LM2902VDG - Quad 3-32V Op Amp | onsemi | Industrial Control
MPN: LM2902VDG ✓ AktifLM2902VDG Ringkasan
An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its differential inputs. The quad configuration places four independent amplifiers in one package, reducing board area in multi-channel sensor, filter, comparator, and feedback-control designs. The LM2902 series supports single-supply or split-supply operation, which allows the same device architecture to be used in circuits powered by one positive rail or by positive and negative rails.
Key characteristics include four amplifier circuits in one 14-SOIC package, true differential inputs, single-supply operation, and an extended-temperature positioning used for demanding industrial applications. Because the package contains four independent amplifiers, each channel can perform a separate function without requiring multiple single-amplifier packages. Stable operation without external compensation simplifies designs requiring unity-gain voltage followers, comparators, summing amplifiers, transimpedance stages, and active filters.
The LM2902 belongs to the low-cost, general-purpose operational-amplifier category, combining transistor-level input stages, differential amplification, frequency compensation, and output-drive capability in a compact analog IC. Its 3 V to 32 V supply capability is particularly useful in industrial systems where the amplifier must interface with sensor signals and actuator-control circuitry operating from elevated positive rails. The wide supply range should not be interpreted as permission to exceed the limits of the particular operating-temperature grade or to operate without checking absolute-maximum ratings.
Typical applications include current-loop and voltage-loop sensing, low-side transducer amplification, programmable-control interfaces, sensor conditioning, industrial data acquisition, audio and communications buffers, and four-channel active filtering. For bridge sensors, the differential input arrangement helps reject common-mode voltage while amplifying the smaller bridge differential signal. In comparator service, output saturation timing should be checked at the actual load and supply voltage because the LM2902 is a general-purpose amplifier rather than a dedicated high-speed comparator.
When laying out a design, keep sensitive input and feedback traces short, place input-biasing or compensation networks close to their associated pins, and avoid long paths adjacent to switching nodes. Single-supply applications must also account for input and output common-mode limits. If the source can approach ground or the positive rail, use a suitable biasing arrangement or a rail-to-rail input amplifier instead of assuming full-swing operation. The manufacturer datasheet remains the controlling reference for electrical limits, pin functions, and test conditions.
This page combines the LM2902VDG ordering information with same-package replacement guidance and application-focused engineering guidance. It is intended to help engineers identify the correct quad amplifier package, compare genuine drop-in options, and plan the PCB and signal-conditioning implementation before ordering.
Alternatif penggantian untuk LM2902VDG — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian LM2902VDG (sama faktor bentuk dan footprint) — berbeda di dalam Package, Amplifier Type, Maximum Supply Voltage, Input Offset Voltage, Number of Amplifier Channels.
LM2902DG
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902D
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902NSR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902DG4
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902KPWR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902VDR2
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM2902VDG Rating Maksimal & Karakteristik Listrik
| Number of Amplifier Circuits | 4 circuits |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 32 V |
| Power Supply Type | Single supply |
| Input Type | True differential input |
| Amplifier Configuration | Quad operational amplifier |
| Paket | 14-SOIC |
| Tipe Mounting | Surface mount |
| Internal Frequency Compensation | Frequency compensated |
Konfigurasi Pin LM2902VDG
| Pin produk 1 | OUT1 — Output of amplifier 1 |
| Pin produk 2 | IN1- — Inverting input of amplifier 1 |
| Pin produk 3 | IN1+ — Non-inverting input of amplifier 1 |
| Pin produk 4 | GND — Ground connection |
| Pin produk 5 | IN2+ — Non-inverting input of amplifier 2 |
| Pin produk 6 | IN2- — Inverting input of amplifier 2 |
| Pin produk 7 | OUT2 — Output of amplifier 2 |
| Pin produk 8 | OUT3 — Output of amplifier 3 |
| Pin produk 9 | IN3- — Inverting input of amplifier 3 |
| Pin produk 10 | IN3+ — Non-inverting input of amplifier 3 |
| Pin produk 11 | V+ — Positive supply connection |
| Pin produk 12 | IN4+ — Non-inverting input of amplifier 4 |
| Pin produk 13 | IN4- — Inverting input of amplifier 4 |
| Pin produk 14 | OUT4 — Output of amplifier 4 |
Aplikasi Umum
LM2902VDG cocok untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Current-to-Voltage Measurement, Low-Side Power Feedback, Active Filtering and Buffering, Audio and Communication Buffers, Data Acquisition and Control Loops.
Industrial Sensor Signal Conditioning
The LM2902VDG fits industrial sensor conditioning because its four true-differential-input amplifiers can process four channels while operating from a 3 V to 32 V supply. Use each channel around a Wheatstone bridge, resistive sensor, or low-level transducer to amplify the differential sensor voltage and reject common-mode disturbance. Place the amplifier near the sensor source, bias the input pair within the datasheet common-mode range, and route the differential pair as a matched pair. The quad package reduces component count, while its extended-temperature positioning supports industrial designs that must tolerate temperature variation. Confirm output-swing limits when the sensor can approach either supply rail.
Direkomendasikan
Current-to-Voltage Measurement
The LM2902VDG can implement four independent current-to-voltage measurements in instrumentation and power-control systems. Each amplifier works with a sense resistor, with the amplifier voltage gain set by feedback components and the input common-mode voltage kept within the manufacturer limits. Its 3 V minimum operating supply supports compact 3.3 V and 5 V systems, while the 32 V maximum provides headroom for higher industrial rails. A quad package simplifies routing because all four channels share the same positive supply and ground. Check the exact input offset and bias-current specifications before setting a low-value sense resistor, because those errors can dominate the measurement.
Direkomendasikan
Low-Side Power Feedback
The LM2902VDG is appropriate for amplifying the voltage across a low-side current shunt in motor, power-supply, and battery-management feedback loops. The true-differential input arrangement reduces sensitivity to ground offsets between the shunt and amplifier ground, provided the common-mode voltage remains within the operating range. Use a Kelvin connection to the shunt and keep feedback resistors close to the relevant amplifier channel. Because one package contains four independent amplifiers, it can monitor several rails or implement the error amplifier, current sensor, and auxiliary signal conditioning stages. The 3 V to 32 V supply range accommodates both low-voltage portable systems and nominal 24 V industrial controls.
Direkomendasikan
Active Filtering and Buffering
The four internally compensated channels in the LM2902VDG support multiple active-filter and buffering functions within one package. It can be used for unity-gain voltage followers, smoothing stages, gain blocks, and multichannel low-pass filters where the required bandwidth remains within the amplifier's specified performance. The 3 V to 32 V operating range permits the same quad topology to serve 3.3 V, 5 V, 12 V, and 24 V rails. Place each feedback network close to its associated output, avoid sharing long high-impedance paths between channels, and use a solid ground reference. Validate stability, output swing, and channel interaction against the final signal amplitude and load.
Direkomendasikan
Audio and Communication Buffers
The LM2902VDG can provide low-cost buffering and gain stages for microphone preamplifiers, line-level interfaces, communications, and audio accessory circuits. Its true-differential inputs suit balanced sources, while the single-supply capability simplifies systems using a positive rail and a midpoint reference. Bias bipolar signal sources around the midpoint so their peaks remain inside the input common-mode range. The quad configuration allows simultaneous use for input buffering, active gain, output isolation, and auxiliary filtering. Designers should check the exact bandwidth, slew rate, output drive, output-voltage swing, and noise-related parameters in the onsemi electrical-characteristics table before using it in high-fidelity or high-speed paths.
Direkomendasikan
Data Acquisition and Control Loops
The LM2902VDG is useful in compact data-acquisition and industrial-control modules requiring several analog channels. Four amplifiers can convert sensor outputs, drive control-loop error amplifiers, buffer a reference, and condition a monitor signal from one 14-SOIC package. Its operating supply range of 3 V to 32 V allows deployment near both 3.3 V digital electronics and 24 V industrial interfaces. Keep the analog section physically separated from switching regulators and relay drivers, provide local supply bypassing, and use short feedback paths. For multiplexed or high-impedance sources, add the necessary isolation resistance and account for amplifier bias current to prevent channel-to-channel crosstalk and settling errors.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LM2902VDG — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LM2902DG | LM2902D | LM2902NSR | LM2902DG4 | LM2902KPWR | LM2902VDR2 |
|---|---|---|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | onsemi | onsemi | Texas Instruments | onsemi | onsemi | onsemi | onsemi |
| Amplifier Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Input Configuration | True differential input | True differential input | Differential input | True differential input | True differential input | True differential input | True differential input |
| Power Supply Type | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply |
| Frequency Compensation | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated |
Diferensiator Kunci
- Four independent general-purpose amplifiers in one package (vsLM2902D)
- Wide positive-supply operating range (vsLM2902DG)
- Direct LM2902-family ordering compatibility (vsLM2902KPWR)
- Documented industry-standard family lineage (vsLM2902VDR2)
Catatan Desain
Place the required bypass capacitor immediately between the positive-supply pin and ground pin of the LM2902VDG. Keep the path between pin 11 and the capacitor as short as possible, with a low-impedance ground return, because long supply loops can impair stability in high-gain or capacitive-load circuits. Route all four channels symmetrically where matching matters, and place feedback components directly beside their associated amplifier pins.
Do not design a zero-crossing comparator around a bipolar-input LM2902 without first establishing the required input common-mode voltage. In a single-supply circuit, bias the reference or signal above ground so both inputs remain within the datasheet common-mode range. Also verify output swing at the selected load. If the source can cross either supply rail or the comparator requires fast, controlled saturation, use a rail-to-rail-input amplifier or dedicated comparator instead.
Use a single solid ground reference for the analog section and connect shunt or sensor returns with a Kelvin path where accurate current sensing is required. Keep high-impedance input traces short, shield them where necessary, and avoid routing them beside switching-regulator outputs, relay traces, or high-current motor wiring. Separate feedback and compensation paths from digital return currents so switching noise does not enter the signal reference.
Verify the complete rail tolerance and transient range against the 3 V to 32 V operating specification before applying the LM2902VDG to a 24 V industrial bus. Include startup overshoot, supply ripple, inductive spikes, and regulator dropout margin. Input and output voltages must also remain inside their respective limits. Reverse-polarity, overvoltage, and short-circuit protection should be implemented outside the amplifier when the system environment can expose the device to those faults.
Informasi Konformitas
No definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statements were identified for the exact LM2902VDG ordering code. These fields require confirmation from the current onsemi product declaration or ordering documentation.