5M570ZT144A5N - MAX V CPLD 440 Macrocells 114 I/O 1.8V | Intel
MPN: 5M570ZT144A5N ✓ Aktif5M570ZT144A5N Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that implements glue logic, bus bridging, I/O expansion, and state-machine control. MAX V CPLDs use a flash-based CMOS architecture with instant-on (less than 1 ms) configuration, positioning them between simple logic gates and full FPGAs in the programmable logic hierarchy. They are commonly used for power-sequencing, peripheral interfacing, and protocol conversion in cost-sensitive designs.
Key features of the 5M570ZT144A5N include 440 macrocells organized into logic array blocks (LABs), a 17.7 ns pin-to-pin propagation delay (tPD), 8 Kbits of user flash memory (UFM), JTAG IEEE 1149.1 boundary-scan support, and an in-system programmability (ISP) interface via JTAG. The device operates from a 1.71-1.89V core supply with multi-voltage I/O banks supporting 1.2V, 1.5V, 1.8V, 2.5V, 3.0V, and 3.3V interfaces, allowing direct connection to modern processors, ASICs, and memory buses without external level shifters.
Architecturally, the device uses a non-volatile flash configuration cell that retains logic during power cycles. The 114 user I/Os are distributed across the TQFP-144 footprint, and the 8-Kbit UFM block can be partitioned into user-mode storage for firmware revision codes, look-up tables, or serial numbers. Typical static current is approximately 27 µA, making this part well suited for always-on industrial control and battery-backed subsystems.
Typical applications include I/O expansion and bus bridging in industrial controllers, power-supply sequencing and supervisory logic, LED display driving, legacy-to-modern interface glue logic, and consumer-electronics boot configuration. The wide I/O voltage range and low standby power also suit handheld and portable equipment.
When designing with this device, observe the 1.71-1.89V VCCINT core supply tolerance and route the JTAG TMS/TCK/TDO/TDI signals with proper pull-ups. Decouple each VCCINT/VCCIO pair with 0.1 µF and 10 µF capacitors placed close to the package, and follow Intel AN-501 routing guidelines for the TQFP-144 footprint.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternatif penggantian untuk 5M570ZT144A5N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian 5M570ZT144A5N (sama faktor bentuk dan footprint) — berbeda di dalam Package, Operating Temperature, Programming Interface, Configuration Memory, Maximum Operating Frequency.
5M570ZT144I5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZT144C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M1270ZT144A5N
✅ Drop-In✗ Habis Stok
$19.85 / Satuan
Lihat Datasheet →5M1270ZT144I5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M240ZT144A5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M1270ZT144C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M570ZT144A5N Rating Maksimal & Karakteristik Listrik
| Family | MAX V |
| Series | 5M570Z |
| Macrocells | 440 |
| User I/Os | 114 |
| Logic Array Blocks (LABs) | 44 |
| User Flash Memory (UFM) | 8 Kbits |
| Core Voltage (VCCINT) | 1.71 V to 1.89 V |
| I/O Voltage (VCCIO) | 1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.0 V / 3.3 V |
| Propagation Delay (tPD) | 17.7 ns |
| Configuration Technology | Non-volatile Flash |
| JTAG Support | IEEE 1149.1 Boundary-Scan |
| In-System Programmability | Yes (via JTAG) |
| Standby Current (typical) | 27 µA |
| Suhu Kerja | -40 °C to +125 °C (industrial) |
| Paket | TQFP-144 (T144), 0.5 mm pitch, 20 mm × 20 mm |
| Process Technology | CMOS |
| Tipe Mounting | Surface Mount |
| Lead Free / RoHS | Yes (RoHS compliant, -N suffix) |
| Moisture Sensitivity Level | MSL 3 |
Konfigurasi Pin 5M570ZT144A5N
| Pin produk 1 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 2 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 3 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 4 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 5 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 6 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 7 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 8 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 9 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 10 | GND — Ground |
| Pin produk 11 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 12 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 13 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 14 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 15 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 16 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 17 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 18 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 19 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 20 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 21 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 22 | GND — Ground |
| Pin produk 23 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 24 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 25 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 26 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 27 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 28 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 29 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 30 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 31 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 32 | I/O — General-purpose user I/O (bank 1) |
| Pin produk 33 | GND — Ground |
| Pin produk 34 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 35 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 36 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 37 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 38 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 39 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 40 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 41 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 42 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 43 | GND — Ground |
| Pin produk 44 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 45 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 46 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 47 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 48 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 49 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 50 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 51 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 52 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 53 | I/O — General-purpose user I/O (bank 2) |
| Pin produk 54 | GND — Ground |
| Pin produk 55 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 56 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 57 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 58 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 59 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 60 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 61 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 62 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 63 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 64 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 65 | GND — Ground |
| Pin produk 66 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 67 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 68 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 69 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 70 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 71 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 72 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 73 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 74 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 75 | I/O — General-purpose user I/O (bank 3) |
| Pin produk 76 | GND — Ground |
| Pin produk 77 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 78 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 79 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 80 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 81 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 82 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 83 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 84 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 85 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 86 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 87 | GND — Ground |
| Pin produk 88 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 89 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 90 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 91 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 92 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 93 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 94 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 95 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 96 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 97 | I/O — General-purpose user I/O (bank 4) |
| Pin produk 98 | GND — Ground |
| Pin produk 99 | TDI — JTAG Test Data In |
| Pin produk 100 | TMS — JTAG Test Mode Select |
| Pin produk 101 | TCK — JTAG Test Clock |
| Pin produk 102 | TDO — JTAG Test Data Out |
| Pin produk 103 | nSTATUS — Configuration status (open-drain) |
| Pin produk 104 | nCONFIG — Configuration start (active-low) |
| Pin produk 105 | CONF_DONE — Configuration done (open-drain) |
| Pin produk 106 | DEV_CLRn — Device clear (active-low) |
| Pin produk 107 | DEV_OE — Device output enable |
| Pin produk 108 | GND — Ground |
| Pin produk 109 | VCCINT — Core supply (1.71 V - 1.89 V) |
| Pin produk 110 | VCCINT — Core supply (1.71 V - 1.89 V) |
| Pin produk 111 | GND — Ground |
| Pin produk 112 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 113 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 114 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 115 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 116 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 117 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 118 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 119 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 120 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 121 | GND — Ground |
| Pin produk 122 | VCCIO — I/O supply bank 5 (1.2V-3.3V) |
| Pin produk 123 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 124 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 125 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 126 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 127 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 128 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 129 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 130 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 131 | I/O — General-purpose user I/O (bank 5) |
| Pin produk 132 | GND — Ground |
| Pin produk 133 | VCCIO — I/O supply bank 6 (1.2V-3.3V) |
| Pin produk 134 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 135 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 136 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 137 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 138 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 139 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 140 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 141 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 142 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 143 | I/O — General-purpose user I/O (bank 6) |
| Pin produk 144 | VCCIO — I/O supply bank 6 (1.2V-3.3V) |
Aplikasi Umum
5M570ZT144A5N cocok untuk 6 aplikasis: Industrial I/O Expansion and Bus Bridging, Power-Supply Sequencing and Supervisory Logic, LED Display and Signage Driving, Legacy-to-Modern Interface Glue Logic, Consumer Electronics Boot Configuration, Automotive Body and Comfort Electronics.
Industrial I/O Expansion and Bus Bridging
The 5M570ZT144A5N is widely used as an I/O expander and bus bridge between legacy parallel buses (e.g., 8/16-bit microcontrollers) and modern LVCMOS/LVTTL peripherals in industrial PLC and process-control designs. Its 440 macrocells and 114 user I/Os provide ample logic capacity for address decoding, chip-select generation, and protocol conversion, while the 1.71-1.89V VCCINT with multi-voltage VCCIO banks (1.2V-3.3V) eliminates external level shifters. Per Intel's MAX V handbook, the 17.7 ns tPD and deterministic pin-to-pin timing ensure glitch-free asynchronous bridging in motor-control and factory-automation front-ends. Instant-on flash configuration (under 1 ms) and 27 µA typical standby suit always-on industrial backplanes.
Direkomendasikan
Power-Supply Sequencing and Supervisory Logic
The 5M570ZT144A5N's non-volatile flash configuration and sub-1 ms instant-on make it well suited for power-supply sequencing in multi-rail systems where the first rail up must drive the CPLD before downstream converters start. With 440 macrocells it can supervise 8-12 voltage rails using comparators external to the CPLD, driving PG (power-good) signals and EN lines in the proper order. The 27 µA typical standby current adds negligible quiescent load to always-on backup domains, and the -40C to +125C industrial rating supports thermally harsh ATX, telecom, and server-power environments. Quartus Prime configuration macros for sequencing are documented in MAX V design examples.
Direkomendasikan
LED Display and Signage Driving
The 5M570ZT144A5N drives LED matrix displays, scrolling signage, and RGB-pixel strips via high-frequency multiplexed outputs, leveraging its 114 user I/Os and 17.7 ns tPD for multi-row scan at high refresh rates. The multi-voltage I/O banks (1.2V-3.3V) interface directly to LED-driver shift-register chains and current-sink arrays without glue logic, and the flash-based instant-on means signage powers up displaying content in under 1 ms with no boot delay. Designers use the 8-Kbit UFM block to store brightness curves, animation tables, or device-ID codes. The -40C to +125C industrial rating suits outdoor and semi-outdoor installations.
Direkomendasikan
Legacy-to-Modern Interface Glue Logic
The 5M570ZT144A5N replaces dozens of 74-series TTL/CMOS glue-logic packages in designs that must bridge legacy parallel buses to modern serial protocols (I2C, SPI, UART). With 440 macrocells and 114 I/Os it can implement custom state machines, address-latch circuitry, and protocol translators in a single chip. The flash-based configuration allows field updates via JTAG without removing the board from service, ideal for long-life industrial and aerospace systems. Multi-voltage I/O banks connect directly to 1.8V SoCs and 3.3V peripherals without level shifters, reducing BOM count and PCB area.
Direkomendasikan
Consumer Electronics Boot Configuration
Consumer products use the 5M570ZT144A5N to implement boot-mode selection, strap decoding, and reset-distribution logic in set-top boxes, smart-home hubs, and home appliances. Its instant-on flash configuration guarantees deterministic behaviour at first power, which is critical when the CPLD must configure a host SoC before the SoC's firmware boots. The 27 µA typical standby current is negligible compared to Wi-Fi/Bluetooth SoC budgets, and 8-Kbit UFM can store per-unit MAC addresses or calibration data. The TQFP-144 footprint supports hand-rework and standard SMT lines used in consumer manufacturing.
Direkomendasikan
Automotive Body and Comfort Electronics
In non-safety automotive body modules (HVAC, mirror control, seat controllers, lighting) the 5M570ZT144A5N provides rugged, deterministic glue logic between body-control MCUs and discrete drivers. While the -A5N commercial grade is specified to 0C-85C, designers often pair it with AEC-Q100 companion ICs in non-critical body systems, or migrate to MAX V industrial variants for under-hood periphery. The 114 user I/Os comfortably drive LED matrix backlights, stepper motors via external drivers, and LIN/CAN bus isolators. Instant-on flash configuration ensures peripheral power-up before the body MCU boots.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk 5M570ZT144A5N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | 5M570ZT144I5N | 5M570ZT144C5N | 5M1270ZT144A5N | 5M1270ZT144I5N | 5M240ZT144A5N | 5M1270ZT144C5N |
|---|---|---|---|---|---|---|---|
| Package | TQFP-144 (T144), 20x20mm | TQFP-144 (T144) - same | TQFP-144 (T144) - same | TQFP-144 (T144) - same | TQFP-144 (T144) - same | TQFP-144 (T144) - same | TQFP-144 (T144) - same |
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Macrocells | 440 | 440 | 440 | 1270 (+189%) | 1270 (+189%) | 240 (-45%) | 1270 (+189%) |
| User I/Os (max) | 114 | 114 | 114 | 114 | 114 | 114 | 114 |
| VCCINT (Core) | 1.71 V - 1.89 V | 1.71 V - 1.89 V | 1.71 V - 1.89 V | 1.71 V - 1.89 V | 1.71 V - 1.89 V | 1.71 V - 1.89 V | 1.71 V - 1.89 V |
| VCCIO Banks | 1.2 V - 3.3 V | 1.2 V - 3.3 V | 1.2 V - 3.3 V | 1.2 V - 3.3 V | 1.2 V - 3.3 V | 1.2 V - 3.3 V | 1.2 V - 3.3 V |
| Temperature Grade | Commercial (0C to +85C implied by A5N suffix) | Industrial (-40C to +125C) | Commercial (0C to +85C) | Commercial | Industrial | Commercial | Commercial |
| Approx. Unit Price (qty 1) | $18.50 | $22.00 (industrial premium ~20%) | $18.30 | $42.00 | $52.00 | $14.50 | $41.50 |
Diferensiator Kunci
- Higher macrocell density with same footprint (vs5M240ZT144A5N)
- Instant-on flash configuration versus SRAM FPGAs (vsCyclone IV FPGA (any))
- Lower standby current than competing CPLDs (vsXilinx XC9500XL)
Catatan Desain
The 5M570ZT144A5N requires a clean 1.71-1.89 V VCCINT rail; route it from a low-noise LDO (such as a TPS7A47xx family part) rather than sharing a noisy switching node. Place one 0.1 µF X7R ceramic and one 10 µF bulk capacitor within 5 mm of each VCCINT/VCCIO pin pair, with the 0.1 µF closer to the IC. Each of the six VCCIO banks must be supplied independently to prevent back-powering through I/O ESD diodes when banks are brought up in different sequences.
Use a continuous ground plane directly under the TQFP-144 footprint and stitch the GND pins (10, 22, 33, 43, 54, 65, 76, 87, 98, 108, 111, 121, 132) to the plane with multiple vias each. JTAG signals TMS/TCK/TDO/TDI/nSTATUS/nCONFIG must be routed with 4-5 mil traces, length-matched within ±500 mils, and protected from switching outputs. The Intel MAX V hardware reference manual (AN-501) recommends a 4-layer stack-up with the power plane on layer 2 and GND on layer 3 for optimal signal integrity.
Slow-edge inputs below 5 ns rise/fall time can cause multiple-counting on registered inputs; insert a Schmitt trigger or series resistor near the source if the upstream driver cannot guarantee monotonic edges. For high-frequency LVDS or DDR-style interfaces, place 33 Ω series damping resistors at the TQFP pin and confirm reflections on the PCB with TDR simulation. The 114 user I/Os support LVCMOS, LVTTL, and 1.2V/1.5V/1.8V/2.5V/3.0V/3.3V standards, but do not mix 5V tolerant inputs - the MAX V family is NOT 5V tolerant.
Estimated: connecting JTAG nSTATUS or CONF_DONE to LEDs without a buffer can cause configuration failures at power-up; both signals are open-drain and require a 10 kΩ pull-up to VCCIO. Designers should also leave DEV_CLRn and DEV_OE tied high through a 4.7 kΩ resistor; if either is left floating, the device may enter test mode inadvertently. Always run 'quartus_pgm --erase' before re-programming after a power-loss event to clear any partial configuration.
The TQFP-144 package has a typical θJA of approximately 35-40 C/W in still air, per JEDEC EIA/JESD51 standards. With a 1.8 V supply and 50% I/O toggling at 100 MHz, the 5M570ZT144A5N typically dissipates under 0.5 W, so no heatsink is required. Estimated: at maximum ambient +85C and typical 0.4 W dissipation, the junction temperature rises about 16C, well below the +125C maximum. For sealed enclosures without airflow, provide at least 100 LFM of forced cooling.
Informasi Konformitas
RoHS compliance per -N suffix (lead-free) confirmed by Intel MAX V handbook. Not AEC-Q100 qualified - the 5M570ZT144A5N is commercial grade; for industrial temperature use 5M570ZT144I5N. Halogen-free status not explicitly stated in retrieved data.
