DG445DY+T - Quad 85Ω SPST Analog Switch | Analog Devices
MPN: DG445DY+T ✓ Hoạt độngDG445DY+T Tóm tắt
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG445DY+T belongs to the CMOS analog-switch family, combining low on-resistance, normally open SPST topology, and TTL/CMOS-compatible control inputs. This places it within the broader signal-switching and interface-IC hierarchy, where accurate, low-distortion signal isolation is required in test, measurement, communication, and instrumentation systems.
Four independent switches allow one logic-control network to route four separate analog channels. Each channel provides 1:1 conduction when enabled and high impedance when disabled. The 85 Ω nominal on-resistance is suitable for many precision and medium-impedance signal paths, while matched switch behavior reduces gain variation when channels are exchanged during a measurement sequence. TTL-compatible control inputs also simplify interfacing with older digital logic families.
The redesigned DG444 and DG445 architecture improves channel-to-channel resistance matching to 4 Ω maximum and limits resistance variation over the operating signal range to 9 Ω maximum. These characteristics are particularly useful in multichannel measurement systems, where a single reference or source is routed among several inputs. Such matching helps preserve channel consistency, calibration integrity, and repeatability without requiring a separate relay for every signal path.
Typical uses include data-acquisition systems, automated test equipment, sample-and-hold circuits, signal isolation, analog test-point routing, and communication equipment. The DG445DY+T is also appropriate when one controller must select among several external inputs or distribute a source to multiple destinations. Designers should confirm the logic levels, supply rails, signal amplitude, bandwidth, and acceptable settling time for the intended application.
For layout, route each switched signal directly to its package pin and place the supply bypass capacitor close to the appropriate power pin. Avoid long traces and unnecessary stubs because parasitic capacitance can increase turn-on transients and contribute to signal distortion. The normally open architecture introduces no intentional closed-state signal path, but off-state leakage and charge injection should still be considered in high-impedance precision circuits.
This page combines the verified device identity, package and switching characteristics with practical selection guidance, application analysis, and pin-compatible family alternatives. It is intended to help engineers determine whether the DG445DY+T fits the required voltage, resistance, logic, package, and routing constraints before committing a board layout to production.
Bộ thay thế dễ dàng lắp đặt cho DG445DY+T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DG445DY+T (cùng hình factor và footprint) — khác nhau ở On-Resistance, On-Resistance Flatness, On-Resistance Matching, Operating Temperature, Package.
DG445DY+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG445DY+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG445DY-E3
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG445DY-T1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG445DY-T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG445DY+T Tỷ lệ tối đa & tính chất điện
| Number of Switch Circuits | 4 circuits |
| Configuration | 4 x SPST normally open |
| Switching Ratio | 1:1 |
| On-Resistance | 85 Ω |
| On-Resistance Matching | 4 Ω maximum between switches |
| On-Resistance Flatness | 9 Ω maximum over the signal range |
| Dual Supply Voltage Range | ±4.5 V to ±20 V |
| Control Input Compatibility | TTL and CMOS compatible |
| Hộp | 16-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Maximum Package Length | 10 mm maximum |
| Maximum Package Height | 1.55 mm maximum |
| Nhiệt độ hoạt động | Up to +85 °C |
Hướng dẫn cấu hình chân DG445DY+T 1.55 mm maximum
Cấu hình chân cho DG445DY+T (1.55 mm maximum gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG445DY+T.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG445DY+T phù hợp cho 6 Áp dụngs: Automated Test Equipment Signal Routing, Multichannel Data Acquisition, Analog Signal Isolation, Sample-and-Hold Systems, Communications Signal Routing, Programmable Instrumentation.
Automated Test Equipment Signal Routing
The DG445DY+T fits automated test equipment that must connect several analog test points without using mechanical relays. Four independent SPST channels can each place 85 Ω on-resistance between a source and a destination under digital control. The family's 4 Ω maximum matching and 9 Ω maximum flatness help maintain channel consistency when measurements are repeated across different routes. Its 16-pin SOIC package simplifies surface-mount assembly, while the normally open topology prevents unintended closed-path signal loading. Design the fixture around the ±4.5 V to ±20 V dual-supply range and verify control thresholds against the selected logic family.
Được đề xuất
Multichannel Data Acquisition
The DG445DY+T can route four sensed inputs into a shared acquisition or measurement channel in a data-acquisition system. Its four independent 1:1 switches provide 85 Ω on-resistance while the guaranteed 4 Ω maximum matching limits differences between switch paths. That consistency is useful when software compares channels or applies a common calibration factor. The 16-pin SOIC footprint supports compact analog boards, but designers should account for off-state leakage, charge injection, and input capacitance when using high-impedance sensors. Supply bypassing and short signal traces are especially important for preserving measurement stability.
Được đề xuất
Analog Signal Isolation
The DG445DY+T is useful for isolating an analog signal path from inactive branches of a test fixture or measurement system. Each normally open SPST switch presents high impedance when disabled and an 85 Ω connection when enabled, allowing one controller to determine which circuit receives the signal. The matched resistance characteristics reduce path-dependent errors when multiple nodes are scanned. Because a CMOS analog switch does not provide galvanic isolation, the device only handles electrical switching within its supply and absolute maximum limits; high-energy or hazardous signals require separate protection and isolation circuitry.
Được đề xuất
Sample-and-Hold Systems
The DG445DY+T can implement channel selection ahead of sample-and-hold circuitry in precision measurement designs. Routing four sources through a matched group of SPST switches helps present more consistent impedance to the following amplifier or converter. The 85 Ω on-resistance is low enough for many medium-impedance sources, while the 4 Ω maximum matching improves repeatability across the four channels. Layout quality remains critical: place bypass capacitance near the power pins, minimize switched-node capacitance, and avoid long traces that increase settling time. The dual ±4.5 V to ±20 V operating range accommodates bipolar analog nodes around ground.
Được đề xuất
Communications Signal Routing
The DG445DY+T can route low-frequency or moderate-bandwidth analog signals among communication-system test points and functional blocks. Its four independent channels permit fast digital selection of a receive path, test path, or impedance-matched termination. The on-resistance matching of 4 Ω maximum and flatness of 9 Ω maximum help limit gain variation as the route changes. The device is not a high-frequency RF switch, so engineers should evaluate bandwidth, capacitance, insertion loss, and isolation from the family documentation before using it in RF paths. For baseband signaling, keep routing short and establish a common ground reference across the switched nodes.
Được đề xuất
Programmable Instrumentation
The DG445DY+T supports programmable front ends in laboratory and field instrumentation where one controller must select among several analog inputs. Four independent SPST switches reduce the number of discrete routing components while preserving TTL/CMOS-compatible control. The 16-pin SOIC package is practical for compact instrumentation boards, and the specified resistance matching helps keep channel calibration stable. Designers should use the pin-description table to assign the four channel pairs, place the supply bypass capacitor close to the device, and maintain the control inputs at defined levels during reset. Off-state leakage and charge injection remain important in high-impedance precision measurements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG445DY+T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG445DY | DG445DY | DG445DY-E3 | DG445DY-T1 | DG445DY-T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Switching Ratio | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| On-Resistance | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω |
| Control Interface | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible |
Bảo phân biệt quan trọng
- Guaranteed channel-to-channel resistance matching (vsDG445DY-E3)
- Guaranteed on-resistance flatness over the signal range (vsDG445DY-T)
- Four-channel 85 Ω SPST switching in the standard 16-SOIC footprint (vsDG445DY-T1)
- TTL and CMOS-compatible digital control (vsMAX329CPE+)
Ghi chú thiết kế
Keep every switched node short and connect it directly to the corresponding SOIC pin. Long copper traces and test pads add parasitic capacitance, which can increase switching transients and settling time. Place the supply bypass capacitor close to the device power pins, use a low-inductance ground connection, and avoid routing sensitive switched signals beneath unrelated noisy circuitry. The 16-pin footprint requires careful inspection of the manufacturer pin-description table because incorrect assignment of a source, drain, control, or supply pin can prevent proper operation.
Evaluate off-state leakage, charge injection, input capacitance, and on-resistance flatness together when the source impedance is high. The 4 Ω maximum matching and 9 Ω maximum flatness are useful for reducing channel variation, but they do not remove errors caused by leakage or injected charge. Use short control traces, defined control states during reset, and an acquisition sequence that allows sufficient settling time before each measurement. For high-bandwidth signals, verify bandwidth and isolation against the manufacturer characteristics rather than relying on the DC on-resistance alone.
Use the DG445DY+T within its ±4.5 V to ±20 V dual-supply range and observe the absolute maximum ratings for both supply rails and switched signals. Bypass each supply connection close to the package with the capacitance recommended by the manufacturer. Do not allow control-input voltage to exceed the permitted logic range, and do not assume that the off state provides isolation from hazardous voltage. Additional protection is required when the switched signal can exceed the device's rating or contain significant transient energy.
Do not substitute a DG442-family device solely because it appears in a parametric-equivalent listing. The DG445 family contains four independent SPST channels, so pin count alone does not establish functional compatibility. For every proposed replacement, compare the channel count, source and drain assignments, control polarity and thresholds, supply range, electrical characteristics, package drawing, temperature rating, and lifecycle status. Treat the Vishay DG445DY-T1 listing as obsolete and do not select it for a new production design without an explicit lifecycle review.
Thông tin tuân thủ
A RoHS statement appears for a Vishay DG445DY-E3 listing, but it was not attributed directly to DG445DY+T. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status therefore remain unknown for the target ordering code.