LT1498IS8 - 10MHz Dual Precision Op Amp | Analog Devices
MPN: LT1498IS8 ✓ AktifLT1498IS8 Ringkasan
An operational amplifier is an amplifier IC that uses very high open-loop gain to control an analog signal. The LT1498 belongs to the precision operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and broader semiconductor hierarchies. Its rail-to-rail input stage accepts signals near either supply rail, while the rail-to-rail output stage can swing close to the output limits under suitable load conditions.
The principal features include a 10 MHz gain-bandwidth product, a 6 V/us slew rate, dual-amplifier construction, precision C-Load capability, and rail-to-rail input and output operation. These characteristics make the LT1498IS8 suitable for sensor interfaces, audio paths, ADC and DAC drivers, active filters, and general-purpose instrumentation where a conventional single-supply amplifier cannot accommodate signals near its positive supply rail.
The 10 MHz gain-bandwidth product supports useful closed-loop bandwidth above the audio range, while the 6 V/us slew rate improves large-signal response. Precision C-Load operation reduces the likelihood of instability when driving isolated capacitive loads. However, the exact stability network and load limits must be selected using the application circuit and recommendations in the manufacturer datasheet rather than inferred from generic amplifier practice.
Typical applications include buffering sensor outputs, driving mixed-signal converters, amplifying audio signals, active filtering, and providing precision gain in test and measurement equipment. In a ±15 V instrumentation system, its dual amplifier architecture supplies two independent channels in one package, reducing board area when both channels are required.
Designers should verify input common-mode range, output swing, capacitive-load stability, noise, offset, and supply-current requirements for the operating conditions. Place input, feedback, and decoupling connections to minimize parasitic capacitance, and route output currents away from sensitive input nodes to limit crosstalk and unintended feedback.
Alternatif penggantian untuk LT1498IS8 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
LT1498IS8#PBF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LT1498IS8#TR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LT1498IS8#TRPBF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LT1498CS8#PBF
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LT1498CN8
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LT1498IS8 Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Dual precision operational amplifier |
| Number of Amplifiers | 2 channels |
| Gain-Bandwidth Product | 10 MHz |
| Slew Rate | 6 V/us |
| Input Common-Mode Range | Rail-to-rail input |
| Tipe Output | Rail-to-rail output |
| Capacitive Load Capability | Precision C-Load operation |
| Supply Voltage Range | 2.2 V to 15 V |
| Supported Supply Configuration | ±15 V / 30 V total |
| Paket | 8-pin SOIC |
| Tipe Mounting | Surface mount |
LT1498IS8 8-pin soic Diamant Konfigurasi Panduan
Konfigurasi pin untuk LT1498IS8 (8-pin soic pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk LT1498IS8.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
LT1498IS8 cocok untuk 6 aplikasis: ADC Front-End Signal Conditioning, Precision Active Filtering, Audio Signal Buffering, Sensor Signal Conditioning, DAC Output Buffering, Industrial Instrumentation.
ADC Front-End Signal Conditioning
The LT1498IS8 fits between a sensor or analog front end and a high-resolution ADC because its rail-to-rail input stage accepts signals across most of the 2.2 V to 15 V supply range. The 10 MHz gain-bandwidth product provides bandwidth for moderate-gain conditioning, while the 6 V/us slew rate supports fast input transitions. Precision C-Load operation can simplify interfacing to sampling nodes, although the converter's drive and settling requirements must still be verified. Use short feedback paths, place the amplifier near the ADC, and decouple the supply rail to minimize acquisition error and high-frequency coupling.
Direkomendasikan
Precision Active Filtering
The LT1498IS8 is appropriate for precision active filters requiring more bandwidth and slew-rate margin than a conventional micropower amplifier. Its 10 MHz gain-bandwidth product allows several closed-loop bandwidth choices around audio or low-frequency instrumentation ranges, and the 6 V/us slew rate improves behavior when the filter must process larger signals. Rail-to-rail input and output operation improves signal utilization at low supply voltages. Select resistor and capacitor values for the intended gain and bandwidth, and verify phase margin and capacitive loading using the manufacturer's application guidance before finalizing the filter response.
Direkomendasikan
Audio Signal Buffering
The LT1498IS8 can buffer dual audio channels while retaining useful small- and large-signal bandwidth. Its 10 MHz gain-bandwidth product is substantially above the audio band, and the 6 V/us slew rate provides margin for high-amplitude waveforms without requiring an oversized output stage for basic buffering. Rail-to-rail input and output operation is valuable in single-supply equipment where the signal approaches either rail. Choose the channel assignment and external gain structure carefully, maintain short output routing to downstream stages, and check the loaded output-voltage limits at the selected supply voltage.
Direkomendasikan
Sensor Signal Conditioning
The LT1498IS8 is well matched to sensor interfaces that require rail-to-rail input behavior and more precision bandwidth than a basic general-purpose op amp. The dual circuit permits conditioning of two sensors or a differential signal path, while the 10 MHz gain-bandwidth product supports moderate closed-loop gains and the 6 V/us slew rate improves transient response. Its capacitive-load behavior can also simplify connection to sampling or multiplexing stages. Confirm sensor output range, input bias-current requirements, and grounding arrangement, then place the device close to the source to minimize noise pickup and unwanted common-mode conversion.
Direkomendasikan
DAC Output Buffering
The LT1498IS8 can serve as the output buffer for a DAC when the converter requires a low-impedance drive, rail-to-rail signal range, and controlled settling. Its 10 MHz gain-bandwidth product offers substantially more loop bandwidth than the audio or instrumentation signals commonly carried by the DAC, while the 6 V/us slew rate handles larger transient edges. Precision C-Load capability is useful when the DAC includes an isolation network or capacitive output structure. Keep the buffer's feedback loop compact, verify the DAC output range against the amplifier supply, and confirm that any required output filtering does not create excessive capacitive loading.
Direkomendasikan
Industrial Instrumentation
The LT1498IS8 suits instrumentation modules that need to process bipolar or ground-referenced sensor signals while also supporting a wide supply range. Its rail-to-rail input stage improves usable input range, the dual-channel configuration can reduce board area for measurement chains, and the 10 MHz gain-bandwidth product handles faster diagnostics than a slow precision-only amplifier. The 6 V/us slew rate supports signal steps without the severe bandwidth penalty of a very low-power implementation. Use careful grounding and supply partitioning, avoid routing output and digital signals together, and validate the complete channel for the intended common-mode, noise, and calibration requirements.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LT1498IS8 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Choose LT1498IS8#PBF for a new lead-free assembly when its documented electrical ratings and ordering conditions match the design. LT1498IS8#TR or LT1498IS8#TRPBF may serve existing assembly or logistics requirements while retaining the same core ratings. Consider LT1498CS8#PBF or LT1498CN8 only after checking their temperature-grade requirements and obtaining the authoritative ordering information. No cross-brand candidate is recommended because the available cross-reference information does not establish a pin-compatible part that also preserves the 10 MHz bandwidth, 6 V/us slew rate, rail-to-rail behavior, and C-Load capability.
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LT1498IS8#PBF | LT1498IS8#TR | LT1498IS8#TRPBF | LT1498CS8#PBF | LT1498CN8 |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| Slew Rate | 6 V/us | 6 V/us | 6 V/us | 6 V/us | 6 V/us | 6 V/us |
| Supply Voltage Range | 2.2 V to 15 V | 2.2 V to 15 V | 2.2 V to 15 V | 2.2 V to 15 V | 2.2 V to 15 V | 2.2 V to 15 V |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Capacitive Load Capability | Precision C-Load operation | Precision C-Load operation | Precision C-Load operation | Precision C-Load operation | Precision C-Load operation | Precision C-Load operation |
| Supported Supply Configuration | ±15 V / 30 V total | ±15 V / 30 V total | ±15 V / 30 V total | ±15 V / 30 V total | ±15 V / 30 V total | ±15 V / 30 V total |
Diferensiator Kunci
- Higher bandwidth than a general-purpose dual rail-to-rail amplifier (vsLT1498IS8#PBF)
- Precision C-Load operation (vsLT1498IS8#TR)
- Dual rail-to-rail precision channels in an 8-pin SOIC (vsLT1498CS8#PBF)
Catatan Desain
Do not assume that every generic 8-pin dual rail-to-rail amplifier is electrically interchangeable with the LT1498IS8. A valid replacement must reproduce the 10 MHz gain-bandwidth product, 6 V/us slew rate, supply range, rail-to-rail input and output behavior, and precision C-Load capability. Check the complete pin description table, especially exposed-pad connections and dual-channel polarity, before substituting an ordering code or manufacturer.
Place the amplifier close to the source or converter it serves, and keep feedback resistors and input nodes compact. Route each channel to minimize overlap with the other channel's output path, particularly when one amplifier drives an ADC and the other handles a clock or control signal. Place supply-decoupling capacitance at the device pins and use a low-impedance ground return to reduce supply ripple, clock feedthrough, and common-mode conversion.
Treat the LT1498IS8 as a bandwidth-sensitive precision amplifier even when the intended signal occupies a much lower frequency. The 10 MHz gain-bandwidth product and 6 V/us slew rate can expose parasitic capacitance that would be unimportant in a slow amplifier. Keep feedback loops small, avoid long stubs, and confirm capacitive-load stability for the actual gain, output filter, and external load using the manufacturer application guidance.
Informasi Konformitas
The lead-free LT1498IS8#PBF ordering designation is documented, but separate RoHS, REACH, halogen-free, and conflict-minerals statements are not present in the manufacturer product excerpts. The LT1498IS8 is an industrial analog amplifier rather than an AEC-Q100-qualified automotive device.