Texas Instruments

DS90CR217MTD - 3.3V LVDS 21-Bit Transmitter | Texas Instruments

MPN: DS90CR217MTD ✗ Akhir Hayat
3.3 V Vdss 48-pin TSSOP Package 85 MHz Speed
MOQ: 1 |

DS90CR217MTD Ringkasan

Texas Instruments DS90CR217MTD is a 3.3 V rising-edge data-strobe LVDS transmitter designed for high-speed digital point-to-point links. The device accepts 21 parallel CMOS/TTL data bits and a clock, then serializes the payload into three differential LVDS data streams plus a separate LVDS clock output. Its 85 MHz rising-edge Channel Link interface supports transfer rates of 1.785 Gbps and is designed for use in display, video, communications, and industrial control systems.

An LVDS transmitter is a differential signaling interface IC that converts low-voltage CMOS/TTL logic into low-voltage differential signals. This technique reduces signal amplitude while improving noise immunity and allowing reliable transmission across cable or PCB connections. The DS90CR217MTD belongs to the LVDS interface IC hierarchy, alongside differential line drivers, receivers, serializers, and Channel Link devices.

The primary electrical features include a 3.3 V supply, 21-bit parallel data input, three LVDS outputs, and an 85 MHz maximum rising-edge data-strobe frequency. The 48-pin TSSOP package supports compact board layouts, while the differential outputs are intended for controlled-impedance routing. The transmitter architecture is particularly useful when a system needs to move parallel digital data across a board-to-board cable, backplane, or external module.

Typical applications include video and display interfaces, industrial visualization systems, test equipment, imaging systems, and communications equipment. When selecting this transmitter, verify the receiver's clocking convention, lane mapping, termination arrangement, cable length, and LVDS voltage levels before releasing a PCB layout. The manufacturer datasheet should be used for the complete pin list, electrical limits, timing values, and recommended termination network.

Pilihan pengganti yang segera untuk DS90CR217MTD — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera DS90CR217MTD (sama faktor bentuk dan kaki) — berbeza dalam Package, Product Type, Input Logic, Maximum Clock Frequency, Output Logic.

Texas Instruments
Package: 48-TSSOP, 0.240 inch (6.10 mm) width
Product Type: Programmable LVDS FPD-Link transmitter
Maximum Clock Frequency: 65 MHz
Bandingkan Dengan DS90CR217MTD →
Texas Instruments
Package: 56-pin TSSOP
Product Type: Programmable LVDS flat-panel-display transmitter
Input Logic: LVCMOS/LVTTL
Bandingkan Dengan DS90CR217MTD →

DS90CR217MTD/NOPB

✅ Masuk Drop-In
📦 48-TSSOP
Same DS90CR217 family, 48-TSSOP package, 3.3 V supply, and 21-bit 85 MHz LVDS transmitter function; ordering suffix differs

📋 Alternatif rujukan (tidak dalam katalog)

DS90CR217MTD

✅ Masuk Drop-In
Texas Instruments
📦 48-TSSOP
LVDS Channel Link transmitter · 3.3 V · 21 bits · 85 MHz · 1.785 Gbps · 3 LVDS data streams plus LVDS clock · CMOS/TTL · LVDS differential signaling

Hubungi untuk harga

Lihat Datasheet →

DS90CR216AMTD

✅ Masuk Drop-In
📦 48-TSSOP
Related 48-TSSOP LVDS Channel Link transmitter family; data width, clocking, and timing must be matched before use

📋 Alternatif rujukan (tidak dalam katalog)

DS90C363MTD

✅ Masuk Drop-In
Texas Instruments
📦 48-TSSOP
Programmable LVDS FPD-Link transmitter · 3 V to 3.6 V · 3.3 V · 18 bits · 65 MHz · 1300 Mbps · 0.45 V · 3 drivers

Hubungi untuk harga

Lihat Datasheet →

DS90C385AMTX

✅ Masuk Drop-In
Texas Instruments
📦 48-TSSOP
Programmable LVDS flat-panel-display transmitter · 3.3 V · 87.5 MHz · 85 MHz · 28 bits · 24 bits · 3 bits · 4 differential streams

Hubungi untuk harga

Lihat Datasheet →

DS90CR217MTD Spesifikasi

Product Type LVDS Channel Link transmitter
Tegangan Pemberi Arus 3.3 V
Input Data Width 21 bits
Frekuensi Klock Maksimum 85 MHz
Data Transfer Rate 1.785 Gbps
Data Output 3 LVDS data streams plus LVDS clock
Input Logic CMOS/TTL
Output Logic LVDS differential signaling
Clocking Edge Rising edge
Kemasan 48-pin TSSOP
Package Family TSSOP-48
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin DS90CR217MTD tssop-48

Konfigurasi pin untuk DS90CR217MTD (tssop-48 pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai tssop-48 untuk DS90CR217MTD

Tiada data garisan pin yang diperoleh untuk DS90CR217MTD.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

DS90CR217MTD patut untuk 6 aplikasis: Display and Video Data Links, Industrial Visualization Systems, Imaging and Test Equipment, Board-to-Board Communications, Communications and Data Modules, Camera and Security Modules.

📺

Display and Video Data Links

The DS90CR217MTD fits parallel-to-LVDS links used between a video controller and an external display or processing module. Its 21-bit input width, 3.3 V operation, rising-edge clocking, and 85 MHz maximum clock frequency support high-speed digital transport over a cable or controlled-impedance board connection. The three LVDS data outputs provide a compact serialized interface while preserving parallel-source simplicity. Designers should confirm receiver lane mapping, blanking or control-signal handling, cable length, and termination before layout.

🏭

Industrial Visualization Systems

A DS90CR217MTD can serialize a 21-bit parallel data bus for industrial visualization equipment, inspection systems, and machine-control panels. The 48-TSSOP package supports compact controller boards, while the 1.785 Gbps stated aggregate rate provides margin for multi-lane LVDS transport. The transmitter is appropriate when the receiving equipment supports the same Channel Link format and clock edge. Industrial designs should also plan for grounding, ESD protection, cable shielding, and production testing of differential outputs.

🖥️

Imaging and Test Equipment

The DS90CR217MTD is suitable for transmitting parallel digital data from imaging, acquisition, and test modules to a remote processor. A 21-bit payload can carry pixel or acquisition data while the separate LVDS clock supports source-synchronous timing. The 85 MHz operating ceiling and low-amplitude differential signaling help preserve data integrity across longer interconnects than a single-ended bus. Verify connector pin assignments, receiver termination, skew requirements, and isolation strategy for each cable or harness.

🔧

Board-to-Board Communications

Use the DS90CR217MTD when a PCB must transfer a wide parallel bus to another board over a short high-speed LVDS connection. The 21-bit input reduces the number of traces crossing the interconnect, and the three differential outputs support a scalable Channel Link connection. Its TSSOP-48 package is suitable for standard surface-mount assembly, although controlled-impedance layout and careful return-path planning remain essential. Compare the source and destination clocking, data mapping, and termination before approving the interface.

🌐

Communications and Data Modules

The DS90CR217MTD can bridge parallel logic inside a communications module to an external LVDS link. Its 3.3 V operation is compatible with modern low-voltage digital systems, and the transmitter provides a defined path for carrying a 21-bit payload plus clock across a cable or backplane. Because channel-link transceivers are system-specific, the receiving device, protocol framing, and clock recovery method must match. Validate signal integrity with the actual connector and cable configuration.

🎥

Camera and Security Modules

The DS90CR217MTD can be used in camera and security-system modules that need to move parallel image or control data to a remote processor. Differential LVDS signaling is useful for reducing EMI sensitivity and improving robustness over interconnects. The transmitter's 21-bit width and 85 MHz clocking provide a clear interface budget for multi-lane serialized data, but the receiver must support the same data format and lane ordering. Pay attention to cable length, connector return pins, and grounding when integrating the module.

What is the DS90CR217MTD?
The DS90CR217MTD is a 3.3 V rising-edge LVDS Channel Link transmitter from Texas Instruments. It converts 21 parallel CMOS/TTL data bits and a clock into three differential LVDS data streams and a clock output. According to the manufacturer product page, the device is intended for 85 MHz operation and high-speed point-to-point digital links.
What is the operating voltage of DS90CR217MTD?
The DS90CR217MTD operates from a 3.3 V supply. The verified manufacturer product description identifies the device as a +3.3 V rising-edge data-strobe LVDS transmitter. Its power rails, input thresholds, output levels, and absolute maximum ratings should be confirmed in the manufacturer datasheet before designing the interface.
What is the maximum data rate of DS90CR217MTD?
The DS90CR217MTD supports a maximum rising-edge clock frequency of 85 MHz, corresponding to a stated 1.785 Gbps aggregate data rate. The manufacturer product page identifies the device as a 21-bit Channel Link transmitter with 85 MHz operation. The exact per-lane and aggregate payload interpretation should follow the datasheet timing definitions.
Where can I download the DS90CR217MTD datasheet PDF?
The official Texas Instruments product page for the DS90CR217 is the best starting point for the datasheet and supporting documentation. The verified search results also identify a DS90CR217MTD datasheet page on AllDataSheet and a Datasheets.com part page. Use the manufacturer datasheet for final pin, timing, and electrical-limit decisions.
Where can I find the DS90CR217MTD pinout?
The DS90CR217MTD pinout is defined in the manufacturer datasheet and must be used for PCB routing because the device is a 48-pin TSSOP package. The complete pin names, power pins, ground pins, clock inputs, data inputs, and LVDS outputs should be transcribed from the datasheet pin-description table rather than inferred from the distributor listing.
Is DS90CR217MTD suitable for a video link?
The DS90CR217MTD can be suitable for a video or display link when the system matches its 21-bit parallel input architecture, rising-edge clocking, 85 MHz maximum frequency, and LVDS electrical requirements. The transmitter is designed for high-speed point-to-point connections, but cable length, receiver compatibility, lane mapping, and termination must be verified before implementation.
What is the difference between DS90CR217MTD and DS90CR217MTD/NOPB?
DS90CR217MTD is the manufacturer ordering designation, while DS90CR217MTD/NOPB identifies the lead-free, standard-brightness or orderable variant used by distributors. The verified listing describes DS90CR217MTD/NOPB as the 48-TSSOP version of the same DS90CR217 family. Confirm the orderable suffix, terminal finish, and lifecycle markings on the manufacturer product page before substitution.
Can DS90CR217MTD be replaced by a drop-in alternative?
A drop-in replacement should use the same 48-TSSOP footprint, compatible LVDS output arrangement, 3.3 V supply, 21-bit input interface, and compatible rising-edge timing. The verified cross-reference results identify DS90CR217MTD/NOPB as the closest ordering variant, while other listed devices are not confirmed as pin-compatible replacements. Validate any substitute against the original datasheet.
When should I choose DS90CR217MTD over another LVDS transmitter?
Choose the DS90CR217MTD when the system needs a 21-bit parallel-to-LVDS conversion with a rising-edge clock, 3.3 V operation, and up to 85 MHz clocking. It is a strong fit for cable links and board-to-board connections where the receiver already supports the corresponding Channel Link data and clock arrangement. It is less suitable when a different bit width, edge polarity, or lane count is required.
Is DS90CR217MTD in stock?
Stock status should be checked through the Request a Quote form on this page. The verified distributor result for DS90CR217MTD identifies the part as NRND and points to DS90CR217MTD/NOPB as an alternate ordering designation. For production planning, request the current inventory, lead time, minimum order quantity, and confirmed lifecycle status before committing a design.
What is the price of DS90CR217MTD?
Use the Request a Quote form on this page for the current DS90CR217MTD commercial offer. The verified distributor listings provide product and ordering information, but they do not provide a qualifying printed quantity-break price table for this exact MPN. Pricing and availability should therefore be confirmed directly through the quote process.
Where can I buy DS90CR217MTD online?
The DS90CR217MTD can be requested through the Request a Quote form on this page. The verified listings identify Texas Instruments as the manufacturer and include DS90CR217MTD and DS90CR217MTD/NOPB ordering references. Request the exact suffix, package, quantity, and delivery requirements to avoid mismatched inventory.
What is the lead time for DS90CR217MTD?
The current lead time for DS90CR217MTD should be requested through the Request a Quote form on this page. Because the part is identified as NRND in the verified distributor listing, production planning should include a written availability confirmation. Lead time, allocation, and obsolete-material handling may depend on the requested quantity and package suffix.
What are the key specifications of DS90CR217MTD that engineers should know?
The key engineering specifications for DS90CR217MTD are a 3.3 V supply, 21-bit parallel input, 85 MHz maximum rising-edge clock, three LVDS data outputs, and a 48-pin TSSOP package. The manufacturer identifies the device as a +3.3 V rising-edge data-strobe LVDS 21-bit Channel Link transmitter with a stated 1.785 Gbps aggregate data rate.
What can replace DS90CR217MTD?
DS90CR217MTD/NOPB is the closest confirmed same-family ordering option because it is listed as the 48-TSSOP version of the same transmitter. Other devices in the comparison listings, including DS90CR216AMTD and DS90C363MTD, require separate verification of bit width, clocking, LVDS output count, timing, and package pinout. No unqualified drop-in replacement should be assumed.
Is DS90CR217MTD the same as DS90CR217MTD/NOPB?
DS90CR217MTD and DS90CR217MTD/NOPB refer to closely related ordering forms of the DS90CR217 family, but the suffix controls orderable-device details such as lead-free construction and terminal finish. The verified distributor result explicitly identifies DS90CR217MTD/NOPB as the alternate for DS90CR217MTD. Confirm the exact device marking and orderable status before treating them as identical.
How should DS90CR217MTD LVDS outputs be routed?
Route the DS90CR217MTD differential outputs as controlled-impedance pairs on a PCB intended for high-speed LVDS signals. Keep the differential pair geometry consistent, minimize discontinuities, and use the termination arrangement specified by the manufacturer datasheet and the receiving device. Do not substitute single-ended routing or arbitrary resistor values without checking the complete interface specification.

Data referensi kejuruteraan untuk DS90CR217MTD — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the DS90CR217MTD when your design needs a 3.3 V, 21-bit parallel-to-LVDS transmitter with rising-edge clocking and up to 85 MHz operation. It is appropriate for display, video, imaging, industrial, and communications links where the receiver and cable infrastructure support the same Channel Link arrangement. Select DS90CR217MTD/NOPB when that is the confirmed orderable form for the intended supply chain. Treat DS90CR216AMTD, DS90C363MTD, and DS90C385AMTX as candidates only after checking input width, clock edge, output count, timing, and pin mapping. Because the original device is identified as NRND, confirm lifecycle status, availability, and any end-of-life planning requirements before production release.

Perbandingan dengan Gantian

Parametr Produk Ini DS90CR217MTD/NOPB DS90CR216AMTD DS90C363MTD DS90C385AMTX
Package 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP 48-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

Penyeberangsung Jelas

  • Directly identified alternate ordering designation (vsDS90CR217MTD/NOPB)
  • High-bandwidth parallel-to-LVDS conversion (vsDS90CR216AMTD)
  • Established DS90 family interface ecosystem (vsDS90C363MTD)

Catatan Desain

Route each LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous reference plane. Avoid stubs, test pads, and unnecessary layer transitions on the data and clock pairs. Keep the transmitter, receiver, and termination arrangement consistent with the manufacturer's recommended Channel Link implementation.

Do not assume that all DS90 family devices are interchangeable simply because they use a 48-TSSOP package. Confirm the input width, clock edge, output lane count, LVDS levels, timing, and pin mapping against the original DS90CR217MTD datasheet. The 48-TSSOP footprint alone does not establish electrical or timing compatibility.

Use the receiver's required termination network and maintain a low-impedance ground return between the transmitter and receiver. Place bypass capacitors close to the supply and ground pins, and inspect the differential-to-common-mode balance at the connector and cable. These practices reduce susceptibility to noise and improve repeatability across cable lengths.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance status requires confirmation from the manufacturer datasheet or product documentation.

Pencarian Berhubungan

DS90CR217MTD nopb DS90CR217MTD datasheet DS90CR217MTD pinout DS90CR217MTD datasheet pdf DS90CR217MTD 48-TSSOP DS90CR217MTD 21-bit transmitter DS90CR217MTD 85 MHz DS90CR217MTD replacement DS90CR217MTD equivalent DS90CR217MTD vs DS90CR216AMTD DS90CR217MTD application circuit Texas Instruments DS90CR217MTD

Komponen dan Tanda berkaitan

Texas Instruments DS90CR217MTD DS90CR217MTD/NOPB DS90CR216AMTD DS90C363MTD DS90C385AMTX DS90CR213MTD DS90C387VJD-TI DS90CF562MTD LVDS Channel Link LVDS transmitter differential signaling CMOS/TTL logic parallel-to-serial interface interface IC surface-mount semiconductor 48-TSSOP 85 MHz clock 1.785 Gbps data rate 3.3 V supply industrial visualization video link imaging system board-to-board communication
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ