DS90CR217MTD - 3.3V LVDS 21-Bit Transmitter | Texas Instruments
MPN: DS90CR217MTD ✗ 停產DS90CR217MTD 概覽
An LVDS transmitter is a differential signaling interface IC that converts low-voltage CMOS/TTL logic into low-voltage differential signals. This technique reduces signal amplitude while improving noise immunity and allowing reliable transmission across cable or PCB connections. The DS90CR217MTD belongs to the LVDS interface IC hierarchy, alongside differential line drivers, receivers, serializers, and Channel Link devices.
The primary electrical features include a 3.3 V supply, 21-bit parallel data input, three LVDS outputs, and an 85 MHz maximum rising-edge data-strobe frequency. The 48-pin TSSOP package supports compact board layouts, while the differential outputs are intended for controlled-impedance routing. The transmitter architecture is particularly useful when a system needs to move parallel digital data across a board-to-board cable, backplane, or external module.
Typical applications include video and display interfaces, industrial visualization systems, test equipment, imaging systems, and communications equipment. When selecting this transmitter, verify the receiver's clocking convention, lane mapping, termination arrangement, cable length, and LVDS voltage levels before releasing a PCB layout. The manufacturer datasheet should be used for the complete pin list, electrical limits, timing values, and recommended termination network.
直接替換替代品,適用於 DS90CR217MTD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: DS90CR217MTD (相同外形與佔位) — 差異在於 Package, Product Type, Input Logic, Maximum Clock Frequency, Output Logic.
DS90CR217MTD/NOPB
✅ 直接替換📋 參考替代品(不在目錄中)
DS90CR217MTD
✅ 直接替換聯絡詢價
查看資料表 →DS90CR216AMTD
✅ 直接替換📋 參考替代品(不在目錄中)
DS90C363MTD
✅ 直接替換聯絡詢價
查看資料表 →DS90C385AMTX
✅ 直接替換聯絡詢價
查看資料表 →DS90CR217MTD 規格
| Product Type | LVDS Channel Link transmitter |
| 供應電壓 | 3.3 V |
| Input Data Width | 21 bits |
| 最大時脈頻率 | 85 MHz |
| Data Transfer Rate | 1.785 Gbps |
| Data Output | 3 LVDS data streams plus LVDS clock |
| Input Logic | CMOS/TTL |
| Output Logic | LVDS differential signaling |
| Clocking Edge | Rising edge |
| 封裝 | 48-pin TSSOP |
| Package Family | TSSOP-48 |
| 安裝類型 | Surface mount |
DS90CR217MTD tssop-48 腳位配置指南
DS90CR217MTD(tssop-48 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DS90CR217MTD.
請參閱 資料表 以查看完整腳位配置。
典型應用
DS90CR217MTD 適用於 6 應用s: Display and Video Data Links, Industrial Visualization Systems, Imaging and Test Equipment, Board-to-Board Communications, Communications and Data Modules, Camera and Security Modules.
Display and Video Data Links
The DS90CR217MTD fits parallel-to-LVDS links used between a video controller and an external display or processing module. Its 21-bit input width, 3.3 V operation, rising-edge clocking, and 85 MHz maximum clock frequency support high-speed digital transport over a cable or controlled-impedance board connection. The three LVDS data outputs provide a compact serialized interface while preserving parallel-source simplicity. Designers should confirm receiver lane mapping, blanking or control-signal handling, cable length, and termination before layout.
推薦
Industrial Visualization Systems
A DS90CR217MTD can serialize a 21-bit parallel data bus for industrial visualization equipment, inspection systems, and machine-control panels. The 48-TSSOP package supports compact controller boards, while the 1.785 Gbps stated aggregate rate provides margin for multi-lane LVDS transport. The transmitter is appropriate when the receiving equipment supports the same Channel Link format and clock edge. Industrial designs should also plan for grounding, ESD protection, cable shielding, and production testing of differential outputs.
推薦
Imaging and Test Equipment
The DS90CR217MTD is suitable for transmitting parallel digital data from imaging, acquisition, and test modules to a remote processor. A 21-bit payload can carry pixel or acquisition data while the separate LVDS clock supports source-synchronous timing. The 85 MHz operating ceiling and low-amplitude differential signaling help preserve data integrity across longer interconnects than a single-ended bus. Verify connector pin assignments, receiver termination, skew requirements, and isolation strategy for each cable or harness.
推薦
Board-to-Board Communications
Use the DS90CR217MTD when a PCB must transfer a wide parallel bus to another board over a short high-speed LVDS connection. The 21-bit input reduces the number of traces crossing the interconnect, and the three differential outputs support a scalable Channel Link connection. Its TSSOP-48 package is suitable for standard surface-mount assembly, although controlled-impedance layout and careful return-path planning remain essential. Compare the source and destination clocking, data mapping, and termination before approving the interface.
推薦
Communications and Data Modules
The DS90CR217MTD can bridge parallel logic inside a communications module to an external LVDS link. Its 3.3 V operation is compatible with modern low-voltage digital systems, and the transmitter provides a defined path for carrying a 21-bit payload plus clock across a cable or backplane. Because channel-link transceivers are system-specific, the receiving device, protocol framing, and clock recovery method must match. Validate signal integrity with the actual connector and cable configuration.
推薦
Camera and Security Modules
The DS90CR217MTD can be used in camera and security-system modules that need to move parallel image or control data to a remote processor. Differential LVDS signaling is useful for reducing EMI sensitivity and improving robustness over interconnects. The transmitter's 21-bit width and 85 MHz clocking provide a clear interface budget for multi-lane serialized data, but the receiver must support the same data format and lane ordering. Pay attention to cable length, connector return pins, and grounding when integrating the module.
推薦
工程參考資料,適用於 DS90CR217MTD — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DS90CR217MTD/NOPB | DS90CR216AMTD | DS90C363MTD | DS90C385AMTX |
|---|---|---|---|---|---|
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主要差異化特點
- Directly identified alternate ordering designation (對比DS90CR217MTD/NOPB)
- High-bandwidth parallel-to-LVDS conversion (對比DS90CR216AMTD)
- Established DS90 family interface ecosystem (對比DS90C363MTD)
設計說明
Route each LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous reference plane. Avoid stubs, test pads, and unnecessary layer transitions on the data and clock pairs. Keep the transmitter, receiver, and termination arrangement consistent with the manufacturer's recommended Channel Link implementation.
Do not assume that all DS90 family devices are interchangeable simply because they use a 48-TSSOP package. Confirm the input width, clock edge, output lane count, LVDS levels, timing, and pin mapping against the original DS90CR217MTD datasheet. The 48-TSSOP footprint alone does not establish electrical or timing compatibility.
Use the receiver's required termination network and maintain a low-impedance ground return between the transmitter and receiver. Place bypass capacitors close to the supply and ground pins, and inspect the differential-to-common-mode balance at the connector and cable. These practices reduce susceptibility to noise and improve repeatability across cable lengths.
合規資訊
Compliance status requires confirmation from the manufacturer datasheet or product documentation.