ATSAMD21J15B-AU - 48MHz Cortex-M0+ 32KB Flash MCU | Microchip
MPN: ATSAMD21J15B-AU ✓ AktifATSAMD21J15B-AU Ringkasan
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ATSAMD21J15B belongs to the SAM D21 family, which sits within the hierarchy of embedded processors, microcontrollers, and embedded semiconductors. Its Arm Cortex-M0+ core provides efficient 32-bit instruction processing while avoiding the resource demands of higher-performance application processors.
The ATSAMD21J15B-AU combines 32 KB of Flash with 4 KB of SRAM and supports operation from a 3.3 V supply. Its documented feature set includes a single-cycle hardware multiplier, power-on reset, an Event System for peripheral-to-peripheral signaling, and support for capacitive-touch buttons, sliders, and wheels. These resources make it suitable for compact human-interface, control, sensing, and connected embedded products.
Its peripheral architecture includes communication and timing functions suited to industrial control, consumer interfaces, and compact embedded nodes. The 64-pin package exposes more interface options than smaller microcontroller packages, while the 48 MHz operating frequency supports responsive event handling and control-loop execution. The manufacturer's product page identifies the device as a general-purpose, low-power SAM D21-series member with an Arm Cortex-M0+ processor.
Typical uses include capacitive-touch control panels, building-access terminals, compact sensor hubs, industrial interface modules, and embedded communications equipment. In these applications, the Event System can reduce peripheral coupling by allowing signals to be routed internally, while the SRAM and Flash allocation supports compact control firmware, calibration data, and application logic.
Board design should preserve the recommended power, decoupling, clock, and programming arrangements in the manufacturer datasheet. Because the package provides 64 pins, verify every signal against the exact pin-description table before routing the PCB. Use the 3.3 V operating supply consistently across the digital domain and confirm external peripheral voltage levels before connecting them directly to the microcontroller.
This page combines the manufacturer's device description with drop-in candidate analysis, a package-aware comparison, and practical design guidance for engineers evaluating the ATSAMD21J15B-AU. The alternatives are limited to devices for which the available cross-reference information supports the same 64-TQFP footprint; each candidate still requires board-level and firmware verification before substitution.
Alternatif penggantian untuk ATSAMD21J15B-AU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ATSAMD21J15B-AU (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Package.
ATSAMD21J15A-AU
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ATSAMD21J15B-AUT
✅ Drop-InKontak untuk harga
Lihat Datasheet →ATSAMD21J15B-CN
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
ATSAMD21J15B-AU Rating Maksimal & Karakteristik Listrik
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Processor Core | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB |
| Program Memory Organization | 32K x 8 bits |
| SRAM | 4 KB |
| Architecture | 32-bit |
| Tegangan Pemuat Kerja | 3.3 V |
| Paket | 64-pin TQFP, 10 mm x 10 mm |
| Tipe Mounting | Surface mount |
| Suhu Kerja | -40°C to +85°C |
| Green Package | Yes |
| Hardware Multiplier | Single-cycle |
| Programmable Memory | 32 KB in-system self-programmable Flash |
| Reset Features | Power-on reset (POR) |
| Peripheral Interconnect | Event System |
| Capacitive Touch Support | Buttons, slider, and wheel user interfaces |
| Functional Safety | Functional Safety (FuSa) device |
ATSAMD21J15B-AU yes Diamant Konfigurasi Panduan
Konfigurasi pin untuk ATSAMD21J15B-AU (yes pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk ATSAMD21J15B-AU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ATSAMD21J15B-AU cocok untuk 6 aplikasis: Capacitive Touch Control Panels, Industrial Sensor Hubs, Building Access Terminals, Compact Communications Modules, Low-Power Embedded Control, Embedded IoT Control Nodes.
Capacitive Touch Control Panels
The ATSAMD21J15B-AU fits touch controls because its manufacturer documentation identifies support for capacitive-touch buttons, sliders, and wheel interfaces. The 48 MHz Arm Cortex-M0+ core can scan touch inputs, apply filtering, update display or relay commands, and communicate the result. Its 32 KB Flash and 4 KB SRAM provide room for compact acquisition and user-interface firmware. The Event System can also coordinate touch events with timers and other peripherals without relying entirely on central interrupt servicing. Board-level work should follow the manufacturer guidance for electrode routing, guard rings, filtering, and grounding.
Direkomendasikan
Industrial Sensor Hubs
The ATSAMD21J15B-AU is suitable for a compact industrial sensor hub that gathers digital inputs and manages local sensing functions. Its 32-bit Cortex-M0+ processor operates up to 48 MHz, providing enough performance for sensor polling, threshold logic, filtering, diagnostics, and a communication stack within 32 KB Flash and 4 KB SRAM. The 64-pin TQFP package also offers more peripheral routing options than a compact 20-pin device. For reliable deployment, validate timing margins, input levels, isolation boundaries, and operating-temperature requirements for the complete controller assembly.
Direkomendasikan
Building Access Terminals
The ATSAMD21J15B-AU can serve as the controller in a building-access terminal combining keypad or touch input, status indication, and a local serial interface. Its 48 MHz Cortex-M0+ core supports responsive event handling, while 32 KB Flash accommodates firmware for credential processing, keypad scanning, and diagnostics. The Event System supports structured peripheral interactions, helping coordinate timers, communication, and indicator outputs. Because terminals may operate near noisy motors and long cables, the design should include appropriate ESD protection, defined grounding, watchdog recovery, and careful separation of communication and power routing.
Direkomendasikan
Compact Communications Modules
The ATSAMD21J15B-AU is appropriate for a compact communications module that performs protocol handling, local buffering, and user-interface updates. The Cortex-M0+ architecture executes 32-bit instructions at up to 48 MHz, while the Event System can route signals among communication and timing peripherals. Its 4 KB SRAM and 32 KB Flash suit concise network stacks, protocol parsers, and application state. The exact peripheral mix and pin multiplexing must be checked against the device documentation, and a production module should preserve brownout handling, clock stability, and firmware-update provisions across the full -40°C to +85°C range.
Direkomendasikan
Low-Power Embedded Control
The ATSAMD21J15B-AU is a practical choice for low-power embedded control because the manufacturer classifies the SAM D21J as a low-power general-purpose microcontroller. Its Cortex-M0+ core provides efficient 32-bit processing without the overhead of a high-performance application processor, and the 64-pin package exposes a broad selection of I/O for actuators, sensors, and local interfaces. Software can use peripheral event routing and low-power modes to reduce activity between external events. Final energy performance depends on clock configuration, peripheral loading, sleep modes, and the leakage profile of the complete board.
Direkomendasikan
Embedded IoT Control Nodes
The ATSAMD21J15B-AU can serve as the local control node in an IoT product that handles sensors, touch input, and a network-facing peripheral. The 48 MHz processor supports responsive foreground tasks, while 32 KB Flash and 4 KB SRAM fit compact protocol code and control state. Its Event System is useful for coordinating asynchronous peripheral activity, including timers and communication events. Designers should reserve pins for programming and recovery, implement a robust watchdog strategy, and confirm that the selected wireless or wired interface has compatible voltage levels and timing requirements.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ATSAMD21J15B-AU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ATSAMD21J15A-AU | ATSAMD21J15B-AUT | ATSAMD21J15B-CN |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) | 64-TQFP (10x10) |
| Processor Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Programmable Memory Type | 32 KB in-system self-programmable Flash | 32 KB in-system self-programmable Flash | 32 KB in-system self-programmable Flash | 32 KB in-system self-programmable Flash |
| Peripheral Interconnect | Event System | Event System | Event System | Event System |
| New-Design Status | B revision preferred for new designs | Not recommended for new designs | Related B-revision ordering code | Related B-revision ordering code |
Diferensiator Kunci
- Preferred B revision for new SAM D21J designs (vsATSAMD21J15A-AU)
- Broad interface access in a compact 64-pin package (vsATSAMD21J15A-AU)
- Event-driven peripheral architecture (vsATSAMD21J15B-CN)
Catatan Desain
Build the PCB footprint from the manufacturer package drawing for the 64-pin TQFP rather than relying on a generic 64-pin library symbol. Confirm the 10 mm by 10 mm body, lead span, pitch, and recommended land pattern. Preserve access to programming and debug signals, and place decoupling capacitors adjacent to the appropriate supply pins to minimize supply-impedance paths and keep switching transients away from sensitive analog or communication nodes.
Design the 3.3 V supply path for both startup and transient requirements. Include local high-frequency decoupling at the MCU supply pins, maintain a defined return path, and account for voltage droop during peripheral activity. If external devices use another voltage domain, use appropriately rated level shifting instead of assuming the ATSAMD21J15B-AU pins are 5 V tolerant. Validate brownout, reset, and power-sequencing behavior across the full -40°C to +85°C range.
Do not substitute ATSAMD21J15A-AU into a new design without checking the change notice and firmware support. Although it uses the same 64-TQFP family format and closely matches the core, memory, and speed configuration, the manufacturer identifies the A revision as not recommended for new designs. Also check alternate-function multiplexing, peripheral instance assignments, and package-specific pin names before using an ordering-code variant as a production replacement.
Separate sensitive signal paths from switching nodes and high-current return paths. The Event System can reduce software coupling between peripherals, but it does not remove PCB-level interference concerns. Use a continuous ground reference where practical, keep clock and communication traces short, and place external protection close to connectors or exposed interfaces. For capacitive-touch designs, follow the manufacturer's electrode and guard-layout guidance because copper and enclosure geometry can alter sensitivity.
Informasi Konformitas
The manufacturer describes ATSAMD21J15A-AU as not recommended for new designs and recommends ATSAMD21J15B. The ATSAMD21J15B-AU listing identifies a green package, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration was established.