EFM32TG230F16-D-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
部品番号: EFM32TG230F16-D-QFN64 ✓ 生産中EFM32TG230F16-D-QFN64 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface circuitry on one device. The EFM32TG230 belongs to the Tiny Gecko family within the broader ARM Cortex-M microcontroller hierarchy. Its combination of a 32 MHz Cortex-M3 core and low-power operating modes makes it suitable for battery-powered and energy-conscious products where response time and standby consumption are both important.
The EFM32TG230F16-D-QFN64 combines a 32-bit single-core Cortex-M3 processor, 32 MHz operating speed, and 16 KB of Flash with a compact 64-QFN package. The family is documented as consuming as little as 0.6 uA in Stop mode and 150 uA/MHz in Run mode. These figures illustrate the device's suitability for portable instruments, sensor nodes, connected accessories, and industrial modules that spend substantial time in low-energy states.
Autonomous peripherals are a central architectural feature of the Tiny Gecko platform. Hardware-managed timing, sensing, communications, and data movement can allow the processor to remain asleep while peripheral events are handled. Combined with fast wake-up behavior, this architecture can reduce both system latency and active-processing time without requiring a large external sensor or communication subsystem.
Typical embedded uses include low-power sensor interfaces, industrial condition-monitoring nodes, compact control modules, battery-operated accessories, and portable measurement products. The 16 KB Flash capacity is best suited to applications with a moderate firmware footprint, while the 32-bit Cortex-M3 instruction set provides more headroom than an 8-bit MCU for protocol handling, control logic, and concurrent peripheral management.
PCB design should account for the QFN thermal-pad connection, exposed-pad soldering, and decoupling requirements. Place the input and bulk capacitors close to their associated supply pins, preserve a continuous ground path beneath the device, and follow the manufacturer land-pattern and assembly recommendations. Firmware and peripheral configuration should also be checked against the EFM32TG230 datasheet before production release.
This product record combines device specifications, package information, sourcing guidance, and engineering-focused replacement analysis. It also distinguishes a genuine same-package upgrade from broader functional alternatives, helping designers make a controlled migration without confusing similar Cortex-M products with pin-compatible replacements.
ドロップイン代替品: EFM32TG230F16-D-QFN64 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EFM32TG230F16-D-QFN64 (同一形状・フットプリント) — 相違点: Flash Memory, Product Type, Supply Voltage Range, Architecture, Package.
EFM32TG230F32-QFN64
✅ ドロップイン価格はお問い合わせください
データシートを見る →EFM32TG230F16-D-QFN64 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Microcontroller Family | EFM32 Tiny Gecko |
| Processor Core | ARM Cortex-M3 |
| Core Count | 1 core |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 KB (16K x 8) |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Run Mode Current | 150 uA/MHz |
| Stop Mode Current | 0.6 uA |
| パッケージ | 64-QFN (9 x 9 mm) |
| 実装タイプ | Surface mount |
| Output State Retention | Supported |
EFM32TG230F16-D-QFN64 64-qfn (9 x 9 mm) ピン配置ガイド
EFM32TG230F16-D-QFN64 (64-qfn (9 x 9 mm) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: EFM32TG230F16-D-QFN64.
詳細は データシート をご参照ください。
主な用途
EFM32TG230F16-D-QFN64 の用途: 6 件s: Battery-Powered Sensor Node, Industrial Condition Monitoring, Portable Medical Accessory, Battery Charging Controller, Smart Home Sensor Interface, Compact Data Acquisition Module.
Battery-Powered Sensor Node
The EFM32TG230F16-D-QFN64 fits compact sensor nodes that combine a 32-bit Cortex-M3 processor with long periods of low-energy operation. Its 16 KB of Flash can hold the acquisition, filtering, and communication-control firmware required for a focused embedded product. Stop mode is specified as low as 0.6 uA, while Run mode is 150 uA/MHz, allowing the firmware to wake for measurements and return to sleep. The main constraint is the relatively modest Flash capacity, which should be checked against the final firmware image.
おすすめ
Industrial Condition Monitoring
The EFM32TG230F16-D-QFN64 is suitable for compact condition-monitoring modules that sample sensors, apply digital filtering, and report measurements through a low-speed communications interface. Its 32 MHz Cortex-M3 core provides enough arithmetic capability for real-time signal handling without requiring a higher-power processor. A 1.98 V to 3.8 V supply range supports common 2.5 V and 3.3 V designs. The 64-QFN 9 x 9 mm package also preserves board area in distributed sensor nodes.
おすすめ
Portable Medical Accessory
The EFM32TG230F16-D-QFN64 can serve as the controller in a portable medical accessory where low standby energy, compact size, and deterministic control are important. The 32-bit Cortex-M3 core can manage sensor reads, button input, and a local status display, while the Stop-mode specification of 0.6 uA reduces energy use between interactions. Firmware partitioning should account for the 16 KB Flash limit, and the exact ordering code must be reviewed for the intended temperature, reliability, and regulatory environment.
おすすめ
Battery Charging Controller
The EFM32TG230F16-D-QFN64 is appropriate for small battery-powered charging or power-path modules that require precise state-machine control and low idle consumption. The 32 MHz processor can supervise voltage and current measurements, manage status indicators, and coordinate timing without adding a separate high-power processor. Because the device supports a 1.98 V to 3.8 V operating range, system-level rail design is flexible, but charger safety thresholds, cell chemistry, and thermal protection must remain independent of the MCU where required.
おすすめ
Smart Home Sensor Interface
The EFM32TG230F16-D-QFN64 fits smart-home sensor interfaces that combine multiple digital inputs with a low-power communications processor. Its autonomous peripheral architecture allows supported events to be handled efficiently, and the Cortex-M3 core provides a conventional firmware environment for protocols and application logic. The 16 KB Flash capacity favors a compact application with tightly controlled code size. If wireless firmware, secure updates, or extensive device management is required, EFM32TG230F32-QFN64 offers the same package and platform with twice the Flash.
おすすめ
Compact Data Acquisition Module
The EFM32TG230F16-D-QFN64 supports compact data-acquisition modules that require timing, control, and local processing close to the sensors. Its single-core 32 MHz Cortex-M3 architecture can execute acquisition sequencing and data preparation, while low-energy modes limit consumption between sample events. The 64-QFN 9 x 9 mm package supports dense instrument designs, and the 1.98 V to 3.8 V range accommodates multiple embedded power architectures. The final memory budget must be checked against buffering, calibration, and communications firmware.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EFM32TG230F16-D-QFN64 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EFM32TG230F32-QFN64 |
|---|---|---|
| Brand | Silicon Labs | Silicon Labs |
| Package | 64-QFN (9 x 9 mm) | 64-QFN (9 x 9 mm) |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz |
| Flash Memory | 16 KB (16K x 8) | 32 KB |
| Run Mode Current | 150 uA/MHz | 150 uA/MHz |
| Stop Mode Current | 0.6 uA | 0.6 uA |
| Special Features | Output state retention and wake-up from Shutoff Mode | Autonomous peripherals and energy-saving modes |
主な差別化要因
- Lower Flash configuration supports a fixed-cost target (vs EFM32TG230F32-QFN64)
- Identical package and CPU speed for controlled evaluation (vs EFM32TG230F32-QFN64)
- Ultra-low-power platform for battery-oriented designs (vs EFM32TG230F32-QFN64)
設計ノート
Follow the EFM32TG230 datasheet land pattern for the 64-QFN 9 x 9 mm package, including its exposed thermal pad and the required via arrangement. Place the device-side input, output, and bulk decoupling capacitors as close as practical to their supply pins. Maintain a low-impedance ground plane beneath the package and avoid routing fast or sensitive signals through the exposed-pad region.
Design the 1.98 V to 3.8 V supply path for both active and transient conditions, including processor startup, flash writes, and simultaneous peripheral activity. Confirm that the selected regulator supports the expected load steps and that brownout behavior matches the firmware reset strategy. Place additional bulk energy close enough to the MCU to support transient response without creating excessive input-capacitance concerns.
Do not treat every 64-QFN EFM32 or Cortex-M3 device as a drop-in replacement. The EFM32TG230F32-QFN64 is a controlled same-family candidate because it retains the TG230 platform, core speed, and package, but its Flash map and device configuration still require review. Recheck the complete pin list, exposed-pad connection, clock setup, boot pins, debugger interface, and firmware image before substituting it in production hardware.
コンプライアンス情報
The exact ordering code's compliance declarations were not stated in the available product records. Obtain current manufacturer compliance documentation before production release.