DS90CR583MTD - 65 MHz LVDS FPD Transmitter | Texas Instruments
部品番号: DS90CR583MTD ⚠ ラストタイムバイDS90CR583MTD 概要
An LVDS flat-panel-display link transmitter is an interface IC within the broader display-interface and semiconductor hierarchy. It accepts parallel logic-level pixel data, serializes that data onto low-voltage differential pairs, and transfers the resulting signal to a compatible receiver across a cable or PCB interconnect. By combining data and clock over controlled differential signaling, the interface reduces the number of conductors required compared with a parallel display bus while supporting higher signal integrity than ordinary single-ended transmission.
The DS90CR583 supports 28 CMOS/TTL input bits, four LVDS data outputs, and one LVDS clock output at a maximum signaling rate of 65 MHz. The 4.5 V minimum and 5.5 V maximum supply range suits conventional 5 V display-controller environments. The transmitter samples 28 input bits during every transmitted clock cycle, providing a straightforward mapping between the parallel source data and the serialized differential outputs.
The internal architecture includes parallel-to-serial conversion, clock generation, and a phase-locked transmit clock. The phase-locked clock is transmitted in parallel with the four data streams so that a compatible DS90CR584 receiver can reconstruct the original 28-bit word. This clock-and-data arrangement is important because display timing must remain aligned across every pixel-transfer cycle.
Typical applications include small-format TFT-LCD panels, industrial display controllers, medical diagnostic displays, test and measurement equipment, and legacy flat-panel systems that use FPD-Link or LVDS signaling. The transmitter is most appropriate where the host controller provides 28-bit parallel CMOS data and the display receiver supports the corresponding five-link LVDS architecture.
Designers should use controlled-impedance differential routing, maintain a continuous reference plane, and place bypass capacitors close to the supply pins. The TSSOP footprint requires careful fan-out because 56 leads provide limited routing escape area. Signal-pair length matching and separation from noisy switching nodes are essential for reliable LVDS operation.
This page consolidates the device architecture, interface requirements, lifecycle information, package characteristics, and application-specific design guidance into an engineering-focused reference for evaluating the DS90CR583MTD in legacy flat-panel-display systems.
ドロップイン代替品: DS90CR583MTD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90CR583MTD (同一形状・フットプリント) — 相違点: Device Type, Protocol.
DS90CR583MTDX
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →DS90CR584MTD
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
DS90CR584MTDX
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →DS90CR583MTD
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90CR583
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
DS90CR583MTD 仕様
| Product Type | LVDS flat-panel display link transmitter |
| 最大クロック周波数 | 65 MHz |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Input Data Width | 28 bits CMOS/TTL |
| LVDS Data Outputs | 4 differential streams |
| LVDS Clock Outputs | 1 differential stream |
| Total Driver Output Count | 5 differential outputs |
| Driver/Receiver Configuration | Transmitter |
| Protocol | FPD-Link / LVDS |
| パッケージ | 56-TSSOP |
| Package Width | 6.10 mm |
| Package Body Width | 0.240 inch |
| Packaging | Tube |
| ピン数 | 56 pins |
| 実装タイプ | Surface mount |
DS90CR583MTD 0.240 inch ピン配置ガイド
DS90CR583MTD (0.240 inch パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90CR583MTD.
詳細は データシート をご参照ください。
主な用途
DS90CR583MTD の用途: 6 件s: Legacy TFT-LCD Display Interfaces, Industrial Control Panel Displays, Medical Diagnostic Display Systems, Test and Measurement Equipment, Instrumentation and Process-Control HMIs, Point-of-Sale and Retail Terminals.
Legacy TFT-LCD Display Interfaces
The DS90CR583MTD fits a legacy TFT-LCD link when the display controller supplies 28 parallel CMOS/TTL bits and the panel uses the corresponding FPD-Link architecture. Its four 65 MHz LVDS data streams and separate phase-locked clock provide the serialized link expected by a compatible receiver. The 4.5 V to 5.5 V operating range matches a conventional 5 V display subsystem, while the 56-pin TSSOP supports compact controller boards. Use controlled-impedance routing for all five differential outputs and verify the panel's lane mapping, synchronization requirements, and supported clock rate before layout release.
おすすめ
Industrial Control Panel Displays
The DS90CR583MTD can support an industrial control panel that retains a 28-bit parallel display architecture but requires a low-voltage differential connection between the controller and display electronics. A 65 MHz maximum clock supports the stated FPD-Link operating point, and the five differential outputs separate payload data from the phase-locked clock. This arrangement is useful when cable length, noise immunity, or connector pin count makes a wide parallel bus undesirable. Industrial use still requires confirmation of temperature rating, qualification status, panel timing, and long-term availability before production commitment.
おすすめ
Medical Diagnostic Display Systems
The DS90CR583MTD is appropriate for a medical diagnostic display subsystem when the host controller provides 28 parallel data bits and the monitor accepts an LVDS FPD-Link signal. Differential data streams can reduce sensitivity to common-mode noise and make the interface less susceptible to ground-offset problems than a comparable single-ended parallel bus. The transmitter's four data outputs and dedicated clock provide deterministic organization of each 28-bit transfer. Medical-system design work must additionally verify electrical-safety requirements, applicable qualification, temperature limits, display validation, and the system risk controls required for the intended use.
おすすめ
Test and Measurement Equipment
The DS90CR583MTD can be used in test and measurement equipment that includes a legacy flat-panel display controller requiring an LVDS transmitter. Its 28-bit parallel input and 65 MHz maximum link rate accommodate panel-controller designs built around the DS90CR583/DS90CR584 FPD-Link family, while the dedicated phase-locked clock helps the receiving side maintain a consistent sampling relationship. In instrumentation, placement and return-path control are important because display circuitry may sit near switching converters, motor drivers, or high-current relay networks. Keep the LVDS pairs away from those sources and provide a stable reference plane beneath the link.
おすすめ
Instrumentation and Process-Control HMIs
The DS90CR583MTD is suited to a human-machine interface where a local controller drives a panel over LVDS instead of routing a wide parallel bus through a larger system. The 28-bit input structure maps directly to a typical color display data path, while four differential data outputs and one clock output provide a compact cable interface. A 5 V supply requirement keeps integration straightforward for controllers that already include 5 V power. Designers should verify the receiving display's supported resolution and refresh rate, implement matched differential routing, and provide local decoupling close to the transmitter to limit conducted noise entering the display link.
おすすめ
Point-of-Sale and Retail Terminals
The DS90CR583MTD can support a point-of-sale terminal or retail display controller that retains a 28-bit parallel video source and requires a compact differential connection to a remote LCD panel. Sending the 28-bit payload across four LVDS data lanes plus a clock reduces conductor demand and can improve noise immunity within the enclosure. The device's 4.5 V to 5.5 V range supports integration with 5 V display electronics, and its 65 MHz maximum rate matches the stated FPD-Link class. Before deployment, confirm the panel's timing interface, temperature requirements, cable characteristics, and continuing supply status.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90CR583MTD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90CR583MTDX | DS90CR584MTD | DS90CR584MTDX | DS90CR583MTD | DS90CR583 |
|---|---|---|---|---|---|---|
| Package | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Function | FPD-Link transmitter | FPD-Link transmitter | FPD-Link receiver | FPD-Link receiver | FPD-Link transmitter | FPD-Link transmitter |
| Maximum Clock Frequency | 65 MHz | 65 MHz | 65 MHz | 65 MHz | 65 MHz | 65 MHz |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Parallel Input Width | 28 bits CMOS/TTL | 28 bits CMOS/TTL | 28 bits CMOS/TTL receiver output | 28 bits CMOS/TTL receiver output | 28 bits CMOS/TTL | 28 bits CMOS/TTL |
| LVDS Data Channels | 4 | 4 | 4 receiver inputs | 4 receiver inputs | 4 | 4 |
| Clock Channel | 1 phase-locked transmit-clock output | 1 phase-locked transmit-clock output | 1 phase-locked receive-clock output | 1 phase-locked receive-clock output | 1 phase-locked transmit-clock output | 1 phase-locked transmit-clock output |
| Protocol | FPD-Link / LVDS | FPD-Link / LVDS | FPD-Link / LVDS | FPD-Link / LVDS | FPD-Link / LVDS | FPD-Link / LVDS |
| Original Manufacturer | National Semiconductor | National Semiconductor | National Semiconductor | National Semiconductor | National Semiconductor | National Semiconductor |
主な差別化要因
- Direct 28-bit parallel-to-LVDS serialization (vs DS90CR584MTD)
- Dedicated phase-locked clock channel (vs DS90CR584MTDX)
- Established 65 MHz FPD-Link architecture (vs DS90CR583)
設計ノート
Route all LVDS pairs as tightly coupled differential nets with a continuous reference plane directly beneath them. Maintain equal intra-pair spacing and matched length where the interconnect topology requires it. Avoid plane splits, test-point stubs, and unnecessary layer transitions because those discontinuities can degrade the 65 MHz signal. Keep the parallel CMOS/TTL inputs away from the LVDS outputs to reduce crosstalk into the serialized link.
Place supply bypass capacitors close to the device's supply and ground pins, and provide a low-impedance ground-plane connection for every ground lead. The 56-pin TSSOP has limited escape space, so plan fan-out before fixing the component orientation. Confirm pin-1 location, pin numbering, and exposed pad treatment against the manufacturer pin-description table; do not infer connections solely from the package dimensions.
Preserve the phase relationship between the four data links and the dedicated clock link by using consistent trace geometry and avoiding unrelated high-speed activity near these nets. If the link traverses a cable or connector, specify controlled impedance and validate the complete transmitter-to-receiver path. The transmitter supports up to 65 MHz, but usable link margin also depends on loss, skew, noise, and the receiving display.
Do not interchange the DS90CR583 transmitter with a DS90CR584 receiver on the assumption that their shared family name makes them equivalent. The transmitter accepts parallel CMOS/TTL data and creates the LVDS streams, while the receiver performs the opposite function. Also verify the exact ordering suffix, temperature grade, package orientation, and lifecycle requirements before rebuilding a last-time-buy assembly.
コンプライアンス情報
The available manufacturer and distributor records do not state the requested compliance statuses for this ordering code. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification documentation before regulated deployment.