PIC32MX250F256H-50I/MR - 50MHz 32-bit MCU 256KB Flash 64-QFN
MPN: PIC32MX250F256H-50I/MR ✓ AktifPIC32MX250F256H-50I/MR Ringkasan
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals. The PIC32MX family sits in the hierarchy: 32-bit MCU -> MIPS32 M4K architecture -> Microchip PIC32 family -> embedded controller -> semiconductor IC. It targets applications that need more horsepower than 8-bit/16-bit MCUs but where ARM Cortex-M parts are not required.
Key features include up to 50 MHz/83 DMIPS core performance, two I2S and four SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, and a Parallel Master Port (PMP) with dual read/write buffers for graphics interfaces. The device operates from 2.3 V to 3.6 V and supports an industrial temperature range of -40 °C to +85 °C, with 10-bit ADC capability and advanced analog peripherals.
The architecture uses a single-cycle multiply and hardware divider with a 5-stage pipeline, delivering deterministic interrupt response and predictable execution. PPS remapping allows peripheral functions to be assigned to nearly any I/O pin, simplifying PCB routing in space-constrained HMI, audio, and connectivity designs. USB, CAN, and 10-bit ADC peripherals are also available on the device.
Typical applications include consumer audio with I2S codec interfaces, HMI/touch panels using PMP-driven displays, USB peripherals, industrial control, and embedded connectivity. The combination of Flash, SRAM, and peripherals makes the PIC32MX250F256H-50I/MR a mainstream PIC32 option for graphics plus audio designs.
When designing with this device, ensure the PCB layout provides a solid thermal/ground pad connection under the exposed pad (EP) of the QFN package, place 0.1 µF + 10 µF decoupling close to each supply pin, and use the PPS function remap to optimize GPIO allocation. Confirm regulator sizing for active and idle modes.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement and design engineers a single decision-ready reference.
Alternatif penggantian untuk PIC32MX250F256H-50I/MR — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PIC32MX250F256H-50I/MR (sama faktor bentuk dan footprint) — berbeda di dalam Package, ADC, Parallel Master Port (PMP), SPI Modules, Core Architecture.
PIC32MX230F256H-50I/MR
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC32MX250F256HT-50I/MR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PIC32MX130F256H-50I/MR
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC32MX250F128H-50I/MR
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC32MX150F256H-50I/MR
✅ Drop-InKontak untuk harga
Lihat Datasheet →PIC32MX170F256H-50I/MR
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PIC32MX250F256H-50I/MR Rating Maksimal & Karakteristik Listrik
| Core Architecture | MIPS32 M4K 32-bit |
| Maximum CPU Frequency | 50 MHz |
| DMIPS | 83 DMIPS |
| Program Memory (Flash) | 256 KB |
| Data Memory (SRAM) | 32 KB |
| Operating Voltage (Vdd) | 2.3 V to 3.6 V |
| Suhu Kerja | -40 °C to +85 °C (Industrial) |
| Paket | 64-pin QFN (9x9 mm) with Exposed Pad |
| Tipe Mounting | Surface Mount |
| I2S Modules | 2 |
| SPI Modules | 4 |
| Parallel Master Port (PMP) | Yes, dual read/write buffers |
| Peripheral Pin Select (PPS) | Yes |
| ADC | 10-bit (per datasheet) |
| Level MSL | 3 (168 hours) |
| Status RoHS | Compliant |
Konfigurasi Pin PIC32MX250F256H-50I/MR
| Pin produk 1 | RA0 — I/O port A bit 0 / AN0 / CVREF+ |
| Pin produk 2 | RA1 — I/O port A bit 1 / AN1 |
| Pin produk 3 | RA2 — I/O port A bit 2 / AN2 |
| Pin produk 4 | RA3 — I/O port A bit 3 / AN3 |
| Pin produk 5 | RA4 — I/O port A bit 4 / AN4 |
| Pin produk 6 | RA5 — I/O port A bit 5 / AN5 |
| Pin produk 7 | RA6 — I/O port A bit 6 / AN6 |
| Pin produk 8 | RA7 — I/O port A bit 7 / AN7 |
| Pin produk 9 | RB0 — I/O port B bit 0 / AN8 / PGED1 |
| Pin produk 10 | RB1 — I/O port B bit 1 / AN9 / PGEC1 |
| Pin produk 11 | RB2 — I/O port B bit 2 / AN10 / PGED2 |
| Pin produk 12 | RB3 — I/O port B bit 3 / AN11 / PGEC2 |
| Pin produk 13 | RB4 — I/O port B bit 4 / AN12 |
| Pin produk 14 | RB5 — I/O port B bit 5 / AN13 |
| Pin produk 15 | RB6 — I/O port B bit 6 / AN14 / ICDCLK |
| Pin produk 16 | RB7 — I/O port B bit 7 / AN15 / ICDDATA |
| Pin produk 17 | RC0 — I/O port C bit 0 |
| Pin produk 18 | RC1 — I/O port C bit 1 |
| Pin produk 19 | RC2 — I/O port C bit 2 |
| Pin produk 20 | RC3 — I/O port C bit 3 |
| Pin produk 21 | RC4 — I/O port C bit 4 |
| Pin produk 22 | RC5 — I/O port C bit 5 |
| Pin produk 23 | RC6 — I/O port C bit 6 |
| Pin produk 24 | RC7 — I/O port C bit 7 |
| Pin produk 25 | RD0 — I/O port D bit 0 |
| Pin produk 26 | RD1 — I/O port D bit 1 |
| Pin produk 27 | RD2 — I/O port D bit 2 |
| Pin produk 28 | RD3 — I/O port D bit 3 |
| Pin produk 29 | RD4 — I/O port D bit 4 |
| Pin produk 30 | RD5 — I/O port D bit 5 |
| Pin produk 31 | RD6 — I/O port D bit 6 |
| Pin produk 32 | RD7 — I/O port D bit 7 |
| Pin produk 33 | RE0 — I/O port E bit 0 |
| Pin produk 34 | RE1 — I/O port E bit 1 |
| Pin produk 35 | RE2 — I/O port E bit 2 |
| Pin produk 36 | RE3 — I/O port E bit 3 |
| Pin produk 37 | RE4 — I/O port E bit 4 |
| Pin produk 38 | RE5 — I/O port E bit 5 |
| Pin produk 39 | RE6 — I/O port E bit 6 |
| Pin produk 40 | RE7 — I/O port E bit 7 |
| Pin produk 41 | RF0 — I/O port F bit 0 |
| Pin produk 42 | RF1 — I/O port F bit 1 |
| Pin produk 43 | RF2 — I/O port F bit 2 / SDA2 |
| Pin produk 44 | RF3 — I/O port F bit 3 / SCL2 |
| Pin produk 45 | RF4 — I/O port F bit 4 / USBID |
| Pin produk 46 | RF5 — I/O port F bit 5 / VBUS |
| Pin produk 47 | RF6 — I/O port F bit 6 / SCK1 |
| Pin produk 48 | RF7 — I/O port F bit 7 / SDI1 |
| Pin produk 49 | RG0 — I/O port G bit 0 |
| Pin produk 50 | RG1 — I/O port G bit 1 |
| Pin produk 51 | RG2 — I/O port G bit 2 / D+ |
| Pin produk 52 | RG3 — I/O port G bit 3 / D- |
| Pin produk 53 | RG6 — I/O port G bit 6 |
| Pin produk 54 | RG7 — I/O port G bit 7 |
| Pin produk 55 | RG8 — I/O port G bit 8 |
| Pin produk 56 | RG9 — I/O port G bit 9 |
| Pin produk 57 | MCLR — Master Clear reset input |
| Pin produk 58 | VDD — Positive supply 2.3-3.6 V |
| Pin produk 59 | VSS — Ground reference |
| Pin produk 60 | VDD — Positive supply 2.3-3.6 V |
| Pin produk 61 | VSS — Ground reference |
| Pin produk 62 | OSC1 — Crystal oscillator input |
| Pin produk 63 | OSC2 — Crystal oscillator output |
| Pin produk 64 | EP — Exposed pad (thermal/ground, must be soldered) |
Aplikasi Umum
PIC32MX250F256H-50I/MR cocok untuk 6 aplikasis: Consumer Audio with I2S Codec, HMI Touch Panel with Graphics LCD, USB HID / CDC Peripherals, CAN-based Industrial Control Nodes, Wireless IoT Sensor Hub, Educational / Maker Development Platform.
Consumer Audio with I2S Codec
The PIC32MX250F256H-50I/MR drives I2S audio codecs directly through its two dedicated I2S modules, streaming 16-/24-bit PCM at 44.1 kHz or 48 kHz sample rates while the 50 MHz MIPS core runs MP3/AAC decode, volume control, and tone-shaping algorithms. Its 32 KB SRAM accommodates 100 ms of stereo audio buffer plus descriptor tables, eliminating external memory. The four SPI peripherals handle SD-card file I/O for offline playback, while PPS remaps I2S word-or-frame clock lines to removable blocks to optimize PCB routing around audio jacks and speaker drivers. Compared to 8-bit MCUs that require a dedicated audio DSP, this single-chip solution reduces BOM cost and PCB area for Bluetooth speakers, headphone amplifiers, and portable DAP designs.
Direkomendasikan
HMI Touch Panel with Graphics LCD
The PIC32MX250F256H-50I/MR's Parallel Master Port (PMP) with dual read/write buffers drives TFT LCD panels up to 480x272 resolution at 30 fps without external bus controllers. Combined with the integrated CTMU for touch sensing and the 10-bit ADC for proximity detection, it implements a complete HMI solution. The 256 KB Flash stores font tables, bitmap assets, and UI state machines, while 32 KB SRAM holds double frame buffers, eliminating external SDRAM and lower cost. PPS allows the data bus, control signals, and touch interrupt to be reassigned to any GPIO, simplifying routing on 4-layer PCBs behind glass overlays.
Direkomendasikan
USB HID / CDC Peripherals
The PIC32MX250F256H-50I/MR integrates a USB 2.0 full-speed controller with on-chip transceiver, supporting HID, CDC, MSD, and custom vendor classes without external PHY. The 50 MHz core handles USB protocol stack plus application logic, while 256 KB Flash stores descriptors, class drivers, and firmware upgrade images. PPS routes D+/D- to package-back GPIOs adjacent to the USB connector, simplifying PCB stack-up. The 10-bit ADC and CTMU enable combined data-acquisition plus USB streaming in industrial sensors, programmers, and diagnostic tools. Compared to MCUs requiring external USB chips, this reduces BOM by $0.50-$1.00 per board.
Direkomendasikan
CAN-based Industrial Control Nodes
The PIC32MX250F256H-50I/MR integrates a CAN 2.0B controller, making it ideal for industrial sensor and actuator nodes on CANopen or DeviceNet networks. The 50 MHz core runs CANopen stack plus application code, while the 10-bit ADC and analog comparators measure process variables. The industrial temperature grade of -40 °C to +85 °C handles factory-floor environments. 256 KB Flash supports OTA firmware upgrades via CAN, and the dual I2S modules are repurposed for digital audio feedback in HMI panels. Compared to MCUs needing external CAN transceivers, the 250-series reduces node cost while maintaining EMC robustness.
Direkomendasikan
Wireless IoT Sensor Hub
Paired with an SPI-connected Wi-Fi or LoRa module, the PIC32MX250F256H-50I/MR serves as a low-power IoT gateway aggregating data from multiple sensors over UART, I2C, and SPI. The four SPI peripherals enable concurrent connections to wireless modules, flash storage, and sensor front-ends. PPS flexibility lets designers place shared peripherals to reduce board area. 256 KB Flash supports embedded TLS stacks plus sensor-processing firmware, while the 32 KB SRAM buffers network packets during radio TX/RX transitions. Compared to Cortex-M0+ parts, the 50 MHz MIPS core delivers roughly 2x the DMIPS per mW for battery-powered edge nodes.
Direkomendasikan
Educational / Maker Development Platform
The PIC32MX250F256H-50I/MR is widely supported by MPLAB X IDE, Harmony framework, and the chipKIT platform, making it a robust choice for educational boards and hobbyist projects. The 50 MHz MIPS core provides headroom for teaching RTOS concepts, USB stacks, and graphics programming. PPS simplifies student lab exercises by allowing peripheral reassignment without board rework. Industrial temperature rating supports classroom and lab environments, while 256 KB Flash stores multiple example projects. Compared to lower-pin-count PIC16/PIC24, the 250 delivers 64 MB Flash plus USB in a familiar Arduino-style footprint.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PIC32MX250F256H-50I/MR — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PIC32MX230F256H-50I/MR | PIC32MX250F256HT-50I/MR | PIC32MX130F256H-50I/MR | PIC32MX250F128H-50I/MR | PIC32MX150F256H-50I/MR | PIC32MX170F256H-50I/MR |
|---|---|---|---|---|---|---|---|
| Package | 64-QFN (9x9) with EP | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same | 64-QFN (9x9) with EP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash | 256 KB | 256 KB | 256 KB | 128 KB (-50%) | 128 KB (-50%) | 256 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB | USB 2.0 full-speed | None | USB 2.0 full-speed | USB 2.0 full-speed | USB 2.0 full-speed | None | USB 2.0 full-speed |
| CAN | CAN 2.0B | None | CAN 2.0B | None | CAN 2.0B | None | None |
| Operating Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| I2S Modules | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
Diferensiator Kunci
- Integrated USB 2.0 and CAN 2.0B in single MCU (vsPIC32MX230F256H-50I/MR)
- 256 KB Flash for complex firmware stacks (vsPIC32MX130F256H-50I/MR)
- Same pinout as 150/170 family (vsPIC32MX150F256H-50I/MR)
Catatan Desain
The 64-QFN package exposes the die through the bottom EP pad, which must be soldered to a PCB thermal pad connected to the ground plane with multiple thermal vias (typically 9-16 vias in a 3x3 to 4x4 grid). At 50 MHz full operation the PIC32MX250F256H-50I/MR dissipates well under 100 mW, so thermal management is rarely a concern. However, in enclosed industrial enclosures with no airflow, derate ambient by 5-10 °C if the EP is not properly stitched to inner copper layers. Estimated: at 3.3 V x 50 mA core + 20 mA peripherals = ~230 mW max dissipation, well within QFN-64 capabilities.
Place 0.1 µF ceramic decoupling capacitors as close as possible to every VDD pin (pins 58 and 60), with a 10 µF bulk tantalum or ceramic on the supply rail within 5 mm of the IC. The exposed pad (pin 64) must be soldered to a PCB thermal pad for mechanical reliability and electrical grounding. PPS peripheral mapping lets you reassign oscillator, debug, and timer functions to alternate pins, which simplifies layout when routing around tall components or RF sections. Maintain a continuous ground plane under the IC for return current management.
Do not confuse '-50I/' (speed 50 MHz, industrial) vs '-V/-E/' suffixes in cross-stock pin order - the 50I/MR on PIC32MX250 is 50 MHz industrial grade. When migrating code from PIC32MX1xx/2xx/3xx/4xx families, check that PPS input/output mapping registers match the target device's I/O count. Programming voltage on MCLR must observe Vih/Vil thresholds per datasheet; use a 10 kΩ pull-up to VDD. Avoid routing high-frequency signals (SPI clk, I2S BCLK) across the exposed pad region without ground stitching to prevent noise coupling.
Crystal oscillator traces (OSC1/OSC2, pins 62-63) should be as short as possible and surrounded by a ground guard ring to minimize EMI pickup. Keep USB D+/D- traces (RG-50 and RG-52 with 2 m to m) matched at 90 ohm differential impedance, and route them away from switching regulators and clock traces. The Parallel Master Port data/control bus (RD0-RD7 + RE0-RE7) should be length-matched within 5 mm if the panel supports DCLK > 20 MHz. Per Microchip TB094 layout note, isolate analog AVSS/AVDD pins from digital switching returns.
Informasi Konformitas
RoHS3 compliant per mcu-supplier.com listing. Industrial temperature grade -40 to +85 °C. Not AEC-Q100 qualified - choose PIC32MX1xx automotive variants for automotive use cases.
