EFM32TG230F16-D-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
부품 번호: EFM32TG230F16-D-QFN64 ✓ 활성EFM32TG230F16-D-QFN64 개요
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface circuitry on one device. The EFM32TG230 belongs to the Tiny Gecko family within the broader ARM Cortex-M microcontroller hierarchy. Its combination of a 32 MHz Cortex-M3 core and low-power operating modes makes it suitable for battery-powered and energy-conscious products where response time and standby consumption are both important.
The EFM32TG230F16-D-QFN64 combines a 32-bit single-core Cortex-M3 processor, 32 MHz operating speed, and 16 KB of Flash with a compact 64-QFN package. The family is documented as consuming as little as 0.6 uA in Stop mode and 150 uA/MHz in Run mode. These figures illustrate the device's suitability for portable instruments, sensor nodes, connected accessories, and industrial modules that spend substantial time in low-energy states.
Autonomous peripherals are a central architectural feature of the Tiny Gecko platform. Hardware-managed timing, sensing, communications, and data movement can allow the processor to remain asleep while peripheral events are handled. Combined with fast wake-up behavior, this architecture can reduce both system latency and active-processing time without requiring a large external sensor or communication subsystem.
Typical embedded uses include low-power sensor interfaces, industrial condition-monitoring nodes, compact control modules, battery-operated accessories, and portable measurement products. The 16 KB Flash capacity is best suited to applications with a moderate firmware footprint, while the 32-bit Cortex-M3 instruction set provides more headroom than an 8-bit MCU for protocol handling, control logic, and concurrent peripheral management.
PCB design should account for the QFN thermal-pad connection, exposed-pad soldering, and decoupling requirements. Place the input and bulk capacitors close to their associated supply pins, preserve a continuous ground path beneath the device, and follow the manufacturer land-pattern and assembly recommendations. Firmware and peripheral configuration should also be checked against the EFM32TG230 datasheet before production release.
This product record combines device specifications, package information, sourcing guidance, and engineering-focused replacement analysis. It also distinguishes a genuine same-package upgrade from broader functional alternatives, helping designers make a controlled migration without confusing similar Cortex-M products with pin-compatible replacements.
드롭인 대체품: EFM32TG230F16-D-QFN64 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EFM32TG230F16-D-QFN64 (동일 폼 팩터 및 풋프린트) — 차이점: Flash Memory, Product Type, Supply Voltage Range, Architecture, Package.
EFM32TG230F32-QFN64
✅ 드롭인가격 문의
데이터시트 보기 →EFM32TG230F16-D-QFN64 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Microcontroller Family | EFM32 Tiny Gecko |
| Processor Core | ARM Cortex-M3 |
| Core Count | 1 core |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 KB (16K x 8) |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Run Mode Current | 150 uA/MHz |
| Stop Mode Current | 0.6 uA |
| 패키지 | 64-QFN (9 x 9 mm) |
| 실장 유형 | Surface mount |
| Output State Retention | Supported |
EFM32TG230F16-D-QFN64 64-qfn (9 x 9 mm) 핀 구성 가이드
EFM32TG230F16-D-QFN64(64-qfn (9 x 9 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EFM32TG230F16-D-QFN64.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EFM32TG230F16-D-QFN64 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Node, Industrial Condition Monitoring, Portable Medical Accessory, Battery Charging Controller, Smart Home Sensor Interface, Compact Data Acquisition Module.
Battery-Powered Sensor Node
The EFM32TG230F16-D-QFN64 fits compact sensor nodes that combine a 32-bit Cortex-M3 processor with long periods of low-energy operation. Its 16 KB of Flash can hold the acquisition, filtering, and communication-control firmware required for a focused embedded product. Stop mode is specified as low as 0.6 uA, while Run mode is 150 uA/MHz, allowing the firmware to wake for measurements and return to sleep. The main constraint is the relatively modest Flash capacity, which should be checked against the final firmware image.
추천
Industrial Condition Monitoring
The EFM32TG230F16-D-QFN64 is suitable for compact condition-monitoring modules that sample sensors, apply digital filtering, and report measurements through a low-speed communications interface. Its 32 MHz Cortex-M3 core provides enough arithmetic capability for real-time signal handling without requiring a higher-power processor. A 1.98 V to 3.8 V supply range supports common 2.5 V and 3.3 V designs. The 64-QFN 9 x 9 mm package also preserves board area in distributed sensor nodes.
추천
Portable Medical Accessory
The EFM32TG230F16-D-QFN64 can serve as the controller in a portable medical accessory where low standby energy, compact size, and deterministic control are important. The 32-bit Cortex-M3 core can manage sensor reads, button input, and a local status display, while the Stop-mode specification of 0.6 uA reduces energy use between interactions. Firmware partitioning should account for the 16 KB Flash limit, and the exact ordering code must be reviewed for the intended temperature, reliability, and regulatory environment.
추천
Battery Charging Controller
The EFM32TG230F16-D-QFN64 is appropriate for small battery-powered charging or power-path modules that require precise state-machine control and low idle consumption. The 32 MHz processor can supervise voltage and current measurements, manage status indicators, and coordinate timing without adding a separate high-power processor. Because the device supports a 1.98 V to 3.8 V operating range, system-level rail design is flexible, but charger safety thresholds, cell chemistry, and thermal protection must remain independent of the MCU where required.
추천
Smart Home Sensor Interface
The EFM32TG230F16-D-QFN64 fits smart-home sensor interfaces that combine multiple digital inputs with a low-power communications processor. Its autonomous peripheral architecture allows supported events to be handled efficiently, and the Cortex-M3 core provides a conventional firmware environment for protocols and application logic. The 16 KB Flash capacity favors a compact application with tightly controlled code size. If wireless firmware, secure updates, or extensive device management is required, EFM32TG230F32-QFN64 offers the same package and platform with twice the Flash.
추천
Compact Data Acquisition Module
The EFM32TG230F16-D-QFN64 supports compact data-acquisition modules that require timing, control, and local processing close to the sensors. Its single-core 32 MHz Cortex-M3 architecture can execute acquisition sequencing and data preparation, while low-energy modes limit consumption between sample events. The 64-QFN 9 x 9 mm package supports dense instrument designs, and the 1.98 V to 3.8 V range accommodates multiple embedded power architectures. The final memory budget must be checked against buffering, calibration, and communications firmware.
추천
추천 제품 요약
엔지니어링 참조 데이터: EFM32TG230F16-D-QFN64 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EFM32TG230F32-QFN64 |
|---|---|---|
| Brand | Silicon Labs | Silicon Labs |
| Package | 64-QFN (9 x 9 mm) | 64-QFN (9 x 9 mm) |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz |
| Flash Memory | 16 KB (16K x 8) | 32 KB |
| Run Mode Current | 150 uA/MHz | 150 uA/MHz |
| Stop Mode Current | 0.6 uA | 0.6 uA |
| Special Features | Output state retention and wake-up from Shutoff Mode | Autonomous peripherals and energy-saving modes |
주요 차별점
- Lower Flash configuration supports a fixed-cost target (vs EFM32TG230F32-QFN64)
- Identical package and CPU speed for controlled evaluation (vs EFM32TG230F32-QFN64)
- Ultra-low-power platform for battery-oriented designs (vs EFM32TG230F32-QFN64)
설계 노트
Follow the EFM32TG230 datasheet land pattern for the 64-QFN 9 x 9 mm package, including its exposed thermal pad and the required via arrangement. Place the device-side input, output, and bulk decoupling capacitors as close as practical to their supply pins. Maintain a low-impedance ground plane beneath the package and avoid routing fast or sensitive signals through the exposed-pad region.
Design the 1.98 V to 3.8 V supply path for both active and transient conditions, including processor startup, flash writes, and simultaneous peripheral activity. Confirm that the selected regulator supports the expected load steps and that brownout behavior matches the firmware reset strategy. Place additional bulk energy close enough to the MCU to support transient response without creating excessive input-capacitance concerns.
Do not treat every 64-QFN EFM32 or Cortex-M3 device as a drop-in replacement. The EFM32TG230F32-QFN64 is a controlled same-family candidate because it retains the TG230 platform, core speed, and package, but its Flash map and device configuration still require review. Recheck the complete pin list, exposed-pad connection, clock setup, boot pins, debugger interface, and firmware image before substituting it in production hardware.
규정 준수 정보
The exact ordering code's compliance declarations were not stated in the available product records. Obtain current manufacturer compliance documentation before production release.