DG445DY+T - Quad 85Ω SPST Analog Switch | Analog Devices
部品番号: DG445DY+T ✓ 生産中DG445DY+T 概要
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG445DY+T belongs to the CMOS analog-switch family, combining low on-resistance, normally open SPST topology, and TTL/CMOS-compatible control inputs. This places it within the broader signal-switching and interface-IC hierarchy, where accurate, low-distortion signal isolation is required in test, measurement, communication, and instrumentation systems.
Four independent switches allow one logic-control network to route four separate analog channels. Each channel provides 1:1 conduction when enabled and high impedance when disabled. The 85 Ω nominal on-resistance is suitable for many precision and medium-impedance signal paths, while matched switch behavior reduces gain variation when channels are exchanged during a measurement sequence. TTL-compatible control inputs also simplify interfacing with older digital logic families.
The redesigned DG444 and DG445 architecture improves channel-to-channel resistance matching to 4 Ω maximum and limits resistance variation over the operating signal range to 9 Ω maximum. These characteristics are particularly useful in multichannel measurement systems, where a single reference or source is routed among several inputs. Such matching helps preserve channel consistency, calibration integrity, and repeatability without requiring a separate relay for every signal path.
Typical uses include data-acquisition systems, automated test equipment, sample-and-hold circuits, signal isolation, analog test-point routing, and communication equipment. The DG445DY+T is also appropriate when one controller must select among several external inputs or distribute a source to multiple destinations. Designers should confirm the logic levels, supply rails, signal amplitude, bandwidth, and acceptable settling time for the intended application.
For layout, route each switched signal directly to its package pin and place the supply bypass capacitor close to the appropriate power pin. Avoid long traces and unnecessary stubs because parasitic capacitance can increase turn-on transients and contribute to signal distortion. The normally open architecture introduces no intentional closed-state signal path, but off-state leakage and charge injection should still be considered in high-impedance precision circuits.
This page combines the verified device identity, package and switching characteristics with practical selection guidance, application analysis, and pin-compatible family alternatives. It is intended to help engineers determine whether the DG445DY+T fits the required voltage, resistance, logic, package, and routing constraints before committing a board layout to production.
ドロップイン代替品: DG445DY+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DG445DY+T (同一形状・フットプリント) — 相違点: On-Resistance, On-Resistance Flatness, On-Resistance Matching, Operating Temperature, Package.
DG445DY+
✅ ドロップイン価格はお問い合わせください
データシートを見る →DG445DY+
✅ ドロップイン価格はお問い合わせください
データシートを見る →DG445DY-E3
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG445DY-T1
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG445DY-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG445DY+T 最大定格&電気的特性
| Number of Switch Circuits | 4 circuits |
| Configuration | 4 x SPST normally open |
| Switching Ratio | 1:1 |
| On-Resistance | 85 Ω |
| On-Resistance Matching | 4 Ω maximum between switches |
| On-Resistance Flatness | 9 Ω maximum over the signal range |
| Dual Supply Voltage Range | ±4.5 V to ±20 V |
| Control Input Compatibility | TTL and CMOS compatible |
| パッケージ | 16-pin SOIC |
| 実装タイプ | Surface mount |
| Maximum Package Length | 10 mm maximum |
| Maximum Package Height | 1.55 mm maximum |
| 動作温度 | Up to +85 °C |
DG445DY+T 1.55 mm maximum ピン配置ガイド
DG445DY+T (1.55 mm maximum パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DG445DY+T.
詳細は データシート をご参照ください。
主な用途
DG445DY+T の用途: 6 件s: Automated Test Equipment Signal Routing, Multichannel Data Acquisition, Analog Signal Isolation, Sample-and-Hold Systems, Communications Signal Routing, Programmable Instrumentation.
Automated Test Equipment Signal Routing
The DG445DY+T fits automated test equipment that must connect several analog test points without using mechanical relays. Four independent SPST channels can each place 85 Ω on-resistance between a source and a destination under digital control. The family's 4 Ω maximum matching and 9 Ω maximum flatness help maintain channel consistency when measurements are repeated across different routes. Its 16-pin SOIC package simplifies surface-mount assembly, while the normally open topology prevents unintended closed-path signal loading. Design the fixture around the ±4.5 V to ±20 V dual-supply range and verify control thresholds against the selected logic family.
おすすめ
Multichannel Data Acquisition
The DG445DY+T can route four sensed inputs into a shared acquisition or measurement channel in a data-acquisition system. Its four independent 1:1 switches provide 85 Ω on-resistance while the guaranteed 4 Ω maximum matching limits differences between switch paths. That consistency is useful when software compares channels or applies a common calibration factor. The 16-pin SOIC footprint supports compact analog boards, but designers should account for off-state leakage, charge injection, and input capacitance when using high-impedance sensors. Supply bypassing and short signal traces are especially important for preserving measurement stability.
おすすめ
Analog Signal Isolation
The DG445DY+T is useful for isolating an analog signal path from inactive branches of a test fixture or measurement system. Each normally open SPST switch presents high impedance when disabled and an 85 Ω connection when enabled, allowing one controller to determine which circuit receives the signal. The matched resistance characteristics reduce path-dependent errors when multiple nodes are scanned. Because a CMOS analog switch does not provide galvanic isolation, the device only handles electrical switching within its supply and absolute maximum limits; high-energy or hazardous signals require separate protection and isolation circuitry.
おすすめ
Sample-and-Hold Systems
The DG445DY+T can implement channel selection ahead of sample-and-hold circuitry in precision measurement designs. Routing four sources through a matched group of SPST switches helps present more consistent impedance to the following amplifier or converter. The 85 Ω on-resistance is low enough for many medium-impedance sources, while the 4 Ω maximum matching improves repeatability across the four channels. Layout quality remains critical: place bypass capacitance near the power pins, minimize switched-node capacitance, and avoid long traces that increase settling time. The dual ±4.5 V to ±20 V operating range accommodates bipolar analog nodes around ground.
おすすめ
Communications Signal Routing
The DG445DY+T can route low-frequency or moderate-bandwidth analog signals among communication-system test points and functional blocks. Its four independent channels permit fast digital selection of a receive path, test path, or impedance-matched termination. The on-resistance matching of 4 Ω maximum and flatness of 9 Ω maximum help limit gain variation as the route changes. The device is not a high-frequency RF switch, so engineers should evaluate bandwidth, capacitance, insertion loss, and isolation from the family documentation before using it in RF paths. For baseband signaling, keep routing short and establish a common ground reference across the switched nodes.
おすすめ
Programmable Instrumentation
The DG445DY+T supports programmable front ends in laboratory and field instrumentation where one controller must select among several analog inputs. Four independent SPST switches reduce the number of discrete routing components while preserving TTL/CMOS-compatible control. The 16-pin SOIC package is practical for compact instrumentation boards, and the specified resistance matching helps keep channel calibration stable. Designers should use the pin-description table to assign the four channel pairs, place the supply bypass capacitor close to the device, and maintain the control inputs at defined levels during reset. Off-state leakage and charge injection remain important in high-impedance precision measurements.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DG445DY+T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DG445DY | DG445DY | DG445DY-E3 | DG445DY-T1 | DG445DY-T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Switching Ratio | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| On-Resistance | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω |
| Control Interface | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible |
主な差別化要因
- Guaranteed channel-to-channel resistance matching (vs DG445DY-E3)
- Guaranteed on-resistance flatness over the signal range (vs DG445DY-T)
- Four-channel 85 Ω SPST switching in the standard 16-SOIC footprint (vs DG445DY-T1)
- TTL and CMOS-compatible digital control (vs MAX329CPE+)
設計ノート
Keep every switched node short and connect it directly to the corresponding SOIC pin. Long copper traces and test pads add parasitic capacitance, which can increase switching transients and settling time. Place the supply bypass capacitor close to the device power pins, use a low-inductance ground connection, and avoid routing sensitive switched signals beneath unrelated noisy circuitry. The 16-pin footprint requires careful inspection of the manufacturer pin-description table because incorrect assignment of a source, drain, control, or supply pin can prevent proper operation.
Evaluate off-state leakage, charge injection, input capacitance, and on-resistance flatness together when the source impedance is high. The 4 Ω maximum matching and 9 Ω maximum flatness are useful for reducing channel variation, but they do not remove errors caused by leakage or injected charge. Use short control traces, defined control states during reset, and an acquisition sequence that allows sufficient settling time before each measurement. For high-bandwidth signals, verify bandwidth and isolation against the manufacturer characteristics rather than relying on the DC on-resistance alone.
Use the DG445DY+T within its ±4.5 V to ±20 V dual-supply range and observe the absolute maximum ratings for both supply rails and switched signals. Bypass each supply connection close to the package with the capacitance recommended by the manufacturer. Do not allow control-input voltage to exceed the permitted logic range, and do not assume that the off state provides isolation from hazardous voltage. Additional protection is required when the switched signal can exceed the device's rating or contain significant transient energy.
Do not substitute a DG442-family device solely because it appears in a parametric-equivalent listing. The DG445 family contains four independent SPST channels, so pin count alone does not establish functional compatibility. For every proposed replacement, compare the channel count, source and drain assignments, control polarity and thresholds, supply range, electrical characteristics, package drawing, temperature rating, and lifecycle status. Treat the Vishay DG445DY-T1 listing as obsolete and do not select it for a new production design without an explicit lifecycle review.
コンプライアンス情報
A RoHS statement appears for a Vishay DG445DY-E3 listing, but it was not attributed directly to DG445DY+T. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status therefore remain unknown for the target ordering code.