DS90CR282MTD - 28-Bit LVDS Channel-Link Receiver | Texas Instruments
部品番号: DS90CR282MTD ✓ 生産中DS90CR282MTD 概要
A Channel-Link receiver is a specialized interface IC that bridges the voltage and signaling domains between a high-speed differential transmitter and downstream parallel logic. The DS90CR282MTD belongs to the broader low-voltage differential signaling interface hierarchy: Channel-Link receiver, differential line receiver, digital interface IC, and semiconductor. Its role is to deserialize or reconstruct parallel data from a compact group of differential conductors, reducing connector pin count while preserving a parallel data presentation to the receiving system.
The principal interface characteristics include a 28-bit parallel data width, four LVDS data streams, LVDS protocol support, and a 4.5 V to 5.5 V supply range. These features make the device applicable to industrial control systems, digital video processing, instrumentation, test equipment, and embedded systems that use a Channel-Link transmitter such as the DS90CR281. The wide parallel output interface allows each recovered bit to be routed directly into FPGA, ASIC, or other digital logic.
Operationally, the receiver relies on differential signaling to reject common-mode voltage and reduce sensitivity to noise encountered along a cable or PCB interconnect. Differential clock recovery coordinates the parallel outputs, while the four LVDS lanes carry groups of serialized data. Board-level implementation must preserve controlled impedance, short return paths, and adequate coupling between the transmitter and receiver. Power and ground distribution should be planned to prevent simultaneous output switching from disturbing adjacent sensitive circuitry.
Typical uses include transferring control and pixel data in video-processing equipment, transporting automation commands between distributed controllers, and carrying parallel bus data over a compact cable connection. The interface is particularly useful when a design already uses a Channel-Link-compatible transmitter and therefore benefits from a standard 28-bit parallel receiver architecture.
A principal design consideration is signal integrity. The differential pairs require matched routing, suitable layer-stack geometry, and compliant LVDS input capacitance. The supply rails need local high-frequency decoupling, while the parallel output timing budget must include receiver latency and clock-alignment requirements. Power sequencing and signal integrity should be evaluated together because a stable supply does not compensate for an incorrectly implemented differential channel.
This product overview combines the confirmed device identity, interface width, supply range, protocol, package, and packaging information with practical guidance for LVDS routing, decoupling, timing, and source selection. It also distinguishes direct drop-in alternatives from related Channel-Link parts that may require a different transmitter, voltage, protocol, or board footprint.
ドロップイン代替品: DS90CR282MTD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90CR282MTD (同一形状・フットプリント) — 相違点: Packaging.
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストDS90CR282MTD 仕様
| Device Type | Receiver |
| Product Family | 28-Bit Channel Link |
| Parallel Data Width | 28 bits |
| LVDS Data Streams | 4 streams |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Protocol | LVDS |
| パッケージ | 56-TSSOP |
| Package Body Width | 6.10 mm |
| Package Body Height | 0.240 mm |
| Packaging | Tube |
| 実装タイプ | Surface Mount |
| Logic Interface | CMOS/TTL |
DS90CR282MTD 0.240 mm ピン配置ガイド
DS90CR282MTD (0.240 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90CR282MTD.
詳細は データシート をご参照ください。
主な用途
DS90CR282MTD の用途: 6 件s: Industrial Control and Automation Links, Digital Video Processing Equipment, Test and Measurement Instrumentation, Embedded Backplane Communication, FPGA Data Acquisition Cards, Telecommunications and Network Equipment.
Industrial Control and Automation Links
DS90CR282MTD is suitable for an industrial automation controller that must receive grouped parallel data from a distant or separately powered subsystem. Its four LVDS streams provide a compact differential transport path, while the 28-bit CMOS/TTL output can connect directly to controller logic operating from a 4.5 V to 5.5 V supply. The design should preserve matched differential-pair geometry, maintain a continuous ground reference, and verify receiver timing against the transmitting equipment. Cable length, data rate, connector losses, and isolation boundaries determine how much additional interface protection and equalization may be required.
おすすめ
Digital Video Processing Equipment
DS90CR282MTD can serve as the receiving boundary in video-processing equipment when an upstream Channel-Link transmitter serializes pixel, control, or configuration data. The receiver restores the data to a 28-bit parallel bus for an FPGA, ASIC, or digital processor, reducing interconnect width compared with carrying all bits individually. The 4.5 V to 5.5 V supply aligns with a conventional 5 V interface domain. Engineering validation must cover video timing, clock alignment, lane skew, connector behavior, and the exact mapping between transmitted bits and downstream logic.
おすすめ
Test and Measurement Instrumentation
DS90CR282MTD is appropriate for test and measurement instruments that separate acquisition or processing hardware from a remote front end. Four differential LVDS streams can carry grouped control or result data across a defined board or cable distance, and the receiver delivers the information as a 28-bit parallel bus for timing-critical processing. Because measurement systems often combine sensitive analog and digital circuitry, the interface section should use controlled-impedance routing, local supply decoupling, and deliberate return-current paths. Validate the supported data rate, receiver latency, and signal-loss margin at the intended connection length.
おすすめ
Embedded Backplane Communication
DS90CR282MTD can be used in an embedded backplane when a central transmitter distributes grouped digital data to receiver modules. The four LVDS streams limit the number of high-speed conductors compared with a 28-bit parallel bus, while the recovered parallel outputs simplify the interface to local programmable logic. The 56-pin TSSOP package supports conventional surface-mount assembly, and tube packaging accommodates production handling. Backplane engineers should account for connector and trace loss, lane-to-lane skew, reference-plane continuity, and the allowable loading of every receiver input.
おすすめ
FPGA Data Acquisition Cards
DS90CR282MTD is useful in an FPGA acquisition card when the source subsystem serializes multiple data channels and the FPGA requires a parallel reconstruction. The receiver's 28-bit output can feed registers or block RAM, allowing the four LVDS streams to represent a wider logical payload than any single pair can carry. The interface operates from a 4.5 V to 5.5 V supply, but the output voltage compatibility must still be checked against the FPGA bank voltage. Layout should minimize stubs, maintain symmetrical pair spacing, and define timing constraints using the receiver's clock and latency characteristics.
おすすめ
Telecommunications and Network Equipment
DS90CR282MTD can support internal high-speed links in telecommunications equipment where a parallel functional block must communicate with another circuit board across a controlled differential connection. Four LVDS streams offer a practical way to carry grouped control, payload, or status bits, and the receiver outputs them in a 28-bit parallel format for downstream line-card logic. The implementation should separate the interface from noisy switching sections, use a solid reference plane, and apply decoupling close to the supply pins. Production qualification should confirm operating temperature, lifecycle status, and environmental compliance for the exact assembled system.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90CR282MTD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Texas Instruments |
| Package | 56-TSSOP |
| Device Type | Receiver |
| Product Family | 28-Bit Channel Link |
| Parallel Data Width | 28 bits |
| LVDS Data Streams | 4 streams |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Logic Interface | CMOS/TTL |
| Packaging | Tube |
主な差別化要因
- Dedicated 28-bit Channel-Link receiver function (vs DS90CR281)
- Conventional 5 V interface supply range (vs DS90CF562MTD)
- Established 56-pin TSSOP production format (vs DS90CR285MTD)
設計ノート
Route the four LVDS data pairs and the associated clock channel as controlled-impedance differential nets on a continuous reference plane. Keep pair spacing and trace geometry matched, avoid stubs, and maintain the same general routing environment across all channels. Consult the manufacturer datasheet for the exact differential pair assignments and polarity before assigning FPGA or ASIC pins.
Place the required input and bypass capacitors close to the DS90CR282MTD supply and ground pins, with short, low-inductance connections. The receiver operates from 4.5 V to 5.5 V, so verify rail tolerance and startup behavior across the complete system. Use the manufacturer recommended capacitance values and ESR characteristics when selecting decoupling components.
Account for cable or PCB-channel loss, connector transitions, source termination, receiver input capacitance, and lane-to-lane skew when establishing the supported link distance. Simulate or measure the complete source-to-receiver channel at the intended data rate. A short bench connection does not guarantee reliable performance over production cable lengths or through connectors.
Do not treat DS90CR281 and DS90CR282MTD as interchangeable devices: one transmits and the other receives. Also avoid choosing a replacement solely because it has 28 outputs or a 56-pin package. Confirm pin-to-pin mapping, differential polarity, supply range, protocol behavior, output timing, package dimensions, and assembly tolerances before approving a substitute.
コンプライアンス情報
The exact compliance declarations for DS90CR282MTD must be confirmed from the manufacturer labeling for the orderable MPN. No RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was confirmed by the product information.