集積回路

MC9S12NE64CPV

MC9S12NE64CPV - HCS12 16-Bit MCU 64KB Flash w/ Ethernet | NXP

The NXP (formerly Freescale) MC9S12NE64CPV is a 16-bit HCS12 microcontroller IC integrating a 10/100 Mbps Ethernet MAC (EMAC) and PHY, delivering 25 MHz CPU performance, 64 KB of Flash program memory, and 8 KB of RAM, all packaged in a 112-pin LQFP (20x20 mm) for industrial-grade embedded networking. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash/ROM), data memory (RAM), and a rich set of on-chip peripherals such as timers, ADC, communication controllers, and I/O. The HCS12 family belongs to the 16-bit microcontroller hierarchy, sitting between 8-bit MCUs (8051, AVR) and 32-bit MCUs (ARM Cortex-M), and is widely used in automotive body electronics and industrial control. The 'NE' sub-family specifically adds an integrated Ethernet MAC and 10/100 PHY, eliminating the need for an external ENC28J60 or similar Ethernet controller and dramatically simplifying TCP/IP-enabled designs. Key features include 64 KB (64K x 8) Flash, 8 KB RAM, 70 user I/O pins, a 25 MHz bus clock, an on-chip Ethernet MAC+PHY, and multiple serial interfaces including SCI (UART), SPI, and I2C. The integrated 10/100 Ethernet transceiver supports both MII and RMII interfaces to an external PHY or magnetics, enabling direct RJ-45 connectivity. Two 8-channel 10-bit ADC modules, an 8-channel PWM, and a CAN 2.0 controller round out the peripheral set. The HCS12 CPU core uses a 16-bit CISC architecture with a background debug mode (BDM) for non-intrusive in-circuit programming and debugging. Its low-power HCS12 core, combined with wait and stop modes, makes the device attractive for power-conscious industrial nodes. The integrated EMAC implements full IEEE 802.3 media access control with address filtering, FIFOs, and DMA, allowing the CPU to offload packet processing. Typical applications include industrial Ethernet nodes (Modbus TCP, EtherNet/IP gateways), HVAC building automation controllers, networked sensor hubs, smart metering, and automotive Ethernet bridge prototypes. The integrated PHY and 64 KB Flash are sufficient to run lightweight TCP/IP stacks such as uIP or lwIP for embedded web servers. When designing with this MCU, ensure the LQFP-112 footprint allocates a generous copper pour for thermal dissipation (1.5 W typical Ethernet activity) and follow NXP AN128.1EB reference layout for the analog Ethernet signals to meet IEEE 802.3 EMI margins. A 25 MHz crystal or active oscillator must be tied to the EXTAL/XTAL pins with proper load capacitors. This page synthesizes distributor pricing, drop-in alternatives within the HCS12 family, and practical design notes not found in the standalone manufacturer datasheet.

見積もりお問い合わせ

MC9S12NE64CPVE

MC9S12NE64CPVE - 16-Bit HCS12 MCU, 64KB Flash, Ethernet | NXP

The NXP MC9S12NE64CPVE is a 16-bit HCS12 CISC microcontroller integrating 64KB of Flash memory, an integrated 10/100 Ethernet MAC with PHY, and a rich set of peripherals, housed in a 112-pin LQFP (20x20 mm) industrial-grade package. It operates from a 2.5V/3.3V supply, runs at up to 25 MHz bus frequency, and is built on NXP's mature HCS12 architecture used widely in industrial Ethernet-embedded designs. What is an HCS12 microcontroller? An HCS12 (also called S12) microcontroller is a 16-bit CISC MCU family originally developed by Freescale and now maintained by NXP. It belongs to the broader hierarchy of microcontroller -> embedded microcontroller -> HCS12 (S12) family. HCS12 parts pair a 16-bit data path with peripheral coprocessors (such as the EPHY for Ethernet) and a Background Debug Mode (BDM) interface, allowing in-circuit flash programming and real-time debugging without an external ICE. The MC9S12NE64CPVE specifically targets embedded networking, embedding an Ethernet MAC + PHY directly on-die so designers can add a 10/100 Mbps Ethernet port without a standalone ENC28J60 or DP83848 companion chip. Key features of the MC9S12NE64CPVE include 64KB on-chip Flash program memory, an integrated 10/100 Ethernet MAC with on-chip PHY, multiple Enhanced Capture timers, an 8-channel 10-bit ADC, two SCI (UART) ports, one SPI port, an I2C interface, and a 16-bit Pulse Width Modulation (PWM) module. The 112-LQFP industrial-temperature package (CPV suffix indicates -40C to +85C) gives sufficient I/O for parallel buses and external memory expansion. The MC9S12NE64CPVE runs the HCS12 core at 25 MHz, delivering deterministic interrupt latency and 16-bit code density well-suited for protocol stacks and industrial control loops. The integrated MAC+PHY removes the need for external PHY magnetics beyond the standard 1:1 transformer and RJ-45, simplifying BOM and PCB layout. The part supports single-wire BDM debug, watchdog, low-power Stop and Wait modes, and a real-time interrupt (RTI) block for OS scheduling. Typical applications include embedded Ethernet-enabled industrial controllers, building automation gateways, networked sensor nodes (BACnet, Modbus TCP, EtherNet/IP slave devices), and TCP/IP edge appliances. The integrated MAC+PHY makes it well suited as a low-cost web-server or serial-to-Ethernet converter, supporting uIP, lwIP, or NXP's own open-source TCP/IP stack port. Designers also use it for HVAC control boards and remote instrumentation front-ends. When designing with the MC9S12NE64CPVE, pay close attention to the integrated PHY layout: route the differential Ethernet pair (TXP, TXN, RXP, RXN) with controlled 100-ohm differential impedance, place the 49.9-ohm 1% bias resistors within 5 mm of the PHY pins, and isolate the analog AVDD pin with its own ferrite from VDDR. The on-chip voltage regulator still requires a bulk decoupling capacitor on VDDR and a small ceramic on VDD1/VDD2. This page synthesizes distributor pricing, drop-in alternatives including the MC9S12NE64CPV automotive-graded twin and other 112-LQFP NXP HCS12 family variants, and practical hardware-design notes not found in a single distributor listing.

見積もりお問い合わせ

MC9S12NE64VTU

MC9S12NE64VTU - 16-bit HCS12 MCU 64KB Flash EMAC 80-TQFP-EP | NXP

The NXP MC9S12NE64VTU is a 16-bit HCS12 CISC microcontroller integrating 64KB of on-chip Flash, an Ethernet MAC (EMAC) peripheral, and a 25 MHz CPU core, packaged in an 80-pin TQFP with an exposed thermal pad (14x14 mm). It is part of the Freescale/NXP S12NE family that combines the standard HCS12 instruction set with on-chip 10/100 Ethernet MAC support, eliminating the need for an external network controller in space-constrained designs. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash, RAM, EEPROM), and peripheral interfaces. The HCS12 family is a 16-bit CISC architecture widely used in automotive body, industrial control, and embedded networking applications because it offers deterministic interrupt behavior, a rich peripheral set, and broad toolchain support. The S12NE sub-family extends the base HCS12 with an integrated Ethernet MAC and PHY interface, making it a one-chip solution for industrial Ethernet nodes. Key features of the MC9S12NE64VTU include a 25 MHz HCS12 core delivering 25 MIPS, 64KB Flash program memory with security features, 8KB RAM, an integrated 10/100 Ethernet MAC with MII interface for an external PHY, an 8-channel 10-bit ADC, multiple timers (ECT, PWM, TIM), SCI/SPI/I2C serial interfaces, and an operating voltage of 2.5 V core / 3.3 V I/O. The on-chip EMAC supports full-duplex operation and is designed to pair with a 100BASE-TX PHY such as the MC33660 or equivalent. The 80-TQFP-EP exposed-pad package enables improved thermal dissipation for continuous Ethernet operation. The architecture is built on the proven HCS12 CPU with background debug mode (BDM), a memory protection unit option, and a flexible interrupt controller. The integrated Ethernet MAC offloads packet framing, CRC generation, and address filtering from the CPU, leaving sufficient cycles for application-layer processing at 10 Mbps and even modest 100 Mbps throughput. Operating temperature range is industrial grade, suitable for factory-floor equipment. Typical applications include industrial Ethernet gateways, building automation controllers, BACnet/IP or Modbus TCP nodes, automotive body controllers with network connectivity, and remote sensor aggregation nodes. The wide HCS12 ecosystem means abundant CodeWarrior, GCC, and third-party IDE support. Design consideration: pair the on-chip EMAC with a qualified 100BASE-TX PHY and ensure the MII traces are length-matched within 50 mils. The exposed pad must be soldered to a sufficient copper pour (>=1 sq inch) to keep junction temperature within spec during sustained MII traffic. Place a 0.1 uF decoupling capacitor within 5 mm of every VDD pin. This page synthesizes distributor pricing, drop-in alternative cross-references, and design notes that supplement the manufacturer datasheet, giving engineers a single source for selection and sourcing decisions on the MC9S12NE64VTU.

見積もりお問い合わせ

MC9S12NE64VTUE

MC9S12NE64VTUE - 16-bit HCS12 MCU, 64KB Flash, Ethernet | NXP

The NXP MC9S12NE64VTUE is a 16-bit HCS12 CISC microcontroller with integrated 10/100 Ethernet MAC (EMAC) and PHY, 64KB of Flash, an industrial temperature grade, and an 80-pin TQFP-EP (14x14 mm) package with exposed thermal pad. It operates from a 2.5V/3.3V supply at up to 25 MHz core clock and is qualified for industrial (V) temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and peripherals onto one silicon die. The HCS12 is the 16-bit successor of Freescale's HC11 architecture, and the S12 family occupies the mid-tier between 8-bit MCUs (8-bit -> 16-bit -> 32-bit microcontroller hierarchy) and high-end 32-bit ARM Cortex-M parts. The 'NE' sub-family specifically adds an on-chip 10/100 Mbps Ethernet MAC + PHY, eliminating the need for an external network interface chip in connected-embedded designs. Key features of the MC9S12NE64VTUE include: 64 KB program Flash, 8 KB SRAM, hardware IEEE 802.3 Ethernet MAC with 10/100 PHY on-chip, dual CAN 2.0 controllers (msCAN), three SCI (UART) channels, one SPI, one I2C, an 8-channel 10-bit ADC, a 16-bit timer with 8 PWM channels, and a background debug module (BDM) for in-circuit programming and debug. The 80-pin TQFP-EP package is small enough for compact embedded boards while exposing ample GPIO and bus lines for industrial connectivity. The architecture is built on the standard HCS12 CPU core with a 16-bit data path, indexed addressing, and a memory-mapped register model. The integrated Ethernet subsystem follows the IEEE 802.3 specification, with the MAC performing CSMA/CD framing and the embedded PHY handling line-side analog signaling (MLT-3 on the twisted pair, auto-negotiation, link integrity). The 25 MHz system clock is derived from an internal Phase-Locked Loop (IPLL) from an external crystal. Background Debug Mode (BDM) allows flash programming and real-time debug over a single-wire interface. Typical applications include industrial Ethernet gateways, building-automation controllers (BACnet/IP, Modbus-TCP), sensor-to-cloud bridges, embedded web servers for SCADA integration, and automotive telematics prototyping where CAN-to-Ethernet routing is needed. Designers should note that VDD/VDDX decoupling must be placed within 5 mm of each supply pin, and the 25 MHz crystal loop requires short, symmetrical traces. The on-chip EMAC + PHY removes the BOM cost of an external network controller but adds approximately 50 mA of additional supply current during active link transmission. This page synthesizes distributor pricing from DigiKey, Mouser and Octopart, plus drop-in alternative candidates from NXP's same S12NE family, along with practical design notes that the manufacturer's datasheet does not directly call out.

見積もりお問い合わせ

MC9S12P128MQK

MC9S12P128MQK - 16-Bit 128KB Flash S12 MCU | NXP | QFP-80

The NXP MC9S12P128MQK is a 16-bit HCS12-family microcontroller with 128 KB of on-chip Flash, a 32 MHz CPU12 core, and 64 general-purpose I/Os housed in an 80-pin LQFP (QFP-80, 14x14 mm) package. It is qualified to the automotive temperature grade of -40 °C to +125 °C and operates from a single 3.15 V to 5.5 V supply, targeting cost-sensitive automotive body and chassis applications. The HCS12 platform is an enhanced 16-bit CISC architecture that evolved from the original Motorola HC11 and HC12 cores. A microcontroller (MCU) is a self-contained processor with integrated Flash, RAM, peripherals, and interrupt controller on a single die; the S12 sub-family sits between 8-bit MCUs (used for simple I/O control) and 32-bit ARM Cortex-M devices (used for high-performance applications), making it well-suited for LIN nodes, body controllers, and small gateway ECUs. Key features of the MC9S12P128MQK include 6 KB of RAM, a 12-bit ADC, a 32 MHz bus clock, 64 I/O lines, and an integrated CAN and SCI/SPI peripheral set. The 80-pin LQFP package provides sufficient pin count for parallel motor driving, switch scanning, and sensor interfaces while keeping the board footprint compact for body-electronics modules. An internal phase-locked loop (IPLL) multiplies the external reference to 32 MHz, eliminating the need for an external high-frequency crystal in most designs. Architecturally, the device is built on a 0.18 µm Flash process with embedded EEPROM emulation and a background-debug mode (BDM) interface for non-intrusive in-circuit programming. The CPU12 instruction set is largely source-compatible with HC11 assembly, easing code migration. A multi-channel 16-bit timer (TIM), 8-channel 10-bit PWM, and a CAN 2.0A/B controller give the MCU enough peripheral bandwidth to drive a small body controller without an external companion chip. Typical applications include automotive body controllers, HVAC flap and blower drivers, instrument cluster sub-MCUs, lighting/ECM modules, LIN/J2602 slaves, and CAN nodes that require moderate compute and a wide temperature range. The wide supply range also allows the part to be powered directly from 12 V-derived 5 V rails in automotive systems. When designing with the MC9S12P128MQK, ensure the BDM header is brought out for production programming and that the PLL filter network follows the reference manual layout. Use at least four layers or a solid ground pour to keep digital switching noise out of the analog ADC inputs. This page synthesizes distributor stock, AEC-Q100 grade details, drop-in S12P-family alternatives, and practical PCB design notes that the standalone datasheet does not provide in a single place.

見積もりお問い合わせ

MC9S12P64CLH

MC9S12P64CLH - 16-bit 64KB Flash 32MHz CAN MCU | NXP Semiconductors

The NXP Semiconductors MC9S12P64CLH is a 16-bit HCS12 (S12 core) CAN microcontroller with 64KB of Flash program memory, a 32MHz bus, and a wide 3.13V to 5.5V supply range, housed in a 64-pin LQFP (10x10 mm) surface-mount package rated from -40C to +85C. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals on one die, forming the lowest layer of the embedded-processing hierarchy (MCU -> embedded processor -> microprocessor -> semiconductor IC). The S12P family belongs to NXP's HCS12 portfolio, a CISC-architecture 16-bit family descended from the classic 68HC12, valued in automotive body electronics for its 5V-tolerant I/O and robust EMC behavior. Key features of the MC9S12P64CLH include 64KB (64K x 8) of on-chip Flash for program storage, a single-wire background debug mode for low-cost emulation, an on-chip CAN controller for in-vehicle networking, and a supply range that tolerates automotive battery conditions without external regulation in some topologies. The device targets body control applications where 8-bit cost structures are expected but 16-bit performance is required. Technically, the S12 core executes the HCS12 instruction set with CISC efficiency, and the 32MHz bus clock is derived from an on-chip PLL/oscillator system, allowing designers to trade bus speed against EMI. Flash programming is performed in-circuit via BDM or the CAN/SCI interfaces, supporting end-of-line reprogramming in production. Typical applications include automotive body control modules, door modules, seat control, lighting control, and other CAN-networked nodes in industrial and vehicle environments. The wide temperature grade and 5V-class I/O directly suit harsh electrical environments. A key design consideration: the S12P family Flash requires proper voltage monitoring during write operations, so always enable the low-voltage inhibit and verify the bus clock is within Flash-programming limits before issuing erase/program commands. This page synthesizes distributor listings, lifecycle data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

MC9S12P64VLH

MC9S12P64VLH - 32MHz 16-Bit MCU with 64KB Flash | NXP

The NXP Semiconductors MC9S12P64VLH is a 16-bit HCS12 microcontroller with a 32 MHz S12 core, 64 KB of embedded Flash memory, and a 64-pin LQFP package. It operates across a 3.13 V to 5.5 V supply range and supports an industrial temperature grade of -40°C to +105°C. These characteristics place it in the automotive-oriented embedded control segment for body, vehicle, and industrial systems requiring CAN-capable 16-bit processing. An HCS12 microcontroller is a 16-bit CISC controller within the broader embedded microcontroller hierarchy. The S12 family combines an automotive-oriented architecture with integrated communication and timing peripherals, allowing control logic, serial communication, and signal processing to share one device. The MC9S12P64VLH provides 34 I/O ports according to its published specifications, making it suitable for systems that require more interface density than a small 8-bit or compact 16-bit controller. The device's 32 MHz operating frequency supports faster control-loop execution and more responsive communication handling than lower-frequency HCS12 devices. Its 64 KB Flash store provides 64K x 8 bits of nonvolatile program memory for firmware, while its 5 V operating point and extended temperature range suit harsh embedded environments. The package is a 64-pin gull-wing LQFP, providing a conventional surface-mount footprint with exposed perimeter pads for PCB assembly. The S12 core is a 16-bit HCS12 CISC design with integrated automotive functionality. Its architecture is intended for body and vehicle control applications where deterministic peripheral access, communication support, and a broad operating-temperature range are important. MC9S12P64VLH also appears in automotive descriptions as part of the S12P family, whose communication-oriented feature set is intended to reduce the external component count required by body-control systems. Typical uses include CAN-connected body-control modules, automotive gateway controllers, motor and solenoid management units, climate-control interfaces, sensor aggregation nodes, and industrial controllers operating from 5 V rails. Its 34 I/O ports can support discrete inputs, outputs, and communication or control signals where the exact peripheral allocation permits. Engineers should map each signal against the NXP pin-description table before finalizing the board layout. When designing around the MC9S12P64VLH, check the device's detailed electrical limits, peripheral multiplexing, oscillator options, and programming configuration in the manufacturer documentation. The 64-pin LQFP footprint requires adequate solder mask and land-pattern fidelity, while a 5 V automotive-style environment calls for careful decoupling, grounding, protection, and electromagnetic-compatibility planning around external connectors. This product record combines the manufacturer product overview, distributor identification, packaging information, and cross-reference research with practical selection guidance. It is intended to help engineers determine whether the MC9S12P64VLH fits an existing 64-pin HCS12 design and what must be verified before committing to a replacement or sourcing decision.

見積もりお問い合わせ

MC9S12P64VQK

MC9S12P64VQK - 16-bit S12 MCU 64KB Flash 32MHz QFP-80 | NXP

The NXP MC9S12P64VQK is a 16-bit HCS12 microcontroller built around the S12 CPU core, integrating 64KB of on-chip Flash, 4KB of RAM, and an MSCAN (CAN 2.0 A/B) controller in a 80-pin QFP (14x14) package. The device operates from a single 3.13V to 5.5V supply and supports a 32MHz internal bus clock, delivering roughly 25 MIPS of computational throughput across the S12P family. A 16-bit MCU is a microcontroller whose central processing unit manipulates data in 16-bit-wide words/registers rather than 8-bit bytes. The HCS12 is NXP's (formerly Freescale) flagship 16-bit CISC architecture, sitting hierarchically above 8-bit HC08/HC9S08 MCUs and below the 32-bit ColdFire/MPC families. Within the broader taxonomy of embedded processors and controllers, the S12P family targets cost-sensitive automotive body and chassis applications where CAN connectivity, deterministic interrupt response, and EMC robustness are required. Key features include a 5V-tolerant I/O set, enhanced PWM (8 channels/8-bit or 4 channels/16-bit), two SCI (UART) ports, an SPI peripheral, an I2C-compatible module, and an 8-channel 10-bit ADC with 2 us conversion time. The on-chip CAN module meets ISO 11898-1 (CAN 2.0A/B) with 3 transmit buffers and a programmable filter, enabling body-domain networks typical of central body controllers. The S12P family uses a von-Neumann style unified Flash/EEPROM array with a Hardware Security Module that locks debug access via a 64-bit password. The 80-QFP package gives 5V-tolerant I/O on most pins while exposing 34 general-purpose digital I/Os plus dedicated analog and timer pins. Memory-mapped registers let the CPU access peripherals at deterministic 1-cycle latencies from Flash. Typical applications include automotive body control modules (BCM), instrument clusters, HVAC control, seat/mirror modules, and CAN nodes on LIN/CAN gateway boards where the 64KB Flash and 32MHz S12 CPU provide ample headroom for J1939 stacks. The wide 3.13-5.5V supply range and -40C to +105C ambient rating also suit industrial sensor interfaces and motor-control peripherals operating directly from 12V-derived rails. When designing with this device, budget 1uF+0.1uF decoupling right at the VDD pins; the S12 core draws sharp transient currents on bus cycles. Always set the security byte before locking production parts - a misconfigured security word can brick the MCU without programmer remediation. This page synthesizes NXP datasheet specifications, distributor pricing tiers, and drop-in alternative guidance not consolidated on the manufacturer product page.

見積もりお問い合わせ

MC9S12P96MFT

MC9S12P96MFT - 16-bit S12 MCU, 96KB Flash, 32MHz, CAN | NXP

The NXP MC9S12P96MFT is a 16-bit HCS12 microcontroller (MCU) featuring a 32 MHz bus clock, 96 KB of embedded Flash, 4 KB EEPROM and 6 KB RAM, housed in a 48-pin QFN-EP (7x7 mm) package rated for the automotive -40C to +125C operating range. Part of NXP's S12P family, the device pairs the classic S12 CPU12 core with on-chip CAN, SCI, SPI peripherals and a PWM/LVD/POR/WDT timer block targeted at body-electronics applications. An automotive microcontroller is a small computer-on-a-chip built to drive sensors and actuators inside a car; within that hierarchy the MC9S12P96MFT belongs to the 16-bit MCU tier, the HCS12 CISC family, the S12P sub-family, and ultimately the broader power-management and body-electronics category of automotive semiconductors. Its 96 KB Flash makes it well suited to layered CAN stacks with OSEK/OS-aware boot logic, while the 32 MHz core keeps interrupt latency and CAN bit-quantum budgets predictable at 500 kbps. Key features include the 32 MHz CPU12 core with background-debug mode (BDM), 96 KB on-chip Flash (96K x 8), 4 KB EEPROM (4K x 8) for non-volatile data, 6 KB RAM (6K x 8), 34 general-purpose I/O pins, and an integrated CAN 2.0 A/B controller. The chip operates from a single 3.13 V to 5.5 V supply and includes low-voltage detect (LVD), power-on reset (POR), a watchdog timer, and PWM channels for motor and lighting control. Typical applications include automotive body control modules (BCM), HVAC control heads, instrument-cluster slaves, door/window/liftgate modules, and LIN/CAN gateway nodes where a small CAN-capable 16-bit MCU with automotive temperature range is required. The wide supply range also makes it practical for industrial 24V-bus sensor conditioning when paired with external regulators. When designing with this device, ensure the QFN-EP thermal pad is soldered to a sufficiently large copper pour to keep junction temperature within the 125C ambient rating. The CAN transceiver must be a 5 V tolerant part such as the TJA1051 or MC33901 to match the 5 V nominal supply of this MCU family. This page synthesizes distributor pricing, pin-compatible S12P alternatives, and practical design notes that are not always visible in the manufacturer datasheet. Engineers evaluating the MC9S12P96MFT for body-electronics or industrial CAN nodes should treat it as the highest-density member of the S12P 48-QFN footprint family.

見積もりお問い合わせ

MC9S12T64MPKE16

MC9S12T64MPKE16 - HCS12 16-Bit 16MHz 64KB Flash MCU | NXP

The NXP (formerly Freescale) MC9S12T64MPKE16 is a 16-bit HCS12-family microcontroller IC featuring a 16 MHz CPU, 64 KB of Flash program memory, 2 KB of EEPROM, and 4 KB of RAM in an 80-pin LQFP package measuring 12x12 mm. It provides 59 general-purpose I/O pins and integrates EBI/EMI, SCI, and SPI communication peripherals along with on-chip LVD, POR, PWM, and WDT functions for embedded control. What is an HCS12 microcontroller? The HCS12 (also called 9S12) is NXP's 16-bit automotive-grade microcontroller family, descended from the original Motorola HC11/HCS12 architecture. It sits in the broader microcontroller taxonomy as: MCU -> 16-bit MCU -> HCS12 family -> automotive MCU -> embedded processor. HCS12 devices pair a CPU12 core with enhanced peripherals, large on-chip memory, and CAN-friendly features (notably in this 'T' series targeted at body and chassis applications). Key features include the 16 MHz bus speed, 64 KB Flash organized as 64K x 8, 2 KB byte-erasable EEPROM for non-volatile parameter storage, and a 12-bit-or-better peripheral set. The chip supports 5V-tolerant I/O and integrates low-voltage detection (LVD) and power-on reset (POR) for robust automotive cold-crank behavior. The wide operating voltage range and industrial-grade temperature capability suit 12V battery-powered systems. Architecturally the device uses the CPU12 core with a 16-bit data path, BGND debug mode, and a multi-source interrupt controller. Internally, a phase-locked loop (PLL) generates the 16 MHz bus clock from an external reference. The peripheral set includes timer/PWM channels that simplify motor and solenoid drive firmware. Typical applications include automotive body controllers, instrument clusters, HVAC panels, seat-control modules, and industrial sensor interfaces that need 5V-tolerant I/O and legacy code compatibility with the HC11 family. The 'T' family specifically targets body-electronics applications. When designing with this part, plan for an external 4 MHz–16 MHz crystal or resonator because the internal PLL multiplies the reference clock. The 80-pin LQFP package has a generous thermal pad that should be soldered to the ground plane for best electrical and thermal performance. This page synthesizes distributor pricing, lifecycle status, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware teams make faster sourcing decisions.

見積もりお問い合わせ

MC9S12UF32PB

MC9S12UF32PB - HCS12 16-Bit MCU, 32KB Flash, 30MHz | NXP

The NXP MC9S12UF32PB is a 16-bit HCS12 microcontroller built around the S12 CPU core, integrating 32KB of on-chip program FLASH and 3.5KB of RAM in a 64-pin LQFP (10x10 mm) package. It runs at a 30 MHz bus speed and supports the standard HCS12 instruction set, making it suitable for legacy automotive body, chassis, and industrial control applications. The device belongs to the HCS12 family, originally introduced by Freescale Semiconductor and now supported by NXP Semiconductors following the 2015 acquisition. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (FLASH), working memory (RAM), and a rich set of peripheral blocks - timers, ADC, communication ports, and I/O - into one silicon die. MCUs sit below microprocessors in the computing hierarchy because they are self-contained, embedded, and typically run a single firmware image rather than a general-purpose operating system. The HCS12 specifically targets cost-sensitive, deterministic, real-time control tasks such as motor commutation, sensor fusion, and body-electronics modules. Key features of the MC9S12UF32PB include 41 user I/O pins, an internal oscillator that eliminates external crystal cost, and the established HCS12 peripheral set (including PWM, SCI/SPI, and timer modules per family documentation). It operates across the standard commercial temperature range, comes in a tray packaging format, and is supported by NXP's CodeWarrior and the open-source GCC toolchain. FLASH program memory is in-system programmable via the standard HCS12 BDM interface, enabling rapid prototype iteration and field firmware updates. Architecturally, the S12 core provides a 16-bit register file, 20-bit address space, and an interrupt controller optimized for fast deterministic response. Memory protection and on-chip debug enhance reliability, while the 32KB FLASH is segmented to support a small bootloader alongside application code. Compared with newer Cortex-M0+ MCUs, the HCS12 retains backward-compatibility for designs originally deployed across two decades, which is the primary reason it remains in long-life production. Typical applications include automotive body controllers, instrument cluster slaves, HVAC damper actuators, industrial sensor front-ends, and consumer appliance control boards. The wide temperature tolerance and proven HCS12 firmware ecosystem also make it suitable for retrofit designs migrating from older HC11/HCS12 derivatives. When designing with this device, ensure the BDM (background debug mode) pins are accessible for in-circuit programming and that the internal oscillator accuracy is sufficient for any UART-bound communications. For designs needing more memory, the UF32 part can typically be replaced by UF64 / UF128 variants sharing the same 64-LQFP footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a one-stop procurement and engineering reference.

見積もりお問い合わせ

MC9S12UF32PU

MC9S12UF32PU - 16-bit HCS12 MCU 32KB Flash USB 2.0 | NXP

The NXP MC9S12UF32PU is a 16-bit HCS12 microcontroller unit (MCU) built around an integrated USB 2.0 device controller, designed for memory card reader and ATA/ATAPI interface applications. The device integrates 32 KB of on-chip Flash memory (32K x 8), operates at a CPU clock of 30 MHz, and is housed in a 100-pin LQFP (14x14) package. According to DigiKey product listing data, this part is currently offered in active distribution and ships same-day from NXP USA Inc. inventory. Background: A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (typically Flash), data memory (RAM), and a rich set of peripherals such as timers, ADC, communication interfaces (UART, SPI, I2C), and increasingly specialized blocks like USB controllers. The HCS12 is NXP's (formerly Freescale's) 16-bit CISC MCU family, descended from the Motorola HC11/HC12 architecture, designed for automotive and embedded control. Microcontrollers like the MC9S12UF32PU sit within the broader hierarchy of embedded processors -> microcontrollers -> 16-bit microcontrollers -> HCS12 family, and are widely used in place of larger 32-bit ARM Cortex-M parts when cost, simplicity, and deterministic 16-bit performance matter more than raw compute. Key features of the MC9S12UF32PU include integrated USB 2.0 full-speed device functionality, dedicated ATA/ATAPI host interface logic for connecting hard drives and optical storage, and 32 KB Flash for program storage. The 100-pin LQFP (14x14 mm) package gives the part generous I/O for storage peripherals, an MSC class-compliant mass-storage interface, and ample ground and supply pins for the mixed-signal USB PHY rails. The 30 MHz bus clock is generated from an internal PLL driven by an external resonator, while Flash-resident firmware handles the USB stack and ATA command set in firmware. Technically, the S12 core is a 16-bit accumulator-based CISC design with 20-bit ALU operations and a von Neumann bus architecture. The USB 2.0 device block is on-die and exposes the standard full-speed endpoint set, so designers do not need an external USB transceiver. The integrated ATA/ATAPI host block supports PIO modes commonly used by 2.5-inch hard drives and CD/DVD optical drives, making this MCU a one-chip solution for USB mass-storage enclosures, card readers, and external optical drives. Typical applications include USB memory card readers, USB-to-ATA bridge adapters for external HDD enclosures, USB-to-ATAPI optical drive controllers, digital photo frames, and industrial data-loggers with removable storage. When designing with the MC9S12UF32PU, follow the application note guidance for USB 2.0 PHY PCB layout - keep the D+/D- traces length-matched, as short as possible, and routed over a continuous ground plane. Use the manufacturer's recommended 22 ohm series termination and a common-mode choke on the USB DP/DN lines to pass USB compliance. This page synthesizes distributor pricing, drop-in alternatives from the same NXP S12 family, and practical design notes not found in the bare manufacturer datasheet.

見積もりお問い合わせ

MC9S12UF32PUE

MC9S12UF32PUE - 16-bit USB2.0 MCU, 30MHz, 32KB Flash | NXP

The NXP MC9S12UF32PUE is a 16-bit HCS12 family microcontroller unit (MCU) with an integrated USB 2.0 full-speed device controller and ATA-5/CompactFlash/Secure Digital host interfaces, housed in a 100-pin LQFP (14x14) package. It operates at up to 30 MHz, integrates 32 KB of Flash EEPROM and 3.5 KB of RAM, and is specified for a 5V supply. The part is designed for USB mass-storage applications such as memory card readers, ATA/ATAPI bridges, and external storage devices. A microcontroller (MCU) is a single-chip computer that contains a CPU core, program memory, working RAM, and a set of on-chip peripherals. The HCS12 is a 16-bit CISC core that evolved from the original Motorola/Freescale HC11 architecture and is widely used in automotive body and chassis electronics as well as in industrial control. Microcontrollers such as the MC9S12UF32PUE sit at the lowest layer of embedded design hierarchy: MCU -> embedded processor -> semiconductor IC -> electronic component. Key features of the MC9S12UF32PUE include the integrated USB 2.0 device controller, native ATA-5 (ATAPI-6) interface for parallel hard drives, CompactFlash host controller, Secure Digital (SD) host controller, 32 KB of in-application-programmable Flash, 3.5 KB of RAM, an HCS12 16-bit CPU with up to 30 MHz bus, and a commercial temperature grade (0C to +70C per the PUE suffix). The 100-pin LQFP package exposes all peripheral buses and timers for external connections. The internal architecture pairs the HCS12 core with a unified peripheral bus, dedicated DMA for USB and ATA transfers, and dual timer modules (ECT and TIM/PWM), enabling high-throughput streaming between the USB device port and the storage media without CPU intervention. Typical applications include USB memory card readers, USB-to-ATA hard drive bridges, USB-to-CFIT / SD card readers, portable external storage enclosures, and consumer USB-storage appliances where a single-chip bridge simplifies the BOM. When designing with this part, allocate separate ground returns for the USB analog block and the digital logic, follow NXP application note layout recommendations, and verify the host-mode firmware supports the chosen card standard before committing to volume production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement engineers a single source for selection and qualification.

見積もりお問い合わせ

MC9S12XA256CAA

MC9S12XA256CAA - 16-bit HCS12X MCU, 256KB Flash, 80MHz | NXP

The NXP MC9S12XA256CAA is a 16-bit HCS12X-family microcontroller (MCU) operating at 80 MHz, integrating 256 KB of Flash program memory, in a 80-pin QFP (14x14 mm) package. The S12XA sub-family retains the cost-effective power profile, electromagnetic compatibility, and code-size efficiency of the original HCS12 line while adding an enhanced XGATE co-processor for offloading interrupt-driven tasks at up to 80 MHz. An HCS12X microcontroller is a 16-bit CISC MCU designed for automotive and industrial real-time control. HCS12X extends the original HCS12 with an XGATE peripheral co-processor, an enhanced 80 MHz bus, and richer peripheral integration. Within NXP's portfolio hierarchy, the MC9S12XA256CAA sits in the S12X → S12XA → XA256 sub-line, which is part of the broader 16-bit MCU → automotive microcontroller → embedded MCU family. Designers choose this category for deterministic interrupt latency, CAN/LIN/SPI connectivity, and EMC robustness demanded by body and chassis ECUs. Key features include 256 KB (256K x 8) Flash program memory, 16 KB RAM, 4 KB EEPROM, 8 channels of 10-bit ADC, an enhanced XGATE co-processor, and 59 general-purpose I/O lines. Peripherals include LVD, POR, PWM, WDT, SCI, SPI, I2C, IrDA, and LINbus. Connectivity covers EBI/EMI plus those serial channels, supporting both body-controller networking and sensor-actuator front-ends. The 80 MHz bus (40 MHz core / 80 MHz XGATE) doubles throughput vs. legacy HCS12. Architecturally, the MC9S12XA256CAA pairs a CISC HCS12X core with an XGATE RISC-like co-processor that handles virtual DMA-style peripheral servicing, freeing the main CPU for application code. The 2.5 V/5 V supply, on-chip EEPROM, and integrated PWM make it a strong fit for motor-control and body-electronics modules. Typical applications include automotive body controllers, instrument clusters, HVAC control modules, industrial PLC I/O expansion, and CAN/LIN gateway nodes. Automotive grade suitability is reflected in the 80-pin QFP's automotive temperature support. When designing with this MCU, ensure decoupling with 100 nF ceramics near each VDD pin and follow NXP's reference layout for the QFP-80 thermal pad. Consider XGATE firmware partitioning to maximize bus offload and reduce main-core interrupt load.

見積もりお問い合わせ

MC9S12XA256CAAR

MC9S12XA256CAAR - 16-bit 256KB Flash MCU 80MHz | NXP

The NXP Semiconductors MC9S12XA256CAAR is a 16-bit HCS12X family microcontroller with 256 KB of embedded Flash, 16 KB of RAM, 4 KB of EEPROM, and an enhanced XGATE co-processor, operating at up to 80 MHz bus speed, housed in an 80-pin LQFP (14x14 mm) package. It provides 59 general-purpose I/O pins and integrates rich connectivity including CAN, I2C, IrDA, LINbus, SCI, and SPI peripherals. An MCU (microcontroller unit) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and on-chip peripherals such as ADCs, timers, and communication interfaces. The HCS12X is a 16-bit CISC architecture MCU family used widely in automotive body, chassis, and industrial control. Within the broader taxonomy, MC9S12XA256CAAR belongs to: microcontroller -> 16-bit MCU -> HCS12X family -> automotive/industrial MCU -> embedded system. Key features of this part include 80 MHz maximum CPU frequency, 8-channel 10-bit ADC, multiple PWM channels for motor and power control, low-voltage detection (LVD), power-on reset (POR), and a window watchdog timer (WDT). The integrated XGATE co-processor offloads interrupt-driven tasks from the main CPU, boosting real-time throughput for CAN/LIN message handling and I/O processing. Operating voltage is 2.5 V core supply. Technical depth: the HCS12X core uses a 16-bit CISC instruction set with enhanced indexing and page-switching for >64 KB code spaces. The XGATE is an independent RISC-style peripheral co-processor that runs while the main core is halted, enabling deterministic interrupt latencies in the low microsecond range. The 80-QFP (14x14 mm) LQFP package provides ample PCB routing area and supports hand-soldering and rework, preferred for low-to-medium volume automotive ECUs. Typical applications include automotive body controllers, CAN/LIN gateway nodes, industrial PLC I/O modules, HVAC control boards, sensor fusion front-ends, and small motor-control BLDC drivers. The combination of 256 KB Flash and the XGATE co-processor makes it a workhorse for chassis and body domain ECUs that require deterministic communication. When designing with this part, observe the 2.5 V core supply requirement and provide adequate decoupling (>=10 uF bulk + 100 nF per VDD pin pair). The XGATE firmware must be linked into the Flash image; designers should consult the S12XD/XB/XA reference manual for the memory map and interrupt vector table before porting code. This page synthesizes distributor pricing, lifecycle status, drop-in compatible alternatives from the HCS12X family, and practical engineering notes that are not gathered in one place on the manufacturer datasheet.

見積もりお問い合わせ

MC9S12XA256CAG

MC9S12XA256CAG - 16-Bit 256KB Flash HCS12X MCU | NXP

The NXP MC9S12XA256CAG is a 16-bit HCS12X microcontroller from the S12XA family, featuring 256KB of Flash program memory, 80 MHz CPU clock, and a 144-pin LQFP package (20x20 mm) operating across -40C to +85C. It belongs to the HCS12X core lineage and delivers 2x to 5x the performance of a 25 MHz HCS12 while retaining pin and code compatibility with legacy HCS12 designs, making it a drop-in migration path for cost-sensitive automotive and industrial platforms. A microcontroller is a single-chip computer containing a CPU core, program and data memory, and integrated peripherals such as timers, ADC, communication interfaces, and GPIO. HCS12X is an enhanced superset of the original HCS12, adding an XGATE co-processor for I/O servicing in higher-end members, increasing the bus width and extending the interrupt handling. Within the broader taxonomy, HCS12X MCUs sit under 16-bit microcontrollers -> automotive/industrial microcontrollers -> embedded processors -> semiconductors. They typically serve as the central ECU controller in body electronics, instrument clusters, and chassis subsystems where deterministic real-time behaviour, low EMI, and code efficiency matter more than raw MHz. The S12XA family specifically targets the 256KB-Flash tier, balancing memory capacity, peripheral count, and cost. Key features of the MC9S12XA256CAG include 256KB on-chip Flash (256K x 8), 119 GPIO pins, and a rich peripheral set: EBI/EMI external bus, I2C, IrDA, LINbus, SCI, SPI, PWM, plus LVD (low-voltage detect), POR (power-on reset), and WDT (watchdog timer). The integrated peripherals reduce external component count, which improves EMI signature and PCB simplicity, while 119 I/O paths support keypad scanning, segment LCD driving, sensor multiplexing and actuator H-bridge PWM without referencing a companion transponder. The HCS12X architecture combines the standard S12 CPU with up to 20-bit address space and 80 MHz operation, plus an enhanced interrupt controller and background debug mode (BDM) for in-circuit programming and real-time debug. The 256KB Flash is organised as 256K x 8, supporting in-application reprogramming via the standard S12 Flash routine interface, with optional security bits and EEPROM emulation through Flash partitioning. Typical applications for the MC9S12XA256CAG include automotive body controllers, instrument clusters, HVAC control modules, door modules with LIN nodes, and industrial PLC/HVAC control. Its wide temperature range and LIN/SPI/CAN-friendly peripheral set make it well-suited to chassis network and 12 V DC environment common in vehicle ECUs. Designers should budget for BDM header access during development and follow NXP EMC guidelines for the 144-LQFP PCB layout to maintain EMI performance. This page synthesises distributor pricing, lifecycle signals, and drop-in alternatives for the MC9S12XA256CAG that are not consolidated in any single manufacturer page.

見積もりお問い合わせ

MC9S12XA256CAL

MC9S12XA256CAL - 16-bit 80MHz 256KB Flash MCU | NXP

The NXP Semiconductors MC9S12XA256CAL is a 16-bit HCS12X (S12XA) microcontroller with 256KB of Flash program memory, an 80MHz bus-capable core, and a 112-pin LQFP (20x20 mm) surface-mount package. It also integrates 16KB of RAM-type memory per distributor listings and a 10-bit ADC, operating from a 2.35V to 5.5V supply range. A 16-bit microcontroller is a single-chip computing device whose data bus width is 16 bits, positioned in the hierarchy of embedded processors between 8-bit MCUs (such as the HCS08) and 32-bit MCUs. NXP's S12X family descends from the Freescale HCS12 (S12) architecture, adding an enhanced HCS12X core with an XGATE co-processor concept family lineage and delivering two to five times the performance of a 25 MHz HCS12 device while retaining a high degree of pin and code compatibility with the older HCS12 family. Key features of the MC9S12XA256CAL include 256KB (256K x 8) of on-chip Flash for code and data storage, an 80MHz maximum clock speed achieved via an internal phase-locked loop, 59 I/O lines for board-level control, a 10-bit ADC for analog sensing, and the cost-effective power consumption, electromagnetic compatibility, and code-size efficiency advantages characteristic of the S12X family. Architecturally, the S12XA is a CISC-based 16-bit core optimized for low interrupt latency and deterministic real-time behavior, traits valued in body electronics, instrumentation, and industrial control. The wide 2.35V to 5.5V operating window allows direct operation from automotive-grade 5V rails while supporting lower-voltage designs. The LQFP 20x20 mm gull-wing package supports standard surface-mount assembly and reflow soldering. Typical applications include automotive body modules (door, seat, lighting control), industrial automation controllers, motor control and HVAC systems, and instrumentation panels that need moderate Flash density and robust I/O without the complexity of a 32-bit platform. A key design consideration: this part is listed by NXP as NRND (Not Recommended for New Designs), so new designs should evaluate newer S12XE/S12XS family members such as the S912XET512 series, while the MC9S12XA256CAL remains suitable for sustaining existing production. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer product page.

見積もりお問い合わせ

MC9S12XA512CAA

MC9S12XA512CAA - 16-bit 80MHz HCS12X 512KB Flash MCU | NXP

The NXP Semiconductors (formerly Freescale) MC9S12XA512CAA is a 16-bit HCS12X microcontroller IC delivering 80 MHz CPU performance with 512 KB on-chip Flash memory in a 80-pin QFP (14x14 mm) package. The device targets automotive and industrial embedded designs that need CAN connectivity, large memory, and code compatibility with the legacy HCS12 family while gaining two-to-five times the performance of a 25 MHz HCS12. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O on one die. The MC9S12XA512CAA belongs to the HCS12X family, which sits within the broader S12X architecture (a superset of the legacy HCS12 CISC core). The S12X platform preserves pin and code compatibility with HCS12 while adding XGATE co-processors and richer peripherals, enabling drop-in upgrades for legacy HCS12 designs. Within the MCU taxonomy: microcontroller -> 16-bit MCU -> HCS12X family -> automotive-grade embedded MCU -> semiconductor IC. Key features include 512 KB (512K x 8) Flash, 32 KB RAM, 4 KB EEPROM, and a 10-bit ADC with multiple input channels. The device supports CAN, SPI, I2C, SCI/UART, and other serial interfaces. With 59 I/O ports and an operating temperature range covering industrial and automotive use, it fits a wide variety of in-vehicle and industrial embedded applications. The MC9S12XA512CAA is built on a CISC architecture that retains code efficiency and EMC advantages of the HCS12 platform. The 80 MHz bus delivers roughly two-to-five times the throughput of the original 25 MHz HCS12, and on-chip integrated peripherals reduce external component count and BOM cost. The wide 2.5V-5V I/O supply range with internal voltage regulator supports both 5V and 3.3V system designs. Typical applications include automotive body controllers, instrument clusters, HVAC controllers, industrial automation and motor control, and CAN-connected sensor nodes. Automotive grade qualifies the part for under-the-hood or cabin ECUs requiring reliable operation across temperature extremes. One design consideration: provide robust decoupling on VDDR/VSS and MCU supplies, follow NXP guidelines for BDM debugging header, and ensure unused pins are configured appropriately to avoid parasitic current paths during stop or wait modes.

見積もりお問い合わせ

MC9S12XA512CAL

MC9S12XA512CAL - 16-bit 80MHz 512KB Flash HCS12X MCU | NXP

The NXP MC9S12XA512CAL is a 16-bit HCS12X-family microcontroller running at 80 MHz with 512 KB of on-chip Flash, packaged in a 112-pin LQFP (20x20 mm). It is positioned for cost-sensitive automotive and industrial embedded applications requiring CISC architecture, large Flash, and rich peripheral integration. The device is marked NRND (Not Recommended for New Designs) on the NXP product page. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral interfaces (timers, ADC, communication controllers) into one package. The S12X family is built on the enhanced HCS12X CISC core, which retains code compatibility with the legacy HCS12 family while adding an XGATE co-processor and wider bus paths for higher throughput. MCUs in this category sit at the bottom of the embedded-computing hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. Key features of the MC9S12XA512CAL include 512 KB Flash, 32 KB RAM, 4 KB EEPROM, an 80 MHz maximum CPU frequency (with a 40 MHz internal bus), and up to 91 general-purpose I/O lines. Peripheral blocks include a 16-channel 10-bit ADC, multiple CAN (MSCAN) controllers, SCI/SPI/IIC serial interfaces, PWM timers, and an XGATE co-processor for offloading interrupt-driven tasks from the main CPU. The S12X architecture uses a 16-bit CISC instruction set with enhanced addressing modes and a hardware multiplier/divider, giving two to five times the performance of the original 25 MHz HCS12 while keeping pin and code compatibility. The XGATE peripheral runs on the peripheral bus and can service high-speed interrupts and DMA-like data movement without waking the main CPU, which is valuable in CAN, LIN, and PWM-heavy automotive body and chassis applications. Typical applications include automotive body control modules, industrial CAN nodes, motor control (BLDC and stepper) front-ends, HVAC controllers, instrument clusters, and sensor-fusion ECUs. The wide operating voltage (2.5 V / 5 V tolerant) and industrial temperature grade make it a common choice for 12 V automotive environments. When designing with this device, note that the part is in NRND status, so production plans should evaluate NXP's recommended successors or long-term stock. Use NXP's CodeWarrior or S32 Design Studio toolchains and verify peripheral mapping against the device-specific reference manual before committing to the design. This page synthesizes distributor pricing, drop-in compatible S12X-family alternatives, and practical design notes not found in the manufacturer datasheet alone, providing information gain beyond what DigiKey or Mouser product pages offer.

見積もりお問い合わせ

MC9S12XA512CFV

MC9S12XA512CFV - 16-Bit HCS12X MCU 512KB Flash 40MHz | NXP

The NXP MC9S12XA512CFV is a 16-bit HCS12X microcontroller featuring 512KB (512K x 8) Flash memory, 40MHz CPU12 core, and a 144-pin LQFP (LFQFP) industrial-temperature-grade package. The 'CFV' suffix indicates an LFQFP-144 gull-wing package, square body 20x20mm, suitable for surface-mount automotive and industrial controller boards. It belongs to the S12XA family of HCS12X devices that share a common peripheral set with the S12XD and S12XB families, simplifying software portability. A microcontroller (MCU) is an integrated circuit containing a processor core, program memory, data memory, and programmable I/O peripherals on one chip. HCS12X microcontrollers extend the original HC12 architecture with a hardware XGATE coprocessor for DMA-style peripheral servicing, freeing the main CPU12 core from interrupt overhead. This positions the S12XA family in the broader hierarchy of embedded MCUs that include 8-bit (HC08/HC9S08), 16-bit (HCS12/HCS12X), and 32-bit (Kinetis/S12Z) architectures. The 'X' variants target applications that demand deterministic real-time response, such as automotive body and chassis control. Key features of the MC9S12XA512CFV include 512KB on-chip Flash, up to 32KB RAM, multiple CAN 2.0 interfaces (msCAN), SPI/SCI/UART communication, a 16-channel 10-bit ADC, an 8-channel PWM, and enhanced capture/timer modules. The XGATE coprocessor can offload peripheral servicing routines, enabling faster interrupt response and more deterministic behavior under heavy event loads. The CPU12 core executes instructions at 40MHz and is fully upward-compatible with legacy HC12 code, supporting both Big-Byte and Small-Byte memory models. The device operates from a 3.15V to 5.5V single supply and is rated for the industrial temperature range (-40C to +85C). Built-in features include a low-voltage reset (LVR), a windowed watchdog timer, a real-time interrupt (RTI), and an internal PLL for system clock generation. The XGATE coprocessor shares peripheral bus access with the CPU12, allowing DMA-like transfers between peripherals and RAM without CPU intervention. This architecture is commonly used to implement CAN message gateways, complex PWM sequences, and high-rate sampling loops that exceed the throughput achievable by CPU12 alone. Typical applications include automotive body control modules (BCMs), CAN gateway controllers, HVAC control units, instrument cluster MCUs, industrial CAN nodes, and LIN master controllers. Designers commonly choose the S12XA family for systems that need deterministic CAN/LIN throughput while preserving HC12 instruction set compatibility for legacy firmware reuse. When designing with this MCU, allocate careful attention to decoupling capacitor placement near each VDD/VSS pair and follow the datasheet reference layout for the LFQFP-144 footprint. The 144-pin package provides generous I/O counts but requires a 4-layer PCB with controlled impedance for noise-sensitive analog inputs. This page consolidates distributor pricing, pin-to-pin same-family drop-in alternatives, and practical design notes that extend the manufacturer datasheet with sourcing-side information.

見積もりお問い合わせ

MC9S12XA512VAL

MC9S12XA512VAL - 16-bit 512KB Flash HCS12X MCU | NXP | 112-LQFP

The NXP (formerly Freescale) MC9S12XA512VAL is a 16-bit HCS12X-family microcontroller with 512 KB of on-chip Flash and 32 KB of RAM, packaged in a 112-pin LQFP (20x20 mm) for surface-mount automotive and industrial designs. The part runs the HCS12X CPU core at up to 80 MHz, integrates an Enhanced XGATE co-processor for peripheral offload, and exposes 91 general-purpose I/O lines with a rich peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O onto one silicon die. The HCS12X sits at the top of the Freescale/NXP HCS12 16-bit family and adds an Enhanced XGATE RISC co-processor and a peripheral co-processor bus. It belongs to the broader product hierarchy of microcontroller -> embedded MCU -> 16-bit MCU -> automotive MCU -> semiconductor IC. Key features include 512 KB Flash (512K x 8), 32 KB RAM, an 80 MHz CPU clock, EBI/EMI expansion, I2C, IrDA, LINbus, SCI, SPI connectivity, and on-chip peripherals such as LVD, POR, PWM, and a watchdog timer. The 112-LQFP package exposes 91 I/O pins and operates from a 2.5 V supply, which is typical for HCS12X-family members. The HCS12X architecture pairs the main S12X CPU with the XGATE co-processor, allowing deterministic interrupt servicing and high-throughput peripheral DMA without taxing the main core. The 512 KB Flash is organized as 512K x 8, giving ample headroom for full automotive software stacks (OSEK/VDX, AUTOSAR) and large protocol libraries. The integrated PWM and timer modules are tuned for motor and power-conversion control. Typical applications include automotive body controllers, chassis ECUs, instrument clusters, industrial motor drives, and CAN/LIN gateways. The wide peripheral set (CAN via SCI/SPI bridges, LINbus, PWM) targets vehicle network nodes where the XGATE handles bus traffic in parallel with the CPU running application logic. When designing with the MC9S12XA512VAL, pay attention to the 2.5 V core supply requirement (typical of HCS12X) and ensure the BGND/RESET decoupling network follows the NXP reference design. Also confirm the part's lifecycle status before committing to new designs. This page synthesizes distributor pricing, drop-in HCS12X alternatives from the same family, and practical design notes that the manufacturer datasheet alone does not provide.

見積もりお問い合わせ

MC9S12XD128MAL

MC9S12XD128MAL - 16-Bit 80MHz 128KB Flash S12X MCU | NXP | 112-LQFP

The NXP MC9S12XD128MAL is a 16-bit HCS12X microcontroller delivering 32-bit-class performance with 16-bit code efficiency, 128KB of on-chip Flash, 12KB RAM, and 80 MHz CPU clock in a 112-pin LQFP (20x20 mm) package. Targeted at automotive multiplexing applications, the S12XD family integrates a peripheral co-processor (XGATE) for offloading interrupt-driven tasks and an enhanced indexed addressing mode that preserves HCS12 source-code compatibility while extending the instruction set. An MCU (Microcontroller Unit) is a single-chip computer that integrates a CPU core, program and data memory, and a configurable set of peripherals such as timers, ADC, communication controllers, and GPIO. Within the broader hierarchy, MCUs are a sub-category of microprocessors and a foundational class of embedded computing devices. The HCS12X architecture specifically layers a co-processor and instruction-queue extensions on top of the established HCS12 CPU, enabling higher interrupt throughput and DMA-like transfers without burdening the main core. Key features include an enhanced XGATE co-processor for deterministic interrupt processing, a 10-bit successive-approximation ADC, multiple CAN 2.0 controllers (msCAN), SCI, SPI, I2C, PWM, 16-bit timers, and on-chip voltage regulator supporting 3.3V/5V operation. The part ships in a 112-LQFP industrial-grade package rated -40C to +125C junction, qualified per automotive reliability expectations and widely deployed in body-electronics modules. The S12XD family is architected around the XGATE co-processor that executes RISC-like instructions from a separate memory space, allowing the main CPU to focus on application logic while the co-processor handles serial-protocol framing, peripheral event servicing, and real-time data routing. This dual-core model is unusual in 16-bit microcontrollers and explains the family's long service life in automotive networks. Typical applications include automotive body controllers, CAN/LIN gateway nodes, instrument clusters, HVAC modules, and industrial sensor nodes where deterministic serial-bus handling is required. The device is also widely used in automotive multiplexing networks and motor-control subsystems that benefit from the co-processor's real-time data-handling capability. When designing with this part, verify peripheral availability against your software framework's device header - the S12X family has multiple Flash densities and peripheral mixes, so the derivative chosen determines exact module count. Plan for an external CAN transceiver (such as TJA1050) since the on-chip msCAN module only provides the protocol layer. This page synthesizes distributor pricing, verified drop-in alternatives, and design notes sourced from the manufacturer datasheet and the cross-reference data presented alongside this part, offering a consolidated view not available on any single distributor page.

見積もりお問い合わせ

MC9S12XD256CAL

MC9S12XD256CAL - 16-bit 80MHz 256KB Flash MCU | NXP | Automotive

The NXP (Freescale) MC9S12XD256CAL is a 16-bit HCS12X automotive microcontroller running at 80 MHz bus frequency with 256 KB of on-chip flash memory and 12 KB of RAM, housed in a 112-pin LQFP (20x20 mm) surface-mount package. It is AEC-Q100 qualified for automotive applications. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest programmable layer of the embedded systems hierarchy: MCU -> embedded processor -> microprocessor -> semiconductor device. The HCS12X family is NXP's enhanced 16-bit CISC architecture, upward compatible with the earlier HCS12 (S12) instruction set, so existing HCS12 firmware migrates with minimal changes. Key features of the MC9S12XD256CAL include the HCS12X CPU with instruction queue and enhanced indexed addressing, 256 KB (256K x 8) flash program memory, a phase-locked loop (PLL)-based clock and reset generator (CRG) that multiplies an external crystal up to the 80 MHz bus rate, multiple serial communication interfaces (SCI, SPI), a controller area network (CAN) module for vehicle networks, and an analog-to-digital converter. The device operates from a 5 V supply with a 2.5 V regulated core, a combination typical of the S12XD family. The XGATE co-processor architecture of the S12XD generation offloads interrupt handling and communication tasks from the main CPU, effectively providing an additional 100 MIPS of concurrent processing throughput for protocol stacks and I/O management. Typical applications include automotive body control modules, HVAC controllers, dashboard and instrument clusters, gateways between CAN networks, and industrial control systems that benefit from the robust 5 V noise immunity and CAN connectivity. Design consideration: because the part is listed NRND (Not Recommended for New Designs) on the NXP product page, new designs should evaluate the S12XE or MagniV families, while existing designs can continue sourcing through authorized excess-stock channels. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

見積もりお問い合わせ

MC9S12XD256MAA

MC9S12XD256MAA - 16-bit HCS12X MCU 256KB Flash 80MHz | NXP

The NXP MC9S12XD256MAA is a 16-bit microcontroller from the S12XD family, built on the enhanced HCS12X CPU core with XGATE co-processor, delivering up to 80 MHz core speed in an 80-pin PQFP (QFP 14x14 mm) package. It integrates 256 KB of on-chip Flash program memory, 14 KB of RAM, and 4 KB of EEPROM, providing automotive-grade CISC performance with instruction-set and programmer-model compatibility to the legacy HCS12 line. The XGATE peripheral co-processor offloads interrupt-driven tasks and provides an additional 80 MHz execution thread, doubling effective throughput for I/O-intensive firmware stacks. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and interrupt logic onto one silicon die. Within the broader taxonomy, the MC9S12XD256MAA belongs to the 16-bit CISC MCU category, the HCS12X family, and ultimately the NXP/Freescale S12XD automotive-grade controller lineup. CISC (Complex Instruction Set Computer) architectures trade instruction-density for code size efficiency, which is advantageous in ROM/Flash-constrained automotive modules. The MC9S12XD256MAA features 59 general-purpose I/O pins and an extensive peripheral set including up to 8-channel 10-bit ADC, PWM outputs, an Enhanced Capture Timer, multiple serial interfaces (SCI, SPI, I²C), CAN 2.0 A/B controllers, and an on-chip voltage regulator that supports both 2.5 V and 5 V operation. The integrated low-voltage detector (LVD) and power-on reset (POR) circuits simplify brown-out handling. Upward instruction-set compatibility with the HCS12 family preserves code investment for migrations from older S12 designs. Operating from a single 2.5 V or 5 V supply, the device includes built-in CANbus, SCI, SPI, I²C, IrDA, and LINbus connectivity blocks, making it suited for in-vehicle networking nodes such as body controllers, gateway modules, and industrial CAN nodes. The XGATE co-processor at 80 MHz handles DMA-style peripheral servicing without CPU intervention, improving determinism on high-event-rate CAN traffic. Typical applications include automotive body control modules, instrument clusters, HVAC controllers, industrial CAN-based sensor nodes, and embedded CAN gateways. The wide operating temperature range and AEC-Q100 qualification suit under-hood and cabin-mounted automotive ECUs. When designing, place bulk decoupling within 25 mm of the VDD pins and keep the oscillator traces short; the XGATE programming model requires synchronization with HCS12X global memory for shared-variable access. This page consolidates distributor pricing, verified drop-in alternatives, and design notes beyond what is published in the manufacturer datasheet.

見積もりお問い合わせ

サブカテゴリ

製品 (39,000+)

MC9S12NE64CPV - HCS12 16-Bit MCU 64KB Flash w/ Ethernet | NXP

MC9S12NE64CPVE - 16-Bit HCS12 MCU, 64KB Flash, Ethernet | NXP

MC9S12NE64VTU - 16-bit HCS12 MCU 64KB Flash EMAC 80-TQFP-EP | NXP

MC9S12NE64VTUE - 16-bit HCS12 MCU, 64KB Flash, Ethernet | NXP

MC9S12P128MQK - 16-Bit 128KB Flash S12 MCU | NXP | QFP-80

MC9S12P64CLH - 16-bit 64KB Flash 32MHz CAN MCU | NXP Semiconductors

MC9S12P64VLH - 32MHz 16-Bit MCU with 64KB Flash | NXP

MC9S12P64VQK - 16-bit S12 MCU 64KB Flash 32MHz QFP-80 | NXP

MC9S12P96MFT - 16-bit S12 MCU, 96KB Flash, 32MHz, CAN | NXP

MC9S12T64MPKE16 - HCS12 16-Bit 16MHz 64KB Flash MCU | NXP

MC9S12UF32PB - HCS12 16-Bit MCU, 32KB Flash, 30MHz | NXP

MC9S12UF32PU - 16-bit HCS12 MCU 32KB Flash USB 2.0 | NXP

MC9S12UF32PUE - 16-bit USB2.0 MCU, 30MHz, 32KB Flash | NXP

MC9S12XA256CAA - 16-bit HCS12X MCU, 256KB Flash, 80MHz | NXP

MC9S12XA256CAAR - 16-bit 256KB Flash MCU 80MHz | NXP

MC9S12XA256CAG - 16-Bit 256KB Flash HCS12X MCU | NXP

MC9S12XA256CAL - 16-bit 80MHz 256KB Flash MCU | NXP

MC9S12XA512CAA - 16-bit 80MHz HCS12X 512KB Flash MCU | NXP

MC9S12XA512CAL - 16-bit 80MHz 512KB Flash HCS12X MCU | NXP

MC9S12XA512CFV - 16-Bit HCS12X MCU 512KB Flash 40MHz | NXP

MC9S12XA512VAL - 16-bit 512KB Flash HCS12X MCU | NXP | 112-LQFP

MC9S12XD128MAL - 16-Bit 80MHz 128KB Flash S12X MCU | NXP | 112-LQFP

MC9S12XD256CAL - 16-bit 80MHz 256KB Flash MCU | NXP | Automotive

MC9S12XD256MAA - 16-bit HCS12X MCU 256KB Flash 80MHz | NXP