DS90CR217MTD - 3.3V LVDS 21-Bit Transmitter | Texas Instruments
部品番号: DS90CR217MTD ✗ 生産終了DS90CR217MTD 概要
An LVDS transmitter is a differential signaling interface IC that converts low-voltage CMOS/TTL logic into low-voltage differential signals. This technique reduces signal amplitude while improving noise immunity and allowing reliable transmission across cable or PCB connections. The DS90CR217MTD belongs to the LVDS interface IC hierarchy, alongside differential line drivers, receivers, serializers, and Channel Link devices.
The primary electrical features include a 3.3 V supply, 21-bit parallel data input, three LVDS outputs, and an 85 MHz maximum rising-edge data-strobe frequency. The 48-pin TSSOP package supports compact board layouts, while the differential outputs are intended for controlled-impedance routing. The transmitter architecture is particularly useful when a system needs to move parallel digital data across a board-to-board cable, backplane, or external module.
Typical applications include video and display interfaces, industrial visualization systems, test equipment, imaging systems, and communications equipment. When selecting this transmitter, verify the receiver's clocking convention, lane mapping, termination arrangement, cable length, and LVDS voltage levels before releasing a PCB layout. The manufacturer datasheet should be used for the complete pin list, electrical limits, timing values, and recommended termination network.
ドロップイン代替品: DS90CR217MTD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90CR217MTD (同一形状・フットプリント) — 相違点: Package, Product Type, Input Logic, Maximum Clock Frequency, Output Logic.
DS90CR217MTD/NOPB
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90CR217MTD
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90CR216AMTD
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90C363MTD
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90C385AMTX
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90CR217MTD 仕様
| Product Type | LVDS Channel Link transmitter |
| 電源電圧 | 3.3 V |
| Input Data Width | 21 bits |
| 最大クロック周波数 | 85 MHz |
| Data Transfer Rate | 1.785 Gbps |
| Data Output | 3 LVDS data streams plus LVDS clock |
| Input Logic | CMOS/TTL |
| Output Logic | LVDS differential signaling |
| Clocking Edge | Rising edge |
| パッケージ | 48-pin TSSOP |
| Package Family | TSSOP-48 |
| 実装タイプ | Surface mount |
DS90CR217MTD tssop-48 ピン配置ガイド
DS90CR217MTD (tssop-48 パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90CR217MTD.
詳細は データシート をご参照ください。
主な用途
DS90CR217MTD の用途: 6 件s: Display and Video Data Links, Industrial Visualization Systems, Imaging and Test Equipment, Board-to-Board Communications, Communications and Data Modules, Camera and Security Modules.
Display and Video Data Links
The DS90CR217MTD fits parallel-to-LVDS links used between a video controller and an external display or processing module. Its 21-bit input width, 3.3 V operation, rising-edge clocking, and 85 MHz maximum clock frequency support high-speed digital transport over a cable or controlled-impedance board connection. The three LVDS data outputs provide a compact serialized interface while preserving parallel-source simplicity. Designers should confirm receiver lane mapping, blanking or control-signal handling, cable length, and termination before layout.
おすすめ
Industrial Visualization Systems
A DS90CR217MTD can serialize a 21-bit parallel data bus for industrial visualization equipment, inspection systems, and machine-control panels. The 48-TSSOP package supports compact controller boards, while the 1.785 Gbps stated aggregate rate provides margin for multi-lane LVDS transport. The transmitter is appropriate when the receiving equipment supports the same Channel Link format and clock edge. Industrial designs should also plan for grounding, ESD protection, cable shielding, and production testing of differential outputs.
おすすめ
Imaging and Test Equipment
The DS90CR217MTD is suitable for transmitting parallel digital data from imaging, acquisition, and test modules to a remote processor. A 21-bit payload can carry pixel or acquisition data while the separate LVDS clock supports source-synchronous timing. The 85 MHz operating ceiling and low-amplitude differential signaling help preserve data integrity across longer interconnects than a single-ended bus. Verify connector pin assignments, receiver termination, skew requirements, and isolation strategy for each cable or harness.
おすすめ
Board-to-Board Communications
Use the DS90CR217MTD when a PCB must transfer a wide parallel bus to another board over a short high-speed LVDS connection. The 21-bit input reduces the number of traces crossing the interconnect, and the three differential outputs support a scalable Channel Link connection. Its TSSOP-48 package is suitable for standard surface-mount assembly, although controlled-impedance layout and careful return-path planning remain essential. Compare the source and destination clocking, data mapping, and termination before approving the interface.
おすすめ
Communications and Data Modules
The DS90CR217MTD can bridge parallel logic inside a communications module to an external LVDS link. Its 3.3 V operation is compatible with modern low-voltage digital systems, and the transmitter provides a defined path for carrying a 21-bit payload plus clock across a cable or backplane. Because channel-link transceivers are system-specific, the receiving device, protocol framing, and clock recovery method must match. Validate signal integrity with the actual connector and cable configuration.
おすすめ
Camera and Security Modules
The DS90CR217MTD can be used in camera and security-system modules that need to move parallel image or control data to a remote processor. Differential LVDS signaling is useful for reducing EMI sensitivity and improving robustness over interconnects. The transmitter's 21-bit width and 85 MHz clocking provide a clear interface budget for multi-lane serialized data, but the receiver must support the same data format and lane ordering. Pay attention to cable length, connector return pins, and grounding when integrating the module.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90CR217MTD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90CR217MTD/NOPB | DS90CR216AMTD | DS90C363MTD | DS90C385AMTX |
|---|---|---|---|---|---|
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主な差別化要因
- Directly identified alternate ordering designation (vs DS90CR217MTD/NOPB)
- High-bandwidth parallel-to-LVDS conversion (vs DS90CR216AMTD)
- Established DS90 family interface ecosystem (vs DS90C363MTD)
設計ノート
Route each LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous reference plane. Avoid stubs, test pads, and unnecessary layer transitions on the data and clock pairs. Keep the transmitter, receiver, and termination arrangement consistent with the manufacturer's recommended Channel Link implementation.
Do not assume that all DS90 family devices are interchangeable simply because they use a 48-TSSOP package. Confirm the input width, clock edge, output lane count, LVDS levels, timing, and pin mapping against the original DS90CR217MTD datasheet. The 48-TSSOP footprint alone does not establish electrical or timing compatibility.
Use the receiver's required termination network and maintain a low-impedance ground return between the transmitter and receiver. Place bypass capacitors close to the supply and ground pins, and inspect the differential-to-common-mode balance at the connector and cable. These practices reduce susceptibility to noise and improve repeatability across cable lengths.
コンプライアンス情報
Compliance status requires confirmation from the manufacturer datasheet or product documentation.