DS90CR217MTD - 3.3V LVDS 21-Bit Transmitter | Texas Instruments
N.º da peça: DS90CR217MTD ✗ Fim de vidaDS90CR217MTD Visão geral
An LVDS transmitter is a differential signaling interface IC that converts low-voltage CMOS/TTL logic into low-voltage differential signals. This technique reduces signal amplitude while improving noise immunity and allowing reliable transmission across cable or PCB connections. The DS90CR217MTD belongs to the LVDS interface IC hierarchy, alongside differential line drivers, receivers, serializers, and Channel Link devices.
The primary electrical features include a 3.3 V supply, 21-bit parallel data input, three LVDS outputs, and an 85 MHz maximum rising-edge data-strobe frequency. The 48-pin TSSOP package supports compact board layouts, while the differential outputs are intended for controlled-impedance routing. The transmitter architecture is particularly useful when a system needs to move parallel digital data across a board-to-board cable, backplane, or external module.
Typical applications include video and display interfaces, industrial visualization systems, test equipment, imaging systems, and communications equipment. When selecting this transmitter, verify the receiver's clocking convention, lane mapping, termination arrangement, cable length, and LVDS voltage levels before releasing a PCB layout. The manufacturer datasheet should be used for the complete pin list, electrical limits, timing values, and recommended termination network.
Alternativas drop-in para DS90CR217MTD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com DS90CR217MTD (mesmo formato e footprint) — diferindo em Package, Product Type, Input Logic, Maximum Clock Frequency, Output Logic.
DS90CR217MTD/NOPB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
DS90CR217MTD
✅ Drop-InConsulte o preço
Ver ficha técnica →DS90CR216AMTD
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
DS90C363MTD
✅ Drop-InConsulte o preço
Ver ficha técnica →DS90C385AMTX
✅ Drop-InConsulte o preço
Ver ficha técnica →DS90CR217MTD Especificações
| Product Type | LVDS Channel Link transmitter |
| Tensão de alimentação | 3.3 V |
| Input Data Width | 21 bits |
| Frequência máxima de clock | 85 MHz |
| Data Transfer Rate | 1.785 Gbps |
| Data Output | 3 LVDS data streams plus LVDS clock |
| Input Logic | CMOS/TTL |
| Output Logic | LVDS differential signaling |
| Clocking Edge | Rising edge |
| Encapsulamento | 48-pin TSSOP |
| Package Family | TSSOP-48 |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do DS90CR217MTD tssop-48
Configuração de pinos para DS90CR217MTD (pacote tssop-48). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para DS90CR217MTD.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
DS90CR217MTD é adequado para 6 aplicaçãos: Display and Video Data Links, Industrial Visualization Systems, Imaging and Test Equipment, Board-to-Board Communications, Communications and Data Modules, Camera and Security Modules.
Display and Video Data Links
The DS90CR217MTD fits parallel-to-LVDS links used between a video controller and an external display or processing module. Its 21-bit input width, 3.3 V operation, rising-edge clocking, and 85 MHz maximum clock frequency support high-speed digital transport over a cable or controlled-impedance board connection. The three LVDS data outputs provide a compact serialized interface while preserving parallel-source simplicity. Designers should confirm receiver lane mapping, blanking or control-signal handling, cable length, and termination before layout.
Recomendado
Industrial Visualization Systems
A DS90CR217MTD can serialize a 21-bit parallel data bus for industrial visualization equipment, inspection systems, and machine-control panels. The 48-TSSOP package supports compact controller boards, while the 1.785 Gbps stated aggregate rate provides margin for multi-lane LVDS transport. The transmitter is appropriate when the receiving equipment supports the same Channel Link format and clock edge. Industrial designs should also plan for grounding, ESD protection, cable shielding, and production testing of differential outputs.
Recomendado
Imaging and Test Equipment
The DS90CR217MTD is suitable for transmitting parallel digital data from imaging, acquisition, and test modules to a remote processor. A 21-bit payload can carry pixel or acquisition data while the separate LVDS clock supports source-synchronous timing. The 85 MHz operating ceiling and low-amplitude differential signaling help preserve data integrity across longer interconnects than a single-ended bus. Verify connector pin assignments, receiver termination, skew requirements, and isolation strategy for each cable or harness.
Recomendado
Board-to-Board Communications
Use the DS90CR217MTD when a PCB must transfer a wide parallel bus to another board over a short high-speed LVDS connection. The 21-bit input reduces the number of traces crossing the interconnect, and the three differential outputs support a scalable Channel Link connection. Its TSSOP-48 package is suitable for standard surface-mount assembly, although controlled-impedance layout and careful return-path planning remain essential. Compare the source and destination clocking, data mapping, and termination before approving the interface.
Recomendado
Communications and Data Modules
The DS90CR217MTD can bridge parallel logic inside a communications module to an external LVDS link. Its 3.3 V operation is compatible with modern low-voltage digital systems, and the transmitter provides a defined path for carrying a 21-bit payload plus clock across a cable or backplane. Because channel-link transceivers are system-specific, the receiving device, protocol framing, and clock recovery method must match. Validate signal integrity with the actual connector and cable configuration.
Recomendado
Camera and Security Modules
The DS90CR217MTD can be used in camera and security-system modules that need to move parallel image or control data to a remote processor. Differential LVDS signaling is useful for reducing EMI sensitivity and improving robustness over interconnects. The transmitter's 21-bit width and 85 MHz clocking provide a clear interface budget for multi-lane serialized data, but the receiver must support the same data format and lane ordering. Pay attention to cable length, connector return pins, and grounding when integrating the module.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para DS90CR217MTD — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | DS90CR217MTD/NOPB | DS90CR216AMTD | DS90C363MTD | DS90C385AMTX |
|---|---|---|---|---|---|
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Principais diferenciais
- Directly identified alternate ordering designation (vs DS90CR217MTD/NOPB)
- High-bandwidth parallel-to-LVDS conversion (vs DS90CR216AMTD)
- Established DS90 family interface ecosystem (vs DS90C363MTD)
Notas de projeto
Route each LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous reference plane. Avoid stubs, test pads, and unnecessary layer transitions on the data and clock pairs. Keep the transmitter, receiver, and termination arrangement consistent with the manufacturer's recommended Channel Link implementation.
Do not assume that all DS90 family devices are interchangeable simply because they use a 48-TSSOP package. Confirm the input width, clock edge, output lane count, LVDS levels, timing, and pin mapping against the original DS90CR217MTD datasheet. The 48-TSSOP footprint alone does not establish electrical or timing compatibility.
Use the receiver's required termination network and maintain a low-impedance ground return between the transmitter and receiver. Place bypass capacitors close to the supply and ground pins, and inspect the differential-to-common-mode balance at the connector and cable. These practices reduce susceptibility to noise and improve repeatability across cable lengths.
Informações de conformidade
Compliance status requires confirmation from the manufacturer datasheet or product documentation.