AD544LH - Precision BiFET Op Amp, 25 pA Max | Analog Devices
部品番号: AD544LH ✗ 生産終了AD544LH 概要
A BiFET operational amplifier is a voltage-amplifier IC whose input stage uses field-effect transistors to produce very low input bias current. Within the signal-chain hierarchy, the AD544LH belongs to the family of precision amplifiers used for current-to-voltage conversion, instrumentation, buffering, and feedback control. Its low-bias input characteristic is especially useful when the source impedance is high and the amplifier must avoid loading the sensing node.
The AD544 family uses precision monolithic BiFET construction combined with laser trimming for offset-voltage control. Key characteristics include one amplifier function, a maximum offset voltage of 500 uV for the AD544LH grade, and a maximum bias current of 25 pA when warmed up. The L grade operates from 0°C to +70°C, while the S grade in the same family covers -55°C to +125°C.
All devices in the AD542, AD544, and AD547 series are offered in the hermetically sealed TO-99 metal can package. This construction supports use in older instrumentation, industrial analog interfaces, and precision measurement equipment where a conventional eight-lead metal-can footprint is already established on the board.
Typical applications include precision transimpedance amplifiers, guarded sensor amplifiers, low-level signal conditioning, laboratory measurement systems, and industrial process-control interfaces. The low bias current helps preserve small sensor signals, while the trimmed offset limits input-referred error when the signal is amplified through high gain.
When designing a replacement circuit, confirm the eight-pin TO-99 pin arrangement, supply voltage, common-mode range, output swing, and stability requirements before substitution. Keep sensitive input-node routing short, use a clean ground reference, and verify that the selected grade covers the intended ambient temperature range.
ドロップイン代替品: AD544LH — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: AD544LH (同一形状・フットプリント) — 相違点: Maximum Input Bias Current, Operating Temperature Range.
AD544JH
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD544SH
✅ ドロップイン価格はお問い合わせください
データシートを見る →AD544KH
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD547LH
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →AD542JH
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD544LH 最大定格&電気的特性
| Amplifier Type | Precision operational amplifier |
| Number of Channels | 1 channel |
| Input Stage Technology | BiFET field-effect transistor input |
| Maximum Input Bias Current | 25 pA max, warmed up |
| Maximum Input Offset Voltage | 500 uV max |
| Offset Voltage Adjustment Method | Laser trimmed |
| Grade | L commercial grade |
| 動作温度範囲 | 0°C to +70°C |
| Package Type | TO-99 hermetically sealed metal can, MBCY8 |
| Package Pin Count | 8 pins |
| 実装スタイル | Through-hole |
AD544LH 8 pins ピン配置ガイド
AD544LH (8 pins パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD544LH.
詳細は データシート をご参照ください。
主な用途
AD544LH の用途: 6 件s: Precision Transimpedance Amplification, High-Impedance Instrumentation Amplifier Input, Low-Level Process Signal Conditioning, Precision Buffering and Level Shifting, Laboratory and Instrumentation Measurement, Legacy High-Reliability Analog Retrofit.
Precision Transimpedance Amplification
The AD544LH fits a transimpedance stage for photodiode, electrochemical-cell, or other current-source sensing because its maximum input bias current is 25 pA when warmed up. Placing the amplifier in the familiar inverting configuration allows the feedback resistor to convert sensor current into a measurable voltage while the low-bias input stage minimizes disturbance of the source. The 500 uV maximum offset specification also supports low-level current measurements. Confirm the feedback-resistor value, compensation method, and signal bandwidth in the AD544 data sheet because transimpedance stability depends on total input capacitance and noise gain rather than bias current alone.
High-Impedance Instrumentation Amplifier Input
The AD544LH is appropriate for the first stage of a precision instrumentation interface when the source presents high impedance. Its BiFET input stage draws no more than 25 pA of bias current when warmed up, reducing loading errors on sources such as strain gauges, glassy-carbon electrodes, and capacitive sensors. The L-grade device covers 0°C to +70°C, while its laser-trimmed offset voltage is limited to 500 uV. In a multi-amplifier design, verify common-mode voltage limits, input capacitance, noise performance, and stability for the intended gain before finalizing resistor and capacitor values.
Low-Level Process Signal Conditioning
The AD544LH can condition low-amplitude analog signals from industrial process-control equipment where the input source is high impedance and error current must remain small. A 25 pA maximum bias current helps preserve weak sensor outputs, and the laser-trimmed offset reduces input-referred error in high-gain stages. The hermetically sealed TO-99 package is useful in legacy or high-reliability control systems that already use this metal-can footprint. For new equipment, check supply-voltage limits, common-mode range, output drive, and operating-temperature requirements against the complete AD544 electrical tables before schematic release.
Precision Buffering and Level Shifting
The AD544LH works as a unity-gain buffer or precision level-shifting stage when a high-impedance source cannot drive the next circuit directly. The low-bias BiFET input avoids charging errors at the source node, while the single-channel configuration and eight-pin TO-99 package simplify retrofitting into older analog boards. A buffer application depends on stable operation across the expected output load and common-mode range, so use the data-sheet load-capacitance and stability information when adding cable or sampling capacitance. Place the buffer close to the source and keep the feedback connection compact to minimize added noise and instability.
Laboratory and Instrumentation Measurement
The AD544LH is suited to laboratory measurement front ends that evaluate small currents or voltages from precision sensors. Its maximum input bias current of 25 pA when warmed up is valuable when the measurement source has high resistance, and the laser-trimmed offset characteristic supports predictable DC behavior after warm-up. The TO-99 hermetically sealed package can also suit legacy measurement platforms designed around the MBCY8 footprint. Specify warm-up time, input bias-current temperature behavior, and acceptable offset error for the measurement specification. Use guarding and short PCB input routes to prevent leakage from degrading the result.
Legacy High-Reliability Analog Retrofit
The AD544LH provides a practical retrofit option for legacy analog systems that use an eight-pin hermetically sealed TO-99 precision-amplifier footprint and require very low input bias current. Its BiFET input stage and 25 pA maximum warmed-up bias current suit existing sensor and feedback networks, while the TO-99 construction can help preserve reliability in established industrial platforms. Confirm that the replacement matches the original pinout, supply polarity, common-mode range, and output-load capability. Also compare the L-grade 0°C to +70°C range with the original component’s qualification before using it in equipment exposed to wider temperatures.
エンジニアリング参考データ: AD544LH — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD544JH | AD544KH | AD544SH | AD547LH | AD542JH |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TO-99 hermetically sealed metal can, MBCY8 | TO-99 hermetically sealed metal can, MBCY8 | TO-99 hermetically sealed metal can, MBCY8 | TO-99 hermetically sealed metal can, MBCY8 | TO-99 hermetically sealed metal can, MBCY8 | TO-99 hermetically sealed metal can, MBCY8 |
| Amplifier Function | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Input Stage | Precision monolithic BiFET | Precision monolithic BiFET | Precision monolithic BiFET | Precision monolithic BiFET | Precision monolithic BiFET | Precision monolithic BiFET |
| Maximum Input Bias Current | 25 pA max, warmed up | 25 pA max, warmed up | 25 pA max, warmed up | 25 pA max, warmed up | 25 pA max, warmed up | 25 pA max, warmed up |
| Operating Temperature Range | 0°C to +70°C | 0°C to +70°C | 0°C to +70°C | -55°C to +125°C | 0°C to +70°C | 0°C to +70°C |
| Offset Adjustment Method | Laser trimmed | Laser trimmed | Laser trimmed | Laser trimmed | Laser trimmed | Laser trimmed |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
主な差別化要因
- Commercial-temperature L-grade selection within the precision AD544 family (vs AD544SH)
- Documented maximum offset voltage of 500 uV (vs AD547LH)
- Very low warmed-up bias current for sensitive high-impedance sources (vs AD544JH)
設計ノート
Route the amplifier input directly to the feedback network and sensitive source. The maximum input bias current of 25 pA is small, but PCB contamination and leakage can become significant on very high-impedance nodes. Use a cleaned board, remove flux residue around the input, and apply guarding where source impedances are extremely high. Keep the input trace short to minimize capacitance pickup and avoid running it beside switching-node traces.
Check the AD544 supply-voltage and common-mode limits against the actual circuit before layout release. Bypass each supply connection with a local ceramic capacitor and add bulk decoupling near the board’s supply entry point if the amplifier is separated from the capacitor by long traces. Stable power grounding is especially important in high-gain precision circuits because supply variation and ground movement can appear as input-referred error.
Do not interchange the L, J, K, and S grade suffixes without checking temperature qualification and the grade-specific electrical limits. The AD544SH extends operation from -55°C to +125°C, whereas the AD544LH is specified for 0°C to +70°C. Also confirm that any board revision uses the eight-pin TO-99 pin arrangement rather than assuming the numbering of a modern surface-mount op amp.
コンプライアンス情報
The AD544LH is a legacy hermetically sealed TO-99 amplifier. No RoHS, REACH, halogen-free, lead-free, or conflict-minerals status is stated on the product page excerpt, so those fields remain unknown. AEC-Q100 is not applicable to this non-automotive amplifier grade.