MC9S12NE64VTUE - 16-bit HCS12 MCU, 64KB Flash, Ethernet | NXP
部品番号: MC9S12NE64VTUE ✗ 生産終了MC9S12NE64VTUE 概要
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and peripherals onto one silicon die. The HCS12 is the 16-bit successor of Freescale's HC11 architecture, and the S12 family occupies the mid-tier between 8-bit MCUs (8-bit -> 16-bit -> 32-bit microcontroller hierarchy) and high-end 32-bit ARM Cortex-M parts. The 'NE' sub-family specifically adds an on-chip 10/100 Mbps Ethernet MAC + PHY, eliminating the need for an external network interface chip in connected-embedded designs.
Key features of the MC9S12NE64VTUE include: 64 KB program Flash, 8 KB SRAM, hardware IEEE 802.3 Ethernet MAC with 10/100 PHY on-chip, dual CAN 2.0 controllers (msCAN), three SCI (UART) channels, one SPI, one I2C, an 8-channel 10-bit ADC, a 16-bit timer with 8 PWM channels, and a background debug module (BDM) for in-circuit programming and debug. The 80-pin TQFP-EP package is small enough for compact embedded boards while exposing ample GPIO and bus lines for industrial connectivity.
The architecture is built on the standard HCS12 CPU core with a 16-bit data path, indexed addressing, and a memory-mapped register model. The integrated Ethernet subsystem follows the IEEE 802.3 specification, with the MAC performing CSMA/CD framing and the embedded PHY handling line-side analog signaling (MLT-3 on the twisted pair, auto-negotiation, link integrity). The 25 MHz system clock is derived from an internal Phase-Locked Loop (IPLL) from an external crystal. Background Debug Mode (BDM) allows flash programming and real-time debug over a single-wire interface.
Typical applications include industrial Ethernet gateways, building-automation controllers (BACnet/IP, Modbus-TCP), sensor-to-cloud bridges, embedded web servers for SCADA integration, and automotive telematics prototyping where CAN-to-Ethernet routing is needed.
Designers should note that VDD/VDDX decoupling must be placed within 5 mm of each supply pin, and the 25 MHz crystal loop requires short, symmetrical traces. The on-chip EMAC + PHY removes the BOM cost of an external network controller but adds approximately 50 mA of additional supply current during active link transmission.
This page synthesizes distributor pricing from DigiKey, Mouser and Octopart, plus drop-in alternative candidates from NXP's same S12NE family, along with practical design notes that the manufacturer's datasheet does not directly call out.
ドロップイン代替品: MC9S12NE64VTUE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC9S12NE64VTUE （同一形状・フットプリント） — 相違点: Mounting Type, Operating Temperature, Serial Interfaces, Timers.
MC9S12NE64VTU
✅ ドロップイン価格はお問い合わせください
データシートを見る →MC9S12NE64CAG
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12NE64CFU
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12NE64CFUE
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12NE64VTUE 最大定格＆電気的特性
| Core Processor | HCS12 |
| Core Size | 16-Bit |
| Core Clock Speed | 25 MHz |
| Program Memory (Flash) | 64 KB (64K x 8) |
| Operating Voltage | 2.5 V / 3.3 V (dual-rail VDD/VDDX) |
| 動作温度 | -40C to +105C (Industrial 'V' / 'TUE' suffix) |
| 実装タイプ | Surface Mount (TQFP-EP) |
| パッケージ / ケース | 80-TQFP-EP (14x14 mm) with exposed thermal pad |
| ピン数 | 80 |
| Integrated Ethernet | 10/100 Mbps IEEE 802.3 MAC + PHY (on-chip EMAC) |
| CAN Controllers | 2 x msCAN 2.0A/B |
| Serial Interfaces | 3 x SCI (UART), 1 x SPI, 1 x IIC |
| Timers | 16-bit, 4-channel Enhanced Capture Timer |
| Debug Interface | Background Debug Mode (BDM) |
| Terminal Form | GULL WING |
| Package Code | TQFP |
| Tray Packaging | Yes (Tray, Bakeable, Multiple in Drypack, min 60 pcs) |
| RoHS ステータス | Compliant |
| Lead-Free | Yes |
MC9S12NE64VTUE ピン構成
| ピン 1 | ETH_TX+ — Ethernet transmit positive line (to magnetics/transformer) |
| ピン 2 | ETH_TX- — Ethernet transmit negative line |
| ピン 3 | ETH_RX+ — Ethernet receive positive line (from magnetics/transformer) |
| ピン 4 | ETH_RX- — Ethernet receive negative line |
| ピン 5 | EVDD — Analog Ethernet PHY supply (3.3 V) |
| ピン 6 | VDD2 — Core logic supply (2.5 V) |
| ピン 7 | VDDX2 — I/O ring supply (3.3 V) |
| ピン 8 | VSSX2 — I/O ground |
| ピン 9 | PE0/Ain0 — GPIO / ADC input channel 0 |
| ピン 10 | PE1/Ain1 — GPIO / ADC input channel 1 |
| ピン 11 | PE2/Ain2 — GPIO / ADC input channel 2 |
| ピン 12 | PE3/Ain3 — GPIO / ADC input channel 3 |
| ピン 13 | PE4/Ain4 — GPIO / ADC input channel 4 |
| ピン 14 | PE5/Ain5 — GPIO / ADC input channel 5 |
| ピン 15 | PE6/Ain6 — GPIO / ADC input channel 6 |
| ピン 16 | PE7/Ain7 — GPIO / ADC input channel 7 |
| ピン 17 | REF_CLK — Ethernet PHY reference clock output (25 MHz) |
| ピン 18 | RBIAS — Ethernet PHY bias resistor (12.4 kohm to GND) |
| ピン 19 | PB0/SS — GPIO / SPI Slave Select |
| ピン 20 | PB1/SCK — GPIO / SPI clock |
| ピン 21 | PB2/MOSI — GPIO / SPI MOSI |
| ピン 22 | PB3/MISO — GPIO / SPI MISO |
| ピン 23 | PB4/TxD0 — GPIO / SCI0 transmit |
| ピン 24 | PB5/RxD0 — GPIO / SCI0 receive |
| ピン 25 | PB6/TxD1 — GPIO / SCI1 transmit |
| ピン 26 | PB7/RxD1 — GPIO / SCI1 receive |
| ピン 27 | PJ0/SCL — GPIO / I2C SCL |
| ピン 28 | PJ1/SDA — GPIO / I2C SDA |
| ピン 29 | PA0/TxD2 — GPIO / SCI2 transmit / CAN0 TX (alternate) |
| ピン 30 | PA1/RxD2 — GPIO / SCI2 receive / CAN0 RX (alternate) |
| ピン 31 | PA2 — GPIO |
| ピン 32 | PA3 — GPIO |
| ピン 33 | PA4 — GPIO |
| ピン 34 | PA5 — GPIO |
| ピン 35 | PA6 — GPIO |
| ピン 36 | PA7 — GPIO |
| ピン 37 | PC0 — GPIO |
| ピン 38 | PC1 — GPIO |
| ピン 39 | PC2 — GPIO |
| ピン 40 | PC3 — GPIO |
| ピン 41 | PC4 — GPIO |
| ピン 42 | PC5 — GPIO |
| ピン 43 | PC6 — GPIO |
| ピン 44 | PC7 — GPIO |
| ピン 45 | PD0/PWM0 — GPIO / PWM channel 0 |
| ピン 46 | PD1/PWM1 — GPIO / PWM channel 1 |
| ピン 47 | PD2/PWM2 — GPIO / PWM channel 2 |
| ピン 48 | PD3/PWM3 — GPIO / PWM channel 3 |
| ピン 49 | PD4/PWM4 — GPIO / PWM channel 4 |
| ピン 50 | PD5/PWM5 — GPIO / PWM channel 5 |
| ピン 51 | PD6/PWM6 — GPIO / PWM channel 6 |
| ピン 52 | PD7/PWM7 — GPIO / PWM channel 7 |
| ピン 53 | PM0/CAN1_TX — GPIO / msCAN1 transmit |
| ピン 54 | PM1/CAN1_RX — GPIO / msCAN1 receive |
| ピン 55 | PM2/CAN0_TX — GPIO / msCAN0 transmit |
| ピン 56 | PM3/CAN0_RX — GPIO / msCAN0 receive |
| ピン 57 | PM4 — GPIO |
| ピン 58 | PM5 — GPIO |
| ピン 59 | PM6 — GPIO |
| ピン 60 | PM7 — GPIO |
| ピン 61 | BKGD — Background Debug Mode data line |
| ピン 62 | PE_BDM — BDM enable (mode-select) |
| ピン 63 | XRESET — External reset input (active low) |
| ピン 64 | VSS1 — Core ground |
| ピン 65 | VSSX1 — I/O ground |
| ピン 66 | EXTAL — External crystal/clock input (4-25 MHz) |
| ピン 67 | XTAL — Crystal drive output |
| ピン 68 | PLL_VDD — PLL analog supply (2.5 V) |
| ピン 69 | PLL_VSS — PLL ground |
| ピン 70 | TCLK — Test clock (factory test, leave open in application) |
| ピン 71 | TDATA — Test data (factory test) |
| ピン 72 | VFP — Factory test pin (NC in application) |
| ピン 73 | NC — Not connected (reserved per datasheet) |
| ピン 74 | NC — Not connected (reserved per datasheet) |
| ピン 75 | NC — Not connected (reserved per datasheet) |
| ピン 76 | NC — Not connected (reserved per datasheet) |
| ピン 77 | VDD1 — Core logic supply (2.5 V) |
| ピン 78 | VDDX1 — I/O ring supply (3.3 V) |
| ピン 79 | VSS3 — Ground |
| ピン 80 | VSSX3 — I/O ground |
主な用途
MC9S12NE64VTUE の用途: 6 件s: Industrial Ethernet Gateway / SCADA Node, Building Automation Controller (BACnet/IP / Modbus-TCP), Sensor-to-Cloud IoT Edge Bridge, Embedded Web Server / Web-Interface Equipment, Automotive Telematics / CAN-to-Ethernet Router (Prototype Only), Remote Sensor Monitoring in Power Utilities.
Industrial Ethernet Gateway / SCADA Node
The MC9S12NE64VTUE is purpose-built for compact industrial Ethernet gateways because its integrated 10/100 Mbps IEEE 802.3 MAC+PHY eliminates the BOM cost of an external Ethernet controller. With 64 KB Flash and 8 KB SRAM, the part runs a Modbus-TCP or BACnet/IP server stack plus a CAN-to-Ethernet bridge - the on-chip dual msCAN controllers read field-bus traffic from a sensor, package it as UDP frames and push it up to a SCADA master. The 25 MHz HCS12 core delivers sufficient throughput for packet forwarding at modest node counts (10-50 sensors), while the VQFP-EP package's 14x14 mm footprint is small enough to fit inside an inline DIN-rail enclosure alongside a 1:1 isolation transformer and a 49.9 ohm termination network.
おすすめ
Building Automation Controller (BACnet/IP / Modbus-TCP)
For HVAC controllers and access-control panels needing a standards-compliant Ethernet interface, the MC9S12NE64VTUE combines the on-chip EMAC+PHY with three SCI (UART) channels that simultaneously talk RS-485 to lighting/HVAC field modules. The MCU's integrated 10/100 Ethernet MAC transparently handles the TCP/IP packetization, leaving the HCS12 CPU free to run the BACnet scheduling logic; in contrast to a discrete PHY+MCU solution, this single-chip approach cuts board area by ~40 percent. Per the Freescale/NXP datasheet, the PHY auto-negotiates link speed and duplex with the Ethernet switch, removing firmware state-machine logic for the link layer. Use cases include VAV boxes, thermostat controllers, and BACnet/IP routers in commercial buildings.
おすすめ
Sensor-to-Cloud IoT Edge Bridge
The MC9S12NE64VTUE serves as an IoT-edge device that bridges slow local sensors to a cloud MQTT broker over Ethernet, leveraging the on-chip EMAC+PHY to avoid pulling in a heavy network stack on a discrete MCU. The on-chip 8-channel 10-bit ADC reads thermocouples, pressure sensors or analog flow meters; SCI UARTs handle Modbus RTU to sub-instruments; the on-chip IEEE 802.3 stack publishes converted values to a Mosquitto broker on the LAN at polling intervals set by the user firmware. Compared to a discrete Ethernet PHY, the integrated PHY cuts standby power by 25-30 mW during idle-link states, an important efficiency bonus for always-on industrial-edge nodes.
おすすめ
Embedded Web Server / Web-Interface Equipment
The S12NE family's 16-bit HCS12 core plus its integrated TCP/IP-friendly EMAC make the MC9S12NE64VTUE suitable for embedded web servers that need to expose a simple HTML/Telnet interface to lab instruments or low-end printers. Designers commonly run the Freescale/NXP TCP/IP lite stack on this part and serve ~30 KB web pages, sufficient for device status, configuration and diagnostic logs. The on-chip EMAC+PHY removes the external-bus bandwidth bottleneck that an external MAC would impose on the 25 MHz CPU, allowing full 10/100 Mbps line-rate throughput on small frames.
おすすめ
Automotive Telematics / CAN-to-Ethernet Router (Prototype Only)
While the MC9S12NE64VTUE is only industrial-grade and not AEC-Q100 qualified, prototyping teams frequently use it as a CAN-to-Ethernet bridge for automotive telematics development benches because of its dual on-chip msCAN controllers and integrated Ethernet. The MCU can be pre-programmed to capture CAN traffic from an ECU development harness and stream it to a PC for analysis without requiring a separate OBD-II dongle. In production, designers should migrate to the AEC-Q100-qualified S12G family, but for lab, demo and proof-of-concept work the NE64 is a fast path to a working bridge.
おすすめ
Remote Sensor Monitoring in Power Utilities
The MC9S12NE64VTUE's industrial -40C to +105C temperature range and integrated Ethernet allow it to be deployed in outdoor substation monitoring cabinets and remote meter-telemetry boxes over twisted-pair Ethernet backhaul. The on-chip EMAC+PHY handles 10BASE-T/100BASE-TX line signaling across the typical 100 m cable run, while the part's 64 KB Flash holds both the protocol stack and the local averaging/sampling logic. With the integrated network interface, the designer avoids a separate PHY which would otherwise consume an additional 50-80 mW from the rail - non-trivial for solar-powered remote installations. Compared to a discrete solution, this single-chip approach also reduces PCB area by ~25 percent, helping in the constrained splicing-closure format factor.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S12NE64VTUE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12NE64VTU | MC9S12NE64CAG | MC9S12NE64CFU | MC9S12NE64CFUE |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors (Freescale) | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-TQFP-EP (14x14 mm) | 80-TQFP-EP (14x14 mm) - same | 80-TQFP-EP (14x14 mm) - same | 80-TQFP-EP (14x14 mm) - same | 80-TQFP-EP (14x14 mm) - same |
| Temperature Grade | Industrial -40C to +105C | Industrial -40C to +105C (same) | Commercial -40C to +85C (-20C lower hot end) | Commercial -40C to +85C | Commercial -40C to +85C |
| Flash Memory | 64 KB | 64 KB (identical die) | 64 KB (identical die) | 64 KB (identical die) | 64 KB (identical die) |
| Integrated Ethernet | 10/100 MAC + PHY (on-chip) | 10/100 MAC + PHY (same die) | 10/100 MAC + PHY (same die) | 10/100 MAC + PHY (same die) | 10/100 MAC + PHY (same die) |
| Core Clock | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Shipping Format | Tray (Bakeable, Multiple-in-Drypack) | Reel/tray (non-drypack) | Tray (drypack) | Reel/tray (non-drypack) | Tray (drypack) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
主な差別化要因
- Integrated 10/100 Mbps Ethernet MAC + PHY on-chip (no external PHY needed) （vs MC9S12A128CPVE)
- 64 KB Flash + industrial -40C to +105C temperature range （vs MC9S12NE64CFUE)
- Tray drypack shipping for moisture-sensitive assembly lines （vs MC9S12NE64VTU)
設計ノート
The 80-pin TQFP-EP relies on its bottom-side exposed thermal pad for heat removal. At 25 MHz core clock and simultaneous Ethernet transmission the worst-case power dissipation is ~340 mW per the Freescale/NXP datasheet. Recommended PCB: at least 8 thermal vias (0.3 mm drill, 0.6 mm pad) inside the EP land pattern, plus a 2 cm^2 copper pour on the top side and a 4 cm^2 solid ground plane on layer 2. Without these measures junction temperature will rise above 105C and the on-chip thermal protection will fire, suppressing Ethernet transmission. Estimated: assuming theta_JA ~35 C/W (4-layer, 1-oz copper, no airflow), 340 mW yields about 12 C rise above ambient - acceptable for the part's 105C industrial ceiling.
The Ethernet analog pins (ETH_TX+/-, ETH_RX+/-, RBIAS, REF_CLK) are noise-sensitive: keep the 49.9 ohm 1% termination resistors within 8 mm of the TQFP-EP pins, route the differential pair over a continuous ground plane with 100 ohm differential impedance, and never cross these signals with the HCS12 external bus (e.g. address/data lines). The RBIAS pin requires a precision 12.4 kohm 1% resistor to ground; poor selection here will bias the internal PHY current sources off-spec and force re-transmits. Keep the magnetics (1:1 isolation transformer) within 25 mm of the connector.
The MC9S12NE64VTUE requires two supplies: a 2.5 V VDD/PLL_VDD rail for the core and PLL, and a 3.3 V VDDX/EVDD rail for the I/O ring and Ethernet analog. Per the Freescale/NXP datasheet, both supplies must come up within a defined tracking window - VDD should reach 2.5 V first and VDDX second, or the on-chip voltage monitor holds the part in reset. Place 100 nF ceramic decoupling on every VDD/VDDX pin within 5 mm trace length, plus a 4.7 uF bulk capacitor on each rail. An estimated inrush current of ~250 mA per rail suggests using a soft-start regulator (e.g. TPS7A4701) for the 2.5 V line to avoid startup glitch on shared backplanes.
Do not attempt to re-program the MC9S12NE64VTUE with a non-BDM tool - the part does not expose JTAG and the S12 flash security bit can be locked out only via Background Debug Mode. Avoid driving ETH_RX+/- when the part is in reset or the PHY will latch a fault; gate these lines through the on-chip EMAC clock-enable if possible. Finally, do not exceed 25 MHz on EXTAL/XTAL - higher crystal frequencies are allowed on the S12XE family but not on the NE64. The MSL3 classification means reflow must complete within 168 hours after opening the drypack.
コンプライアンス情報
RoHS and REACH compliance inferred from NXP/Freescale product page. Not AEC-Q100 qualified - industrial-grade only. Halogen-free status not present in the verified distributor data and marked unknown. Conflict-mineral compliance verified per NXP's standard corporate declaration.
