CD74AC151QM96Q1 - 8:1 Mux, AEC-Q100 | Texas Instruments
部品番号: CD74AC151QM96Q1 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $0.55 | $0.55 |
| 10 | $0.5 | $5.00 |
| 100 | $0.45 | $45.00 |
| 500 | $0.42 | $210.00 |
| 1,000 | $0.39 | $390.00 |
CD74AC151QM96Q1 概要
A digital multiplexer is a combinational logic circuit that forwards one of several input signals to a single output line, selected by binary control address inputs. In the logic IC hierarchy, the multiplexer sits under combinational logic > data routing ICs within the broader category of 4000/7400-family digital logic. Multiplexers can also act as Boolean function generators of up to four variables, parallel-to-serial converters, and data source selectors.
Key features include 8:1 selection with complementary outputs, high-speed AC-family switching comparable to bipolar F, AS, and S speed classes, operation up to 5.5 V, and balanced CMOS noise immunity. The Q1 suffix denotes AEC-Q100 qualification, making the part suitable for automotive and harsh-environment designs where temperature cycling, ESD robustness, and quality requirements exceed commercial grades.
The CD74AC151 uses advanced CMOS technology for low static power consumption combined with fast propagation delays, making it appropriate for address decoding, sensor-source selection, and data-routing in automotive ECUs, industrial control modules, and instrumentation front ends.
Typical applications include automotive body and powertrain control modules selecting among sensor channels, parallel-to-serial data conversion in microcontroller-based systems, and universal logic-function generation in FPGA glue logic and test equipment.
Design tip: tie the strobe (active-low enable) low for continuous selection, and keep unused data inputs at defined logic levels to prevent floating CMOS inputs that increase supply noise and current.
ドロップイン代替品: CD74AC151QM96Q1 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: CD74AC151QM96Q1 （同一形状・フットプリント） — 相違点: Function, Noise Immunity, Package.
クイック比較ツール — 並列比較する代替部品を選択:
CD74AC151M96
✅ ドロップイン✓ 在庫あり
$0.39 / 個
データシートを見る →CD74AC151M96
✅ ドロップイン✓ 在庫あり
$0.39 / 個
データシートを見る →CD74HC151M96
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
CD74HCT151M96
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC74HC151ADG
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
74HC151D,653
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
CD74AC151QM96Q1 最大定格＆電気的特性
| 機能 | 8-line to 1-line data selector/multiplexer |
| Number of Input Lines | 8 |
| Number of Output Lines | 2 (Y true, W complementary) |
| Family | CD74AC (Advanced CMOS) |
| Supply Voltage Range | 1.5 V to 5.5 V |
| Noise Immunity | 30% of supply voltage |
| Select Inputs | 3 (A, B, C address) |
| Enable | Active-low strobe (G') |
| Qualification | AEC-Q100 automotive grade |
| パッケージ | SOIC-16 (M) |
| 実装タイプ | Surface Mount |
| Packaging | Tape and Reel (M96 suffix) |
CD74AC151QM96Q1 ピン構成
| ピン 1 | D3 — Data input 3 |
| ピン 2 | D2 — Data input 2 |
| ピン 3 | D1 — Data input 1 |
| ピン 4 | D0 — Data input 0 |
| ピン 5 | Y — True output |
| ピン 6 | W — Complementary output |
| ピン 7 | G' — Active-low strobe/enable |
| ピン 8 | GND — Ground |
| ピン 9 | C — Select input C (MSB) |
| ピン 10 | B — Select input B |
| ピン 11 | A — Select input A (LSB) |
| ピン 12 | D7 — Data input 7 |
| ピン 13 | D6 — Data input 6 |
| ピン 14 | D5 — Data input 5 |
| ピン 15 | D4 — Data input 4 |
| ピン 16 | VCC — Power supply, 1.5 V to 5.5 V |
主な用途
CD74AC151QM96Q1 の用途: 6 件s: Automotive Sensor Source Selection, Parallel-to-Serial Data Conversion, Boolean Function Generation, Address Decoding and Data Routing, Test and Measurement Equipment, Industrial Control and Automation I/O.
Automotive Sensor Source Selection
The CD74AC151QM96Q1 selects one of eight digital sensor status or switch-bank signals in body control and powertrain modules. Its AEC-Q100 qualification addresses automotive reliability requirements, while the AC family's balanced 30%-of-VCC noise immunity maintains valid logic thresholds in electrically noisy vehicle harness environments. Placed between a switch bank and a microcontroller GPIO port, it reduces the required MCU input count from eight to four (Y output plus 3 select lines), freeing pins for other functions. The complementary W output allows redundancy checking or inverted sensing without external inverters.
おすすめ
Parallel-to-Serial Data Conversion
As noted in the TI datasheet, the CD74AC151 can perform as a parallel-to-serial converter: an 8-bit parallel word is applied to D0-D7 while a 3-bit binary counter drives the select inputs, serializing data at the Y output at the counter clock rate. The AC family's fast, uniform propagation delays keep bit-to-bit timing skew low, important for strobed acquisition systems. The strobe input gates the output during counter transitions to suppress glitches, and the W output provides the inverted serial stream for differential or redundant transmission paths in industrial acquisition front ends.
おすすめ
Boolean Function Generation
The CD74AC151 operates as a universal function generator producing any logic function of four variables, per the TI datasheet. The three select inputs A-C take the function variables, each data input is strapped to VCC or GND according to the truth table, and Y delivers the result. Compared with discrete AND/OR gate networks, a single SOIC-16 device replaces many gates, cutting BOM count and propagation delay variance. The Q1 grade allows use of this technique in automotive diagnostic and arbitration logic where fast, deterministic combinational resolution is required.
おすすめ
Address Decoding and Data Routing
In microprocessor and embedded control boards, the CD74AC151 routes one of eight register or memory-mapped status lines to a single CPU input under 3-bit address control. AC-family speed, comparable to bipolar F, AS, and S classes per the datasheet, keeps decode latency small relative to bus cycles. The active-low strobe can be driven directly by a chip-select signal so the Y output stays high (inactive) when the block is not addressed, eliminating external gating. The automotive-qualified Q1 version suits vehicle gateway and body-controller boards exposed to wide temperature ranges.
おすすめ
Test and Measurement Equipment
Bench instruments and automated test fixtures use the CD74AC151QM96Q1 to multiplex eight digital test points into one instrument channel under programmatic select control. The 1.5 V to 5.5 V operating range lets one board design serve 1.8 V, 3.3 V, and 5 V logic test targets. Balanced CMOS noise immunity of 30% of VCC keeps readings stable near switching thresholds. The strobe input blanks the output between measurement windows, preventing glitch propagation into comparators or counters during select-address changes.
おすすめ
Industrial Control and Automation I/O
PLCs and industrial I/O modules use the CD74AC151QM96Q1 to consolidate eight discrete limit-switch or relay-status inputs into a single microcontroller line. While this digital mux handles logic-level signals, pairing it with proper input conditioning (optocouplers or TVS-protected buffers) addresses industrial surge environments. The SOIC-16 footprint supports compact, reflow-soldered designs, and the complementary W output enables wired alarm logic. Select-line sequencing by the controller scans all eight channels in eight clock cycles for deterministic polling.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: CD74AC151QM96Q1 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | CD74AC151M96 | CD74HC151M96 | MC74HC151ADG |
|---|---|---|---|---|
| Package | SOIC-16 (M) | SOIC-16 (M) - same | SOIC-16 (M) - same | SOIC-16 - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Logic Family | AC (Advanced CMOS) | AC | HC | HC |
| Supply Voltage Range | 1.5 V to 5.5 V | 1.5 V to 5.5 V | 2 V to 6 V | 2 V to 6 V |
| Relative Speed | Fast (comparable to bipolar F/AS/S) | Fast (same die) | Slower | Slower |
| Outputs | Y + complementary W | Y + W | Y + W | Y + W |
主な差別化要因
- AEC-Q100 automotive qualification （vs CD74AC151M96)
- AC-family speed at wide supply range （vs CD74HC151M96)
- Complementary dual outputs （vs Single-output mux alternatives)
設計ノート
Never leave CMOS inputs floating. Tie unused data inputs D0-D7 to GND or VCC, and drive the strobe G' to a defined level even when the mux is always enabled. Floating inputs on the AC family cause intermediate conduction in the input stage, increasing supply current and noise susceptibility. Use 0.1 uF ceramic decoupling per device close to VCC pin 16 and GND pin 8.
During select-address transitions, the Y output can glitch before settling. If the output feeds a counter or clocked device, qualify it with the strobe input or add a latch (e.g., SN74HC374) clocked after select settling. The complementary W output switches simultaneously and can help with redundant or diagnostic paths. Keep select traces short and away from noisy harness routing in automotive applications.
The AC family combines CMOS static operation with fast edge rates; ground bounce increases with simultaneous output switching and low VCC operation. Use a solid ground plane, keep output load capacitance modest, and series-terminate long output traces if driving wiring harnesses. Confirm exact ICC, propagation delay, and drive current values from the TI CD74AC151 datasheet Rev. B before finalizing power and timing budgets.
コンプライアンス情報
AEC-Q100 qualification inferred from TI Q1 ordering suffix. RoHS/REACH/lead-free status must be confirmed on the TI product page for the exact ordering part number.
