C1-, C2+, C2-, V+, V-). Place the capacitors as close to the IC as possible to minimize parasitic resistance and ringing. Avoid long cable stubs on T1OUT/T2OUT pins, and add TVS diodes for additional ESD protection if the application involves frequent cable mating/unmating. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
MAX232DRE4 - Dual RS-232 Transceiver, 120 kbit/s | TI
MAX232DRE4

MAX232DRE4 - Dual RS-232 Transceiver, 120 kbit/s | TI

Texas Instruments MAX232DRE4 is a dual RS-232 driver/receiver transceiver with two drivers and two receivers, a 4.5 V to 5.5 V single-supply range, and data rates up to 120 kbit/s. It is packaged in a 16-pin SOIC for industrial-control, instrumentation, and legacy serial-interface equipment. An RS-232 transceiver is an interface IC that converts low-voltage TTL or CMOS logic signals into balanced RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, the MAX232 belongs to the RS-232 transceiver family, providing physical-layer conversion for UART, serial-port, and point-to-point communication systems. It simplifies the interface by generating the positive and negative RS-232 voltages from one 5 V supply. The MAX232DRE4 supports operation from 4.5 V to 5.5 V, data rates up to 120 kbit/s, and receiver input levels as high as ±30 V. Its typical supply current is 8 mA, while 500 mV receiver hysteresis improves noise immunity at the logic threshold. The commercial-temperature version operates from 0°C to 70°C and is available in a 16-SOIC package. The device uses charge-pump capacitors to produce the bipolar voltage swings required by RS-232. Its two driver channels translate TTL outputs into RS-232 levels, while its two receiver channels perform the inverse conversion. This architecture suits point-to-point links where full-duplex communication and deterministic logic-level interfacing are required without adding a separate external power-supply circuit. Typical uses include RS-232 ports on industrial controllers, laboratory instruments, barcode readers, data-acquisition equipment, service interfaces, and embedded systems that retain a legacy serial connector. The 120 kbit/s maximum rate provides ample margin for configuration consoles, control commands, firmware downloads, and low-to-moderate-rate telemetry. PCB design should prioritize short connections between the charge-pump capacitors, supply pins, and device ground. Place the required 1.0 µF capacitors close to their associated pins, use a solid ground plane, and keep the RS-232 connector interface area physically separated from sensitive analog circuitry to reduce ESD and surge-related coupling. This page combines electrical specifications, package and application guidance, practical layout considerations, and a structured comparison with verified same-family and cross-brand alternatives. It is intended to help engineers evaluate MAX232DRE4 for a new RS-232 design or determine whether an existing 16-SOIC board can be supported by a pin-compatible replacement.

Permintaan RFG Kontak
MAX232DRG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232DRG4

MAX232DRG4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DRG4 is a 5 V dual RS-232 transceiver IC with two drivers and two receivers, a maximum signaling rate of 120 kbps, and a 16-pin SOIC package. It generates the bipolar RS-232 voltage levels required by EIA/TIA-232 equipment from a single 5 V supply. A RS-232 transceiver is an interface IC that converts between digital logic levels and the bipolar voltage signaling used by serial-port equipment. The MAX232 belongs to the broader line-driver and line-receiver hierarchy, where the driver translates TTL or CMOS logic into RS-232 levels and the receiver converts transmitted RS-232 levels back into logic-compatible signals. This makes it a practical interface between a modern microcontroller UART and legacy RS-232 equipment. The MAX232 provides two transmit channels and two receive channels, allowing one RS-232 port to support full-duplex communication. Its stated maximum data rate is 120 kbps, while its 4.5 V to 5.5 V single-supply operating range supports conventional 5 V digital systems. According to the Texas Instruments product page, the device supports output voltages of positive and negative 9 V and includes positive and negative 2 kV ESD protection on the RS-232 pins. Internal charge-pump circuitry generates the positive and negative voltages required by RS-232 from the 5 V supply, eliminating the need for a separate positive and negative supply in many designs. The drivers and receivers are designed to interface UART controllers with external data-terminal equipment while maintaining logic-compatible digital-side signaling. Its dual-channel arrangement makes it suitable for point-to-point links, equipment control, configuration interfaces, and service ports. Typical uses include industrial controller serial ports, data acquisition systems, test equipment, maintenance interfaces, and communications links between a microcontroller and an RS-232 peripheral. The 120 kbps rate is appropriate for legacy serial protocols rather than high-speed differential buses such as RS-485. Cable length, capacitance, grounding, and signal integrity should be evaluated when designing longer interconnects. For a new layout, route the RS-232 driver outputs and receiver inputs directly to the connector while maintaining the separation recommended for exposed interfaces. Place charge-pump capacitors and interface bypass capacitors close to the device, follow the manufacturer pin description when assigning connector signals, and confirm supply tolerances, grounding, and ESD requirements before releasing the PCB. This page combines manufacturer product information, explicit distributor specifications, package-aware alternatives, and practical interface-design guidance to support component selection, schematic review, PCB implementation, and sourcing decisions for the MAX232DRG4.

Permintaan RFG Kontak
MAX232DW - 120kbps Dual RS-232 Transceiver | Texas Instruments
MAX232DW

MAX232DW - 120kbps Dual RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DW is a dual RS-232 driver and receiver with two drivers, two receivers, a 120 kbit/s data rate, and a 16-pin SOIC package. It operates from a single 5 V supply and uses an on-chip capacitive voltage generator to produce the bipolar voltage levels required by TIA/EIA-232-F interfaces. Its approximately ±9 V driver output and ±2 kV ESD protection make it a standard choice for converting between 5 V TTL/CMOS logic and RS-232 signal levels. An RS-232 transceiver is an interface IC that bridges a digital logic system and a serial communications port using the voltage-defined RS-232 standard. The MAX232 belongs to the RS-232 transceiver hierarchy, where a line driver converts TTL/CMOS inputs into bipolar RS-232 outputs and a line receiver converts bipolar inputs into TTL/CMOS levels. This allows equipment with a 5 V UART or microprocessor interface to communicate with legacy RS-232 ports without implementing discrete level-shifting networks. Key features include two transmit channels, two receive channels, operation to 120 kbit/s, a typical 8 mA supply current, receiver input capability of ±30 V, and compatibility with TIA/EIA-232-F and ITU Recommendation V.28. The receiver has a typical transition threshold of 1.3 V and typical hysteresis of 0.5 V. These characteristics provide noise margin and stable interpretation of the bipolar RS-232 signal while retaining the familiar ±9 V driver levels. The device combines four RS-232 signal-conditioning channels with an on-chip charge-pump voltage generator. Charge-pump capacitors connected to the designated voltage-generator pins create the positive and negative supply levels needed by the drivers. This architecture eliminates the negative power supply otherwise required by many discrete RS-232 implementations, while the receiver side provides the electrical translation needed to protect and interface a 5 V logic device. Typical uses include industrial serial consoles, point-of-sale equipment, data-acquisition systems, test and measurement instruments, service interfaces, and legacy peripheral connections. A microcontroller can connect its UART TX and RX signals to the appropriate driver and receiver channels, while the external RS-232 connector receives the bipolar line outputs. The 120 kbit/s capability covers many legacy control and communications protocols without requiring a high-speed RS-485 interface. The principal design consideration is the charge-pump capacitor network and RS-232 connector routing. Capacitors must be connected exactly as required by the manufacturer datasheet, and external line protection should be evaluated for the target cable length and environment. Logic levels and signal polarity must also be checked at each UART channel because the MAX232 provides level conversion, not automatic inversion or protocol handling. This product page consolidates the verified manufacturer specifications, distributor availability, cross-reference information, and engineering guidance for MAX232DW. It also distinguishes a genuine same-package replacement from devices with different charge-pump capacitor requirements or package dimensions, helping engineers avoid substitutions that require PCB or component changes.

Permintaan RFG Kontak
MAX232DWE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments
MAX232DWE4

MAX232DWE4 - Dual 120kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX232DWE4 is a dual RS-232 transceiver containing two EIA-232 drivers and two receivers, operating from a single 5 V supply in a 16-SOIC package. It supports data rates up to 120 kbit/s, accepts receiver input levels of ±30 V, and uses 1.0-mF charge-pump capacitors. The device is recommended for V.28 interfaces and provides 8 mA typical supply current. An RS-232 transceiver is an interface IC that converts between digital logic levels and the voltage-domain signals used by RS-232 equipment. The MAX232 belongs to the RS-232 transceiver hierarchy within interface ICs and broader semiconductor signal-conditioning devices. Its transmitters boost logic signals to RS-232 levels, while its receivers convert bipolar RS-232 inputs into logic-compatible outputs. This makes the device suitable for connecting older serial equipment, control systems, and industrial peripherals to microcontrollers or microprocessors. Key features include two driver channels, two receiver channels, operation from a single 5 V supply, and data-rate support up to 120 kbit/s. The receiver input can withstand ±30 V levels, which improves compatibility with RS-232 ports that may expose unused or externally connected signal lines. According to the manufacturer datasheet, ESD protection exceeds the JESD 2000-V human-body-model requirement. The commercial temperature designation is 0°C to 70°C. The MAX232 uses an on-chip charge-pump voltage converter to generate the positive and negative voltages required by RS-232 drivers from the single 5 V supply. External charge-pump capacitors support this conversion, allowing the complete interface to fit in a standard 16-SOIC footprint. Two drivers and two receivers provide four active interface channels in one package, reducing board area compared with discrete level-shifters and simplifying software control of multiple serial lines. Typical applications include RS-232 console connections, industrial serial adapters, point-of-sale equipment, test and measurement instrumentation, and legacy peripheral interfaces. The 120 kbit/s capability is suitable for moderate-speed serial links rather than high-bandwidth data protocols. Its integrated two-channel transmit and receive arrangement also fits systems that require bidirectional communication over two RS-232 ports. PCB layout should keep charge-pump capacitors close to their associated pins, provide a low-impedance ground connection, and route driver outputs away from sensitive receiver inputs. Confirm the logic levels of the connected host because RS-232 voltage levels are bipolar and not directly compatible with 3.3 V or 5 V CMOS inputs. The 16-SOIC package requires adequate clearance around the exposed leads for soldering and inspection. This page combines the device specifications, commercial sourcing information, verified drop-in alternatives, interface comparisons, and practical PCB guidance to support faster component selection and implementation.

Permintaan RFG Kontak