DS90CR288MTD - 28-Bit 75MHz LVDS Receiver | Texas Instruments
部品番号: DS90CR288MTD ✓ 生産中DS90CR288MTD 概要
A channel-link receiver is an interface IC that converts low-voltage differential signaling into parallel CMOS or TTL-compatible data. LVDS belongs to the broader differential-signal interface hierarchy, where low voltage swing, common-mode control, and balanced routing reduce susceptibility to noise. The DS90CR288MTD is consequently positioned between external data-transmission hardware and the digital logic, FPGA, display, or image-processing subsystem that consumes the recovered parallel data.
The device supports 28 bits across four receiver channels and uses rising-edge data-strobe signaling. Its stated operating frequency is 75 MHz, while its 3 V to 3.6 V supply range suits 3.3 V digital systems. The receiver architecture is intended for point-to-point cable or PCB links carrying serialized parallel data, including video, imaging, control, and industrial communication systems. The transmitter converts parallel source data into differential LVDS streams, while the receiver performs the complementary conversion at the far end of the link.
The 56-TSSOP package provides a practical surface-mount interface for systems requiring 28 parallel data bits and several control and power pins. Because the part exposes many high-speed and low-voltage signals, layout quality directly affects signal integrity. Differential impedance-controlled routing, matched pair length adjustment, a solid ground plane, and careful separation from noisy power converters are important. Input and bypass connections should also be arranged to minimize loop area and maintain a clean return path.
DS90CR288MTD is appropriate when the system already uses a compatible Channel Link transmitter and requires a dedicated 28-bit LVDS receiver. The interface is preferable to converting parallel data through a general-purpose transceiver when the PCB already contains the required 56-TSSOP footprint. The main engineering trade-off is that this is a specialized receiver: its function, pinout, supply requirements, and data-strobe convention must match the transmitter and the receiving logic.
For reliable implementation, use the manufacturer datasheet pin description, recommended decoupling, and reference-layout guidance without modification. Confirm the exact clock topology, input mapping, termination arrangement, exposed-pad requirements, and signal amplitudes during schematic review. This page combines the confirmed operating characteristics, packaging information, sourcing structure, and engineering guidance needed to evaluate DS90CR288MTD before committing the PCB layout.
Once the transmitter, receiver, and downstream logic are verified as a complete link, DS90CR288MTD provides a direct 28-bit LVDS receiving path in 3.3 V systems. Its fixed protocol and package make design reuse straightforward, but pin-level compatibility and link-level timing must be checked rather than assumed from the Channel Link label alone.
ドロップイン代替品: DS90CR288MTD — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
DS90CR288AMTD
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
DS90CR288A
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
DS90CR288MTD 仕様
| Product Type | 28-bit LVDS Channel Link receiver |
| Number of Drivers/Receivers | 4/28 |
| Receiver Type | Receiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Data Rate or Clock Frequency | 75 MHz |
| Number of Data Bits | 28 bits |
| Number of Data Channels | 4 channels |
| Signaling Protocol | LVDS |
| Data-Strobe Edge | Rising edge |
| パッケージ | 56-TSSOP |
| Package Width | 0.240 inch |
| Package Length | 6.10 mm |
| ピン数 | 56 pins |
| 実装タイプ | Surface mount |
| Packaging | Tube |
DS90CR288MTD 6.10 mm ピン配置ガイド
DS90CR288MTD (6.10 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90CR288MTD.
詳細は データシート をご参照ください。
主な用途
DS90CR288MTD の用途: 6 件s: Industrial Camera Data Links, Video Processing Backplanes, FPGA Sensor Data Acquisition, Medical Imaging Interfaces, High-Speed Control Data Transport, Test and Measurement Equipment.
Industrial Camera Data Links
The DS90CR288MTD fits industrial imaging systems that transfer 28 bits of parallel camera data across a short, noise-sensitive LVDS connection. Its four receiver channels recover the transmitted differential streams at up to 75 MHz, while the 3 V to 3.6 V supply range integrates naturally with 3.3 V imaging logic. Place the receiver near the cable or board-to-board connector, match each differential pair, and provide local supply decoupling. The link can simplify cable reach and signal integrity compared with routing 28 single-ended lines over a long interconnect.
おすすめ
Video Processing Backplanes
The DS90CR288MTD is suitable for recovering a 28-bit video stream on a backplane or multi-board system where parallel routing would increase noise and skew risk. The device accepts four LVDS data channels and operates at up to 75 MHz, providing a defined receiving endpoint for a compatible Channel Link transmitter. Designers should control differential impedance, maintain pair-length balance, and separate the link from switching regulators and high-current digital returns. The recovered parallel data can then feed an FPGA or dedicated video processor without adding another external line receiver.
おすすめ
FPGA Sensor Data Acquisition
The DS90CR288MTD can serve as the receiving element in an FPGA-based sensor acquisition chain that receives 28 bits over four LVDS channels. A compatible transmitter serializes sensor or ADC data, and the receiver returns it to parallel form for FPGA capture at the stated 75 MHz operating limit. The 3.3 V supply requirement supports integration with contemporary programmable logic. Engineering attention should focus on clock alignment, connector or cable return paths, receiver placement near the source, and verifying that recovered data timing meets the FPGA input constraints.
おすすめ
Medical Imaging Interfaces
The DS90CR288MTD can participate in medical imaging equipment where an image-acquisition board transfers a wide parallel data stream across an internal balanced link. Its 28-bit capacity and four LVDS receiver channels reduce the number of sensitive single-ended traces, while the 75 MHz operating limit defines the supported link rate. The component does not perform diagnostics or image processing itself, so system validation must cover clocking, data integrity, isolation requirements, and applicable medical standards. Use the manufacturer electrical characteristics and application guidance to establish the final channel margin.
おすすめ
High-Speed Control Data Transport
The DS90CR288MTD is appropriate for industrial control systems that need a compact, dedicated path for a 28-bit command or status bus. Four LVDS channels can carry the data across a board-to-board connection while limiting signal-current excursions and improving noise tolerance relative to long single-ended routing. The receiver's 3 V to 3.6 V operating range supports 3.3 V control logic, while its 75 MHz ceiling provides ample margin for many command and configuration paths. Validate latency, clock recovery behavior, and fault tolerance against the system's safety requirements.
おすすめ
Test and Measurement Equipment
The DS90CR288MTD can receive a wide parallel data path in test and measurement instruments that exchange captured, generated, or processed data between circuit boards. Four differential channels provide a practical way to move 28 bits without routing every bit as a single-ended board trace. At the 3.3 V nominal supply and 75 MHz operating limit, the receiver is suited to controlled internal interconnects rather than unrestricted cable use. Designers should evaluate connector loss, grounding, shielding, and clock architecture, then verify the complete transmitter-to-receiver path during signal-integrity testing.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90CR288MTD — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
設計ノート
Route the four LVDS input pairs as controlled-impedance, tightly coupled differential nets with continuous reference-plane support. Keep the receiver close to the cable or board-to-board connector, minimize layer transitions and stubs, and match pair geometry through the interconnect. The receiver must share an uninterrupted low-impedance return path with the transmitter to preserve differential voltage and common-mode control.
Place the power bypass capacitors close to the DS90CR288MTD supply and ground pins using the manufacturer-recommended topology. Keep the switching loop area small and connect the exposed or surrounding ground structure directly to a solid plane. Avoid placing noisy converters, clocks, or high-current return paths beside the differential inputs because even a balanced signal can lose margin when common-mode noise and impedance discontinuities combine.
Do not treat the DS90CR285MTD transmitter as a substitute receiver; the two devices have opposite signal directions and different stated operating limits of 66 MHz and 75 MHz. Likewise, do not assume that every 28-bit Channel Link package has an identical pinout. Verify data, clock, enable, supply, and ground assignments for the exact MPN and confirm that the source transmitter supports the receiver's clocking and data-strobe convention.
Validate the complete link using the intended cables, connectors, PCB stack-up, and clock source rather than relying only on a bench prototype with short wires. Probe differential signal quality at the receiver pins and check rise time, differential voltage, common-mode range, clock recovery, and data timing. The 75 MHz figure describes the receiver's operating frequency, but end-to-end margin also depends on transmitter output, interconnect loss, jitter, and downstream logic timing.
コンプライアンス情報
The available product listings do not state a definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact MPN. These fields require confirmation from the manufacturer or an authorized production record.