MAX389EPN+ - 4:1 Differential Multiplexer | Analog Devices
MPN: MAX389EPN+ ✗ Akhir HidupMAX389EPN+ Ringkasan
An analog multiplexer is an interface IC that selects one of several input paths and connects it to an output. A 4:1 configuration gives the MAX389EPN+ four input positions per internal switch, while the two-circuit designation identifies the two switching sections used by this differential implementation. This arrangement can reduce the number of separate signal paths required in instrumentation, test systems, and other analog-routing designs.
The primary verified characteristics of the MAX389EPN+ are its dual-circuit organization, 4:1 multiplexing ratio, 3 kOhm on resistance, differential operating arrangement, industrial temperature grade, and 18-pin PDIP construction. The PDIP format uses through-hole mounting and provides generous pin spacing for laboratory, industrial control, educational, and legacy equipment designs where surface-mount assembly is not required.
The MAX389 family documentation identifies these devices as high-voltage, fault-protected analog multiplexers. That positioning makes signal-path protection an important part of circuit planning because the selected switch must tolerate the voltage and fault conditions present in the intended system. Engineers should use the manufacturer datasheet for the complete absolute maximum ratings, switching characteristics, channel configuration, control logic, and truth table before finalizing a high-energy analog front end.
Typical uses include routing differential sensor signals, selecting test points in automated measurement systems, multiplexing analog channels in industrial control equipment, and connecting external instrumentation to a shared processing chain. Because the verified information identifies a differential 4:1 architecture, the part is particularly relevant to circuits that need paired signal routing rather than a single-ended selector.
PCB design should preserve the through-hole footprint of the 18-pin PDIP package and route sensitive analog traces away from switching nodes and other high-energy circuitry. Confirm the exact pin numbering, control inputs, common-mode limits, and maximum signal voltage in the manufacturer datasheet before fabrication.
This page combines the verified device identity, package and switching characteristics with drop-in comparison information and practical guidance for industrial analog-routing designs. It distinguishes confirmed specifications from parameters that must be checked directly in the MAX389EPN+ datasheet.
Alternatif penggantian untuk MAX389EPN+ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
MAX389CPN+
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
MAX389EPN+ Spesifikasi
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | 4:1 |
| On Resistance | 3 kOhm |
| Switch Type | Differential analog multiplexer |
| Number of Terminals | 18 terminals |
| Paket | 18-pin PDIP |
| Package Code | DIP |
| Package Shape | Rectangular |
| Tipe Mounting | Through hole |
| Surface Mount | No |
| Temperature Grade | Industrial |
| Protection Function | Fault-protected |
| Product Category | Analog switch and multiplexer interface IC |
| Manufacturer | Analog Devices / Maxim Integrated |
MAX389EPN+ rectangular Diamant Konfigurasi Panduan
Konfigurasi pin untuk MAX389EPN+ (rectangular pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk MAX389EPN+.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
MAX389EPN+ cocok untuk 6 aplikasis: Industrial Analog Sensor Routing, Automated Test Signal Multiplexing, Laboratory Instrumentation, Process Control Signal Conditioning, Data Acquisition Front Ends, Communication and RF Test Systems.
Industrial Analog Sensor Routing
The MAX389EPN+ fits industrial analog-routing designs that require two differential 4:1 switching sections in an 18-pin PDIP package. Its 3 kOhm on resistance and fault-protected family architecture are useful when selecting among several sensor or conditioning outputs before an amplifier, controller, or data-conversion stage. The through-hole package also suits long-life industrial control equipment that is assembled or serviced without fine-pitch surface-mount tools. Before final circuit release, verify signal-voltage limits, control levels, and channel timing in the Maxim Integrated MAX389EPN datasheet.
Direkomendasikan
Automated Test Signal Multiplexing
The MAX389EPN+ can route paired analog test channels in automated measurement and instrumentation systems where two 4:1 multiplexer sections are preferable to multiple discrete selectors. The differential configuration supports measurements that benefit from routing a signal and its reference through coordinated paths. Its 3 kOhm on resistance must be included when evaluating test accuracy, while the fault-protection feature should be checked against the voltage and source impedance of the fixture. Use the manufacturer truth table and electrical characteristics to implement control logic correctly.
Direkomendasikan
Laboratory Instrumentation
The MAX389EPN+ is suitable for laboratory instrumentation built around interchangeable analog front ends. Two 4:1 differential sections allow several conditioned inputs to share a downstream instrument channel, while the 18-pin PDIP format simplifies prototype assembly, socket use, and manual replacement in educational or service-oriented equipment. The 3 kOhm on resistance contributes to signal attenuation and should be compared with the selected amplifier's input impedance. Confirm maximum signal voltage and switching behavior against the Maxim Integrated datasheet before connecting external test leads.
Direkomendasikan
Process Control Signal Conditioning
The MAX389EPN+ can be used in process-control equipment to select among several differential analog inputs before signal conditioning or controller input stages. Its industrial temperature grade supports industrial environments, and the dual 4:1 topology reduces the number of separate analog switches required when paired signals share common downstream circuitry. Because process signals may contain transients or abnormal voltages, the circuit should include appropriate source protection and use the documented fault-protection ratings. Verify common-mode range and operating limits in the manufacturer datasheet.
Direkomendasikan
Data Acquisition Front Ends
The MAX389EPN+ is useful in data-acquisition front ends requiring analog multiplexing ahead of an amplifier, converter, or sampling system. Its differential 4:1 arrangement can route paired inputs while preserving a consistent signal structure through the board. The 3 kOhm on resistance must be considered together with switch capacitance, source impedance, and acquisition bandwidth, so timing and capacitance values should be obtained from the MAX389EPN datasheet. The 18-pin PDIP footprint is particularly convenient for instrumentation platforms intended for service and prototype use.
Direkomendasikan
Communication and RF Test Systems
The MAX389EPN+ can serve as a controlled analog routing element in communication and RF test systems when several low- or moderate-level measurement paths must reach shared test circuitry. The differential 4:1 architecture, 3 kOhm on resistance, and fault-protection positioning are useful for controlled routing, although insertion loss and high-frequency behavior remain design constraints. Use the manufacturer's switching-time and capacitance data to establish usable bandwidth. The through-hole PDIP package also makes the device practical in laboratory fixtures and legacy test platforms.
Direkomendasikan
Data referensi engineering untuk MAX389EPN+ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | MAX389CPN+ |
|---|---|---|
| Package | 18-pin PDIP | PDIP; reported as package and terminal compatible |
| Brand | Analog Devices | Analog Devices |
| Mounting Type | Through hole | Through hole |
Diferensiator Kunci
- Documented dual differential multiplexing architecture (vsMAX389CPN+)
- Verified on-resistance and industrial grade (vsMAX389CPN+)
- Supported package-compatible service replacement (vsMAX389CPN+)
Catatan Desain
Create the PCB footprint from the 18-pin PDIP dimensions in the MAX389EPN datasheet rather than adapting a 16-pin or 20-pin DIP footprint. Preserve adequate spacing around the device for through-hole soldering, inspection, and socket use. Route the selected analog paths away from digital control traces and power-switching nodes, and use a ground-reference strategy that minimizes differences between the two differential switching paths.
Include the 3 kOhm on resistance in the input-impedance calculation for every selected channel. The attenuation introduced by the switch is also affected by source impedance, downstream amplifier input impedance, and off-channel behavior. For higher-speed or high-impedance nodes, obtain the manufacturer switching-time and capacitance values before estimating usable bandwidth. Keep sensitive traces short and provide a nearby ground return to reduce coupling into the differential signal path.
Do not treat the fault-protected MAX389 family description as permission to exceed the device's absolute maximum ratings. Confirm the allowable analog signal voltage, supply range, control-input thresholds, and channel state for every operating condition in the manufacturer datasheet. Also verify the truth table before firmware or logic design; incorrect select and enable sequencing can connect unintended sources or place the instrumentation in an invalid state.
Informasi Konformitas
The identified industrial product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Confirm compliance with the manufacturer product page or declaration for the exact ordering suffix.