DG445DY+T - Quad 85Ω SPST Analog Switch | Analog Devices
MPN: DG445DY+T ✓ فعالDG445DY+T نمای کلی
An analog switch is a semiconductor device that routes electrical signals between circuit nodes under digital control. The DG445DY+T belongs to the CMOS analog-switch family, combining low on-resistance, normally open SPST topology, and TTL/CMOS-compatible control inputs. This places it within the broader signal-switching and interface-IC hierarchy, where accurate, low-distortion signal isolation is required in test, measurement, communication, and instrumentation systems.
Four independent switches allow one logic-control network to route four separate analog channels. Each channel provides 1:1 conduction when enabled and high impedance when disabled. The 85 Ω nominal on-resistance is suitable for many precision and medium-impedance signal paths, while matched switch behavior reduces gain variation when channels are exchanged during a measurement sequence. TTL-compatible control inputs also simplify interfacing with older digital logic families.
The redesigned DG444 and DG445 architecture improves channel-to-channel resistance matching to 4 Ω maximum and limits resistance variation over the operating signal range to 9 Ω maximum. These characteristics are particularly useful in multichannel measurement systems, where a single reference or source is routed among several inputs. Such matching helps preserve channel consistency, calibration integrity, and repeatability without requiring a separate relay for every signal path.
Typical uses include data-acquisition systems, automated test equipment, sample-and-hold circuits, signal isolation, analog test-point routing, and communication equipment. The DG445DY+T is also appropriate when one controller must select among several external inputs or distribute a source to multiple destinations. Designers should confirm the logic levels, supply rails, signal amplitude, bandwidth, and acceptable settling time for the intended application.
For layout, route each switched signal directly to its package pin and place the supply bypass capacitor close to the appropriate power pin. Avoid long traces and unnecessary stubs because parasitic capacitance can increase turn-on transients and contribute to signal distortion. The normally open architecture introduces no intentional closed-state signal path, but off-state leakage and charge injection should still be considered in high-impedance precision circuits.
This page combines the verified device identity, package and switching characteristics with practical selection guidance, application analysis, and pin-compatible family alternatives. It is intended to help engineers determine whether the DG445DY+T fits the required voltage, resistance, logic, package, and routing constraints before committing a board layout to production.
جایگزینهای drop-in برای DG445DY+T — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای DG445DY+T (همان فرمفاکتور و فوتپرینت) — متفاوت در On-Resistance, On-Resistance Flatness, On-Resistance Matching, Operating Temperature, Package.
DG445DY+
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DG445DY+
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DG445DY-E3
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DG445DY-T1
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DG445DY-T
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DG445DY+T حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Switch Circuits | 4 circuits |
| Configuration | 4 x SPST normally open |
| Switching Ratio | 1:1 |
| On-Resistance | 85 Ω |
| On-Resistance Matching | 4 Ω maximum between switches |
| On-Resistance Flatness | 9 Ω maximum over the signal range |
| Dual Supply Voltage Range | ±4.5 V to ±20 V |
| Control Input Compatibility | TTL and CMOS compatible |
| بستهبندی | 16-pin SOIC |
| نوع نصب | Surface mount |
| Maximum Package Length | 10 mm maximum |
| Maximum Package Height | 1.55 mm maximum |
| دمای کاری | Up to +85 °C |
راهنمای پیکربندی پین DG445DY+T 1.55 mm maximum
پیکربندی پین برای DG445DY+T (پکیج 1.55 mm maximum). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای DG445DY+T.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
DG445DY+T مناسب است برای 6 کاربردs: Automated Test Equipment Signal Routing, Multichannel Data Acquisition, Analog Signal Isolation, Sample-and-Hold Systems, Communications Signal Routing, Programmable Instrumentation.
Automated Test Equipment Signal Routing
The DG445DY+T fits automated test equipment that must connect several analog test points without using mechanical relays. Four independent SPST channels can each place 85 Ω on-resistance between a source and a destination under digital control. The family's 4 Ω maximum matching and 9 Ω maximum flatness help maintain channel consistency when measurements are repeated across different routes. Its 16-pin SOIC package simplifies surface-mount assembly, while the normally open topology prevents unintended closed-path signal loading. Design the fixture around the ±4.5 V to ±20 V dual-supply range and verify control thresholds against the selected logic family.
پیشنهادی
Multichannel Data Acquisition
The DG445DY+T can route four sensed inputs into a shared acquisition or measurement channel in a data-acquisition system. Its four independent 1:1 switches provide 85 Ω on-resistance while the guaranteed 4 Ω maximum matching limits differences between switch paths. That consistency is useful when software compares channels or applies a common calibration factor. The 16-pin SOIC footprint supports compact analog boards, but designers should account for off-state leakage, charge injection, and input capacitance when using high-impedance sensors. Supply bypassing and short signal traces are especially important for preserving measurement stability.
پیشنهادی
Analog Signal Isolation
The DG445DY+T is useful for isolating an analog signal path from inactive branches of a test fixture or measurement system. Each normally open SPST switch presents high impedance when disabled and an 85 Ω connection when enabled, allowing one controller to determine which circuit receives the signal. The matched resistance characteristics reduce path-dependent errors when multiple nodes are scanned. Because a CMOS analog switch does not provide galvanic isolation, the device only handles electrical switching within its supply and absolute maximum limits; high-energy or hazardous signals require separate protection and isolation circuitry.
پیشنهادی
Sample-and-Hold Systems
The DG445DY+T can implement channel selection ahead of sample-and-hold circuitry in precision measurement designs. Routing four sources through a matched group of SPST switches helps present more consistent impedance to the following amplifier or converter. The 85 Ω on-resistance is low enough for many medium-impedance sources, while the 4 Ω maximum matching improves repeatability across the four channels. Layout quality remains critical: place bypass capacitance near the power pins, minimize switched-node capacitance, and avoid long traces that increase settling time. The dual ±4.5 V to ±20 V operating range accommodates bipolar analog nodes around ground.
پیشنهادی
Communications Signal Routing
The DG445DY+T can route low-frequency or moderate-bandwidth analog signals among communication-system test points and functional blocks. Its four independent channels permit fast digital selection of a receive path, test path, or impedance-matched termination. The on-resistance matching of 4 Ω maximum and flatness of 9 Ω maximum help limit gain variation as the route changes. The device is not a high-frequency RF switch, so engineers should evaluate bandwidth, capacitance, insertion loss, and isolation from the family documentation before using it in RF paths. For baseband signaling, keep routing short and establish a common ground reference across the switched nodes.
پیشنهادی
Programmable Instrumentation
The DG445DY+T supports programmable front ends in laboratory and field instrumentation where one controller must select among several analog inputs. Four independent SPST switches reduce the number of discrete routing components while preserving TTL/CMOS-compatible control. The 16-pin SOIC package is practical for compact instrumentation boards, and the specified resistance matching helps keep channel calibration stable. Designers should use the pin-description table to assign the four channel pairs, place the supply bypass capacitor close to the device, and maintain the control inputs at defined levels during reset. Off-state leakage and charge injection remain important in high-impedance precision measurements.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای DG445DY+T — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | DG445DY | DG445DY | DG445DY-E3 | DG445DY-T1 | DG445DY-T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Switching Ratio | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 | 1:1 |
| On-Resistance | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω | 85 Ω |
| Control Interface | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible |
تفاوتهای کلیدی
- Guaranteed channel-to-channel resistance matching (در مقابلDG445DY-E3)
- Guaranteed on-resistance flatness over the signal range (در مقابلDG445DY-T)
- Four-channel 85 Ω SPST switching in the standard 16-SOIC footprint (در مقابلDG445DY-T1)
- TTL and CMOS-compatible digital control (در مقابلMAX329CPE+)
یادداشتهای طراحی
Keep every switched node short and connect it directly to the corresponding SOIC pin. Long copper traces and test pads add parasitic capacitance, which can increase switching transients and settling time. Place the supply bypass capacitor close to the device power pins, use a low-inductance ground connection, and avoid routing sensitive switched signals beneath unrelated noisy circuitry. The 16-pin footprint requires careful inspection of the manufacturer pin-description table because incorrect assignment of a source, drain, control, or supply pin can prevent proper operation.
Evaluate off-state leakage, charge injection, input capacitance, and on-resistance flatness together when the source impedance is high. The 4 Ω maximum matching and 9 Ω maximum flatness are useful for reducing channel variation, but they do not remove errors caused by leakage or injected charge. Use short control traces, defined control states during reset, and an acquisition sequence that allows sufficient settling time before each measurement. For high-bandwidth signals, verify bandwidth and isolation against the manufacturer characteristics rather than relying on the DC on-resistance alone.
Use the DG445DY+T within its ±4.5 V to ±20 V dual-supply range and observe the absolute maximum ratings for both supply rails and switched signals. Bypass each supply connection close to the package with the capacitance recommended by the manufacturer. Do not allow control-input voltage to exceed the permitted logic range, and do not assume that the off state provides isolation from hazardous voltage. Additional protection is required when the switched signal can exceed the device's rating or contain significant transient energy.
Do not substitute a DG442-family device solely because it appears in a parametric-equivalent listing. The DG445 family contains four independent SPST channels, so pin count alone does not establish functional compatibility. For every proposed replacement, compare the channel count, source and drain assignments, control polarity and thresholds, supply range, electrical characteristics, package drawing, temperature rating, and lifecycle status. Treat the Vishay DG445DY-T1 listing as obsolete and do not select it for a new production design without an explicit lifecycle review.
اطلاعات انطباق
A RoHS statement appears for a Vishay DG445DY-E3 listing, but it was not attributed directly to DG445DY+T. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status therefore remain unknown for the target ordering code.