Analog Devices

LT1498IS8 - 10MHz Dual Precision Op Amp | Analog Devices

MPN: LT1498IS8 ✓ Active
2.2 V to 15 V Vdss 8-pin SOIC Package
MOQ: 1 |

LT1498IS8 Overview

The Analog Devices LT1498IS8 is a dual precision operational amplifier with a 10 MHz gain-bandwidth product, 6 V/us slew rate, and rail-to-rail input and output stages, housed in an 8-pin SOIC package. The device operates from 2.2 V to 15 V, supports input and output voltages extending to approximately ±15 V, and is designed for accurate signal amplification with capacitive loads.

An operational amplifier is an amplifier IC that uses very high open-loop gain to control an analog signal. The LT1498 belongs to the precision operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and broader semiconductor hierarchies. Its rail-to-rail input stage accepts signals near either supply rail, while the rail-to-rail output stage can swing close to the output limits under suitable load conditions.

The principal features include a 10 MHz gain-bandwidth product, a 6 V/us slew rate, dual-amplifier construction, precision C-Load capability, and rail-to-rail input and output operation. These characteristics make the LT1498IS8 suitable for sensor interfaces, audio paths, ADC and DAC drivers, active filters, and general-purpose instrumentation where a conventional single-supply amplifier cannot accommodate signals near its positive supply rail.

The 10 MHz gain-bandwidth product supports useful closed-loop bandwidth above the audio range, while the 6 V/us slew rate improves large-signal response. Precision C-Load operation reduces the likelihood of instability when driving isolated capacitive loads. However, the exact stability network and load limits must be selected using the application circuit and recommendations in the manufacturer datasheet rather than inferred from generic amplifier practice.

Typical applications include buffering sensor outputs, driving mixed-signal converters, amplifying audio signals, active filtering, and providing precision gain in test and measurement equipment. In a ±15 V instrumentation system, its dual amplifier architecture supplies two independent channels in one package, reducing board area when both channels are required.

Designers should verify input common-mode range, output swing, capacitive-load stability, noise, offset, and supply-current requirements for the operating conditions. Place input, feedback, and decoupling connections to minimize parasitic capacitance, and route output currents away from sensitive input nodes to limit crosstalk and unintended feedback.

Drop-in alternatives for LT1498IS8 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

LT1498IS8#PBF

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz gain-bandwidth product, 6 V/us slew rate, and 2.2 V to 15 V supply range; electrical difference is 0%, with a lead-free ordering designation.

📋 Reference alternative (not in catalog)

LT1498IS8#TR

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz gain-bandwidth product, 6 V/us slew rate, and 2.2 V to 15 V supply range; core electrical difference is 0%, with a different shipping designation.

📋 Reference alternative (not in catalog)

LT1498IS8#TRPBF

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz gain-bandwidth product, 6 V/us slew rate, and 2.2 V to 15 V supply range; core electrical difference is 0%, with a tape-and-reel lead-free designation.

📋 Reference alternative (not in catalog)

LT1498CS8#PBF

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail I/O, and 2.2 V to 15 V supply range; core electrical difference is 0%, while the ordering code identifies a different grade.

📋 Reference alternative (not in catalog)

LT1498CN8

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail I/O, and 2.2 V to 15 V supply range; core electrical difference is 0%, while the ordering code identifies a different grade.

📋 Reference alternative (not in catalog)

LT1498IS8 Maximum Ratings & Electrical Characteristics

Amplifier Type Dual precision operational amplifier
Number of Amplifiers 2 channels
Gain-Bandwidth Product 10 MHz
Slew Rate 6 V/us
Input Common-Mode Range Rail-to-rail input
Output Type Rail-to-rail output
Capacitive Load Capability Precision C-Load operation
Supply Voltage Range 2.2 V to 15 V
Supported Supply Configuration ±15 V / 30 V total
Package 8-pin SOIC
Mounting Type Surface mount

LT1498IS8 8-pin soic Pin Configuration Guide

Pin configuration for LT1498IS8 (8-pin soic package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin soic package pinout diagram for LT1498IS8

No detailed pinout data available for LT1498IS8.

Refer to the datasheet for full pin configuration.

Typical Applications

LT1498IS8 is suitable for 6 applications: ADC Front-End Signal Conditioning, Precision Active Filtering, Audio Signal Buffering, Sensor Signal Conditioning, DAC Output Buffering, Industrial Instrumentation.

🔧

ADC Front-End Signal Conditioning

The LT1498IS8 fits between a sensor or analog front end and a high-resolution ADC because its rail-to-rail input stage accepts signals across most of the 2.2 V to 15 V supply range. The 10 MHz gain-bandwidth product provides bandwidth for moderate-gain conditioning, while the 6 V/us slew rate supports fast input transitions. Precision C-Load operation can simplify interfacing to sampling nodes, although the converter's drive and settling requirements must still be verified. Use short feedback paths, place the amplifier near the ADC, and decouple the supply rail to minimize acquisition error and high-frequency coupling.

🌐

Precision Active Filtering

The LT1498IS8 is appropriate for precision active filters requiring more bandwidth and slew-rate margin than a conventional micropower amplifier. Its 10 MHz gain-bandwidth product allows several closed-loop bandwidth choices around audio or low-frequency instrumentation ranges, and the 6 V/us slew rate improves behavior when the filter must process larger signals. Rail-to-rail input and output operation improves signal utilization at low supply voltages. Select resistor and capacitor values for the intended gain and bandwidth, and verify phase margin and capacitive loading using the manufacturer's application guidance before finalizing the filter response.

🎧

Audio Signal Buffering

The LT1498IS8 can buffer dual audio channels while retaining useful small- and large-signal bandwidth. Its 10 MHz gain-bandwidth product is substantially above the audio band, and the 6 V/us slew rate provides margin for high-amplitude waveforms without requiring an oversized output stage for basic buffering. Rail-to-rail input and output operation is valuable in single-supply equipment where the signal approaches either rail. Choose the channel assignment and external gain structure carefully, maintain short output routing to downstream stages, and check the loaded output-voltage limits at the selected supply voltage.

🧩

Sensor Signal Conditioning

The LT1498IS8 is well matched to sensor interfaces that require rail-to-rail input behavior and more precision bandwidth than a basic general-purpose op amp. The dual circuit permits conditioning of two sensors or a differential signal path, while the 10 MHz gain-bandwidth product supports moderate closed-loop gains and the 6 V/us slew rate improves transient response. Its capacitive-load behavior can also simplify connection to sampling or multiplexing stages. Confirm sensor output range, input bias-current requirements, and grounding arrangement, then place the device close to the source to minimize noise pickup and unwanted common-mode conversion.

📺

DAC Output Buffering

The LT1498IS8 can serve as the output buffer for a DAC when the converter requires a low-impedance drive, rail-to-rail signal range, and controlled settling. Its 10 MHz gain-bandwidth product offers substantially more loop bandwidth than the audio or instrumentation signals commonly carried by the DAC, while the 6 V/us slew rate handles larger transient edges. Precision C-Load capability is useful when the DAC includes an isolation network or capacitive output structure. Keep the buffer's feedback loop compact, verify the DAC output range against the amplifier supply, and confirm that any required output filtering does not create excessive capacitive loading.

🏭

Industrial Instrumentation

The LT1498IS8 suits instrumentation modules that need to process bipolar or ground-referenced sensor signals while also supporting a wide supply range. Its rail-to-rail input stage improves usable input range, the dual-channel configuration can reduce board area for measurement chains, and the 10 MHz gain-bandwidth product handles faster diagnostics than a slow precision-only amplifier. The 6 V/us slew rate supports signal steps without the severe bandwidth penalty of a very low-power implementation. Use careful grounding and supply partitioning, avoid routing output and digital signals together, and validate the complete channel for the intended common-mode, noise, and calibration requirements.

What is the LT1498IS8?
The LT1498IS8 is a dual precision operational amplifier with a 10 MHz gain-bandwidth product, 6 V/us slew rate, and rail-to-rail input and output stages. According to the Analog Devices LT1498/LT1499 datasheet, it is intended for precision C-Load signal conditioning and can operate from 2.2 V to 15 V in an 8-pin SOIC package.
What are the key specifications of LT1498IS8 that engineers should know?
The LT1498IS8 combines two amplifier channels, a 10 MHz gain-bandwidth product, a 6 V/us slew rate, and rail-to-rail input and output operation in an 8-pin SOIC. According to the Analog Devices LT1498/LT1499 datasheet, its supply-voltage range is 2.2 V to 15 V and it supports ±15 V operation. Precision C-Load capability is the defining feature for applications driving isolated capacitive loads.
Where can I download the LT1498IS8 datasheet PDF?
The official LT1498IS8 datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/14989fg.pdf. The document covers the dual LT1498 and quad LT1499 family, including the 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail operation, electrical characteristics, and application guidance.
Where can I find the LT1498IS8 pinout?
Use the pin-configuration table in the Analog Devices LT1498/LT1499 datasheet to identify every LT1498IS8 connection and its exposed-pad requirements. The part is an 8-pin SOIC, but the public product excerpts do not provide a complete numbered pin-name table, so use the manufacturer drawing for authoritative signal assignments and exposed-pad connections.
What is the supply-voltage range of the LT1498IS8?
The LT1498IS8 operates from 2.2 V to 15 V according to the Analog Devices LT1498/LT1499 datasheet and the published LT1498IS8 component listing. It also supports ±15 V operation when powered from split supplies, giving a 30 V total span between the negative and positive rails. Confirm signal amplitudes and output-swing requirements at the intended supply voltage.
Is the LT1498IS8 suitable for audio applications?
The LT1498IS8 is suitable for audio applications that need rail-to-rail input and output operation with more bandwidth than a basic audio amplifier. Its 10 MHz gain-bandwidth product and 6 V/us slew rate provide useful small- and large-signal response, while the dual configuration can process two channels. The dual SOIC package and precision C-Load behavior make it useful in active audio and filtering circuits.
What can replace the LT1498IS8?
The closest documented drop-in choices are the lead-free LT1498IS8#PBF and ordering-code variants in the LT1498 family that retain the 8-pin SOIC footprint and the same 10 MHz and 6 V/us core ratings. Commercial-grade LT1498 variants may also fit electrically, but their temperature-grade details must be checked before substitution. No verified cross-brand, pin-to-pin equivalent was identified.
What is the best Analog Devices equivalent for the LT1498IS8?
The LT1498IS8#PBF is the closest documented Analog Devices equivalent because it retains the dual LT1498 amplifier, 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail I/O architecture, and 8-pin SOIC footprint. Its lead-free ordering designation distinguishes it from the original LT1498IS8 marking. Verify temperature grade, exposed-pad handling, and production status before committing it to a new design.
What is the best cross-brand equivalent for the LT1498IS8?
No cross-brand drop-in replacement can be confirmed from the available manufacturer and cross-reference information. The LT1498IS8 combines a 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail input and output, and precision C-Load behavior in an 8-pin SOIC, so a candidate must satisfy all four constraints rather than merely match amplifier count and package. Request a quote for the original part or a verified pin-compatible source.
LT1498IS8 vs LT1498IS8#PBF - which is better?
The LT1498IS8#PBF is the preferred option for a new lead-free design because it retains the LT1498 family's 10 MHz gain-bandwidth product, 6 V/us slew rate, dual rail-to-rail I/O architecture, and 8-pin SOIC footprint. The principal documented difference is the ordering and lead-free designation rather than a change to the core performance figures. Existing LT1498IS8 assemblies should retain their qualified part unless a deliberate requalification is performed.
When should I choose the LT1498IS8 over a generic dual op amp?
Choose the LT1498IS8 when the design needs rail-to-rail input and output behavior, a 10 MHz gain-bandwidth product, a 6 V/us slew rate, and dependable operation with capacitive loads. It is particularly useful for sensor buffering, mixed-signal conversion, active filtering, and two-channel audio paths. A generic amplifier is preferable only when its specified common-mode range, drive capability, and stability behavior meet the same requirements.
Is the LT1498IS8 suitable for driving an ADC or DAC?
The LT1498IS8 is suitable as a mixed-signal interface amplifier because its 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail input stage, and precision C-Load capability support many converter applications. Place it directly at the converter interface, observe the converter data sheet for drive-impedance and settling requirements, and verify that the selected gain does not compromise stability.
What thermal and power considerations apply to the LT1498IS8?
The LT1498IS8 is an analog amplifier rather than a power semiconductor, so a safe-operating-area chart does not apply. Thermal design must instead consider total supply dissipation, the SOIC package, copper area, and the maximum ambient temperature. Because the published excerpts do not include current, thermal-resistance, or junction-temperature figures, use the complete manufacturer datasheet for quantitative thermal calculations.
How does the LT1498IS8 handle capacitive loads?
The LT1498IS8 is designed for precision C-Load operation, which makes it more suitable for driving isolated capacitive loads than many general-purpose amplifiers. According to the Analog Devices LT1498/LT1499 datasheet, its 10 MHz gain-bandwidth product and 6 V/us slew rate support dynamic signal behavior. Use the manufacturer stability and capacitive-load guidance because the permissible load depends on gain, frequency, and output configuration.
Where to buy the LT1498IS8 online and what is its lead time?
Use the Request a Quote form on this page to request the LT1498IS8, current availability, lead time, and order quantity. The manufacturer lists the LT1498 family in production, but the public product excerpts do not establish a guaranteed stock level or delivery interval for this exact ordering code. A formal quotation is the appropriate way to confirm schedule, condition, and traceability requirements.

Engineering reference data for LT1498IS8 — comparison, design guidance, and compliance information.

Selection Guide

Choose the LT1498IS8 when the design requires two precision amplifier channels, a 10 MHz gain-bandwidth product, 6 V/us slew rate, rail-to-rail input and output operation, and precision C-Load behavior in an 8-pin SOIC. It is particularly suitable for ADC or DAC interfaces, sensor conditioning, active filters, and audio paths that cannot tolerate the restricted input range of a conventional single-supply amplifier.

Choose LT1498IS8#PBF for a new lead-free assembly when its documented electrical ratings and ordering conditions match the design. LT1498IS8#TR or LT1498IS8#TRPBF may serve existing assembly or logistics requirements while retaining the same core ratings. Consider LT1498CS8#PBF or LT1498CN8 only after checking their temperature-grade requirements and obtaining the authoritative ordering information. No cross-brand candidate is recommended because the available cross-reference information does not establish a pin-compatible part that also preserves the 10 MHz bandwidth, 6 V/us slew rate, rail-to-rail behavior, and C-Load capability.

Comparison with Alternatives

Parameter This Product LT1498IS8#PBF LT1498IS8#TR LT1498IS8#TRPBF LT1498CS8#PBF LT1498CN8
Package 8-pin SOIC 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Amplifier Count 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Gain-Bandwidth Product 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz
Slew Rate 6 V/us 6 V/us 6 V/us 6 V/us 6 V/us 6 V/us
Supply Voltage Range 2.2 V to 15 V 2.2 V to 15 V 2.2 V to 15 V 2.2 V to 15 V 2.2 V to 15 V 2.2 V to 15 V
Input Common-Mode Range Rail-to-rail input Rail-to-rail input Rail-to-rail input Rail-to-rail input Rail-to-rail input Rail-to-rail input
Output Type Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output
Capacitive Load Capability Precision C-Load operation Precision C-Load operation Precision C-Load operation Precision C-Load operation Precision C-Load operation Precision C-Load operation
Supported Supply Configuration ±15 V / 30 V total ±15 V / 30 V total ±15 V / 30 V total ±15 V / 30 V total ±15 V / 30 V total ±15 V / 30 V total

Key Differentiators

  • Higher bandwidth than a general-purpose dual rail-to-rail amplifier (vs LT1498IS8#PBF)
  • Precision C-Load operation (vs LT1498IS8#TR)
  • Dual rail-to-rail precision channels in an 8-pin SOIC (vs LT1498CS8#PBF)

Design Notes

Do not assume that every generic 8-pin dual rail-to-rail amplifier is electrically interchangeable with the LT1498IS8. A valid replacement must reproduce the 10 MHz gain-bandwidth product, 6 V/us slew rate, supply range, rail-to-rail input and output behavior, and precision C-Load capability. Check the complete pin description table, especially exposed-pad connections and dual-channel polarity, before substituting an ordering code or manufacturer.

Place the amplifier close to the source or converter it serves, and keep feedback resistors and input nodes compact. Route each channel to minimize overlap with the other channel's output path, particularly when one amplifier drives an ADC and the other handles a clock or control signal. Place supply-decoupling capacitance at the device pins and use a low-impedance ground return to reduce supply ripple, clock feedthrough, and common-mode conversion.

Treat the LT1498IS8 as a bandwidth-sensitive precision amplifier even when the intended signal occupies a much lower frequency. The 10 MHz gain-bandwidth product and 6 V/us slew rate can expose parasitic capacitance that would be unimportant in a slow amplifier. Keep feedback loops small, avoid long stubs, and confirm capacitive-load stability for the actual gain, output filter, and external load using the manufacturer application guidance.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The lead-free LT1498IS8#PBF ordering designation is documented, but separate RoHS, REACH, halogen-free, and conflict-minerals statements are not present in the manufacturer product excerpts. The LT1498IS8 is an industrial analog amplifier rather than an AEC-Q100-qualified automotive device.

Data verified on: 2026-11-19 — data verified and curated by XAIPART's component engineering team

Related Searches

lt1498is8 pbf LT1498IS8 datasheet LT1498IS8 datasheet pdf LT1498IS8 pinout LT1498IS8 schematic LT1498IS8 equivalent LT1498IS8 replacement LT1498IS8 cross reference LT1498IS8 vs LT1498CS8 LT1498IS8 price LT1498IS8 stock Analog Devices LT1498IS8 LT1498IS8 SOIC-8 op amp LT1498IS8 ADC driver LT1498IS8 application circuit

Related Components & Terms

Analog Devices Linear Technology LT1498IS8 LT1498IS8#PBF LT1498IS8#TR LT1498IS8#TRPBF LT1498CS8#PBF LT1498CN8 LT1499 operational amplifier precision operational amplifier voltage-feedback amplifier dual amplifier analog signal-conditioning IC semiconductor gain-bandwidth product slew rate rail-to-rail input rail-to-rail output precision C-Load 8-pin SOIC SOIC family surface-mount package ADC interface sensor signal conditioning active filter audio signal buffering
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details