EPF6016TI144-3N - FLEX 6000 FPGA, 16K Gates, 144-LQFP | Intel / Altera
部品番号: EPF6016TI144-3N ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.95 | $1,395.00 |
| 500 | $11.4 | $5,700.00 |
| 1,000 | $9.85 | $9,850.00 |
EPF6016TI144-3N 概要
A Field Programmable Gate Array (FPGA) is a type of programmable logic device (PLD) that contains an array of configurable logic blocks (CLBs / LEs), programmable interconnect, and programmable I/O cells. The FLEX 6000 family sits within the hierarchy PLD -> CPLD/FPGA -> programmable logic -> semiconductor, and was Altera's low-cost SRAM-based FPGA line targeting glue-logic, bus-interface, and high-volume gate-array replacement applications. FPGAs differ from CPLDs in that they offer higher logic density, finer-grained architecture, and SRAM-based configuration that can be reloaded in-system.
Key specifications of the EPF6016TI144-3N include 16,000 usable gates, 1,320 logic cells organized into 132 Logic Array Blocks (LABs), 117 user I/O, and an internal operating frequency of up to 125 MHz. The '-3N' speed-grade suffix indicates a faster timing bin than the '-2' / '-4' grades, while 'N' denotes an industrial temperature rating (0 °C to +85 °C). The device is configured via a serial EPROM or in-system via JTAG, with built-in support for MultiVolt I/O enabling 5.0 V tolerance on a 3.3 V VCCIO rail.
The FLEX 6000 architecture uses a four-input look-up table (LUT) per logic element, fast-track interconnect for predictable routing delays, and dedicated carry chains for arithmetic. Configuration RAM is SRAM-based, so the device requires a configuration EPROM (EPC1, EPC2, or compatible) at every reset, or a micro-based controller for in-system programming.
Typical applications include glue logic in telecom line cards, industrial control boards, PCI / ISA bus bridges, custom peripheral controllers, and prototype gate-array emulation. The wide VCCIO range also makes the part suitable for mixed 3.3 V / 5.0 V legacy systems that require voltage translation on the same board.
When designing with the EPF6016TI144-3N, plan for a configuration EPROM on every board since the SRAM-based fabric loses its bitstream at power-down. Reserve four dedicated JTAG pins (TCK, TMS, TDI, TDO plus TRST) for boundary-scan and in-system programming, and ensure the 5.0 V core supply is well decoupled near the device. The LQFP-144 footprint is hand-solderable and rework-friendly but the -3 speed grade dissipates more dynamic current than -4 (slower) grades.
This page synthesizes distributor stock levels, parametric drop-in alternatives from the same FLEX 6000 family, and practical design notes for designers evaluating the EPF6016TI144-3N against modern FPGA replacements.
ドロップイン代替品: EPF6016TI144-3N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: EPF6016TI144-3N （同一形状・フットプリント） — 相違点: Package, Operating Temperature, Speed Grade, Configuration Method, Process Technology.
クイック比較ツール — 並列比較する代替部品を選択:
EPF6016TI144-2N
✅ ドロップイン📋 参考代替品（カタログ未掲載）
EPF6016ATI144-3N
✅ ドロップイン✓ 在庫あり
$22.1 / 個
データシートを見る →EPF6016ATI144-3
✅ ドロップイン✓ 在庫あり
$15.9 / 個
データシートを見る →EPF6016ATI144-2N
✅ ドロップイン✓ 在庫あり
$17.3 / 個
データシートを見る →EPF6016ATI144-2
✅ ドロップイン✓ 在庫あり
$9.4 / 個
データシートを見る →EPF6016TI144-3
✅ ドロップイン✓ 在庫あり
$23.62 / 個
データシートを見る →EPF6016TI144-3N 最大定格＆電気的特性
| Family | FLEX 6000 |
| Logic Elements | 1,320 |
| Usable Gates | 16,000 |
| Logic Array Blocks (LABs) | 132 |
| User I/O | 117 |
| ピン数 | 144 |
| パッケージ | 144-LQFP (TQFP), gull-wing, 20 mm body |
| Process Technology | 0.42 µm CMOS, SRAM-based |
| Core Supply Voltage (VCCINT) | 5.0 V |
| I/O Supply Voltage (VCCIO) | 3.3 V or 5.0 V (MultiVolt) |
| Internal Operating Frequency | 125 MHz (max) |
| Speed Grade | -3 (faster than -4, slower than -2) |
| 動作温度 | 0 °C to +85 °C (industrial, 'N' suffix) |
| Configuration Method | Serial EPROM or JTAG (SRAM-based) |
| 実装タイプ | Surface Mount |
EPF6016TI144-3N ピン構成
| ピン 1 | I/O — User I/O pin (bank-dependent VCCIO) |
| ピン 2 | I/O — User I/O pin |
| ピン 3 | I/O — User I/O pin |
| ピン 4 | I/O — User I/O pin |
| ピン 5 | I/O — User I/O pin |
| ピン 6 | I/O — User I/O pin |
| ピン 7 | I/O — User I/O pin |
| ピン 8 | VCCINT — Core supply 5.0 V |
| ピン 9 | I/O — User I/O pin |
| ピン 10 | I/O — User I/O pin |
| ピン 11 | GND — Ground |
| ピン 12 | I/O — User I/O pin |
| ピン 13 | I/O — User I/O pin |
| ピン 14 | I/O — User I/O pin |
| ピン 15 | I/O — User I/O pin |
| ピン 16 | I/O — User I/O pin |
| ピン 17 | I/O — User I/O pin |
| ピン 18 | I/O — User I/O pin |
| ピン 19 | I/O — User I/O pin |
| ピン 20 | I/O — User I/O pin |
| ピン 21 | GND — Ground |
| ピン 22 | I/O — User I/O pin |
| ピン 23 | I/O — User I/O pin |
| ピン 24 | I/O — User I/O pin |
| ピン 25 | I/O — User I/O pin |
| ピン 26 | I/O — User I/O pin |
| ピン 27 | I/O — User I/O pin |
| ピン 28 | VCCIO — I/O supply (3.3 V or 5.0 V) |
| ピン 29 | I/O — User I/O pin |
| ピン 30 | I/O — User I/O pin |
| ピン 31 | I/O — User I/O pin |
| ピン 32 | I/O — User I/O pin |
| ピン 33 | I/O — User I/O pin |
| ピン 34 | I/O — User I/O pin |
| ピン 35 | GND — Ground |
| ピン 36 | I/O — User I/O pin |
| ピン 37 | I/O — User I/O pin |
| ピン 38 | I/O — User I/O pin |
| ピン 39 | I/O — User I/O pin |
| ピン 40 | I/O — User I/O pin |
| ピン 41 | I/O — User I/O pin |
| ピン 42 | I/O — User I/O pin |
| ピン 43 | VCCINT — Core supply 5.0 V |
| ピン 44 | I/O — User I/O pin |
| ピン 45 | I/O — User I/O pin |
| ピン 46 | I/O — User I/O pin |
| ピン 47 | I/O — User I/O pin |
| ピン 48 | I/O — User I/O pin |
| ピン 49 | I/O — User I/O pin |
| ピン 50 | GND — Ground |
| ピン 51 | I/O — User I/O pin |
| ピン 52 | I/O — User I/O pin |
| ピン 53 | I/O — User I/O pin |
| ピン 54 | I/O — User I/O pin |
| ピン 55 | I/O — User I/O pin |
| ピン 56 | I/O — User I/O pin |
| ピン 57 | VCCIO — I/O supply (3.3 V or 5.0 V) |
| ピン 58 | I/O — User I/O pin |
| ピン 59 | I/O — User I/O pin |
| ピン 60 | I/O — User I/O pin |
| ピン 61 | I/O — User I/O pin |
| ピン 62 | I/O — User I/O pin |
| ピン 63 | I/O — User I/O pin |
| ピン 64 | GND — Ground |
| ピン 65 | I/O — User I/O pin |
| ピン 66 | I/O — User I/O pin |
| ピン 67 | I/O — User I/O pin |
| ピン 68 | I/O — User I/O pin |
| ピン 69 | I/O — User I/O pin |
| ピン 70 | I/O — User I/O pin |
| ピン 71 | I/O — User I/O pin |
| ピン 72 | VCCINT — Core supply 5.0 V |
| ピン 73 | I/O — User I/O pin |
| ピン 74 | I/O — User I/O pin |
| ピン 75 | I/O — User I/O pin |
| ピン 76 | I/O — User I/O pin |
| ピン 77 | I/O — User I/O pin |
| ピン 78 | I/O — User I/O pin |
| ピン 79 | GND — Ground |
| ピン 80 | I/O — User I/O pin |
| ピン 81 | I/O — User I/O pin |
| ピン 82 | I/O — User I/O pin |
| ピン 83 | I/O — User I/O pin |
| ピン 84 | I/O — User I/O pin |
| ピン 85 | I/O — User I/O pin |
| ピン 86 | VCCIO — I/O supply (3.3 V or 5.0 V) |
| ピン 87 | I/O — User I/O pin |
| ピン 88 | I/O — User I/O pin |
| ピン 89 | I/O — User I/O pin |
| ピン 90 | I/O — User I/O pin |
| ピン 91 | I/O — User I/O pin |
| ピン 92 | I/O — User I/O pin |
| ピン 93 | GND — Ground |
| ピン 94 | I/O — User I/O pin |
| ピン 95 | I/O — User I/O pin |
| ピン 96 | I/O — User I/O pin |
| ピン 97 | I/O — User I/O pin |
| ピン 98 | I/O — User I/O pin |
| ピン 99 | I/O — User I/O pin |
| ピン 100 | I/O — User I/O pin |
| ピン 101 | VCCINT — Core supply 5.0 V |
| ピン 102 | I/O — User I/O pin |
| ピン 103 | I/O — User I/O pin |
| ピン 104 | I/O — User I/O pin |
| ピン 105 | I/O — User I/O pin |
| ピン 106 | I/O — User I/O pin |
| ピン 107 | I/O — User I/O pin |
| ピン 108 | GND — Ground |
| ピン 109 | I/O — User I/O pin |
| ピン 110 | I/O — User I/O pin |
| ピン 111 | I/O — User I/O pin |
| ピン 112 | I/O — User I/O pin |
| ピン 113 | I/O — User I/O pin |
| ピン 114 | I/O — User I/O pin |
| ピン 115 | VCCIO — I/O supply (3.3 V or 5.0 V) |
| ピン 116 | I/O — User I/O pin |
| ピン 117 | I/O — User I/O pin |
| ピン 118 | I/O — User I/O pin |
| ピン 119 | I/O — User I/O pin |
| ピン 120 | I/O — User I/O pin |
| ピン 121 | I/O — User I/O pin |
| ピン 122 | GND — Ground |
| ピン 123 | I/O — User I/O pin |
| ピン 124 | I/O — User I/O pin |
| ピン 125 | I/O — User I/O pin |
| ピン 126 | I/O — User I/O pin |
| ピン 127 | I/O — User I/O pin |
| ピン 128 | I/O — User I/O pin |
| ピン 129 | I/O — User I/O pin |
| ピン 130 | VCCINT — Core supply 5.0 V |
| ピン 131 | TDI — JTAG test data in |
| ピン 132 | TRST — JTAG test reset |
| ピン 133 | TMS — JTAG test mode select |
| ピン 134 | TCK — JTAG test clock |
| ピン 135 | TDO — JTAG test data out |
| ピン 136 | nSTATUS — Configuration status (open-drain) |
| ピン 137 | nCONFIG — Configuration control (active-low) |
| ピン 138 | DCLK — Configuration clock input |
| ピン 139 | DATA0 — Configuration data input |
| ピン 140 | CONF_DONE — Configuration complete (open-drain) |
| ピン 141 | MSEL0 — Configuration mode select 0 |
| ピン 142 | MSEL1 — Configuration mode select 1 |
| ピン 143 | GND — Ground |
| ピン 144 | VCCINT — Core supply 5.0 V |
主な用途
EPF6016TI144-3N の用途: 6 件s: Telecom Line-Card Glue Logic, Industrial Control Boards, PCI / ISA Bus Bridges, Custom Peripheral Controllers, Prototype Gate-Array Emulation, Mixed-Voltage Legacy Board Designs.
Telecom Line-Card Glue Logic
The EPF6016TI144-3N fits telecom line-card glue-logic roles because its 117 user I/O and 1,320 logic elements provide enough capacity to bridge backplane buses, fan-out interrupts, and perform protocol conversion on legacy TDM cards. The 5.0 V core with MultiVolt I/O lets designers mix 3.3 V and 5.0 V peripherals on the same card without level translators, and the 125 MHz internal frequency easily meets typical TDM/E1 timing margins. The 144-LQFP footprint is hand-rework-friendly for field service. Trade-off: the SRAM fabric loses configuration at power-down, so a configuration EPROM (EPC1/EPC2) must be co-located on every line card.
おすすめ
Industrial Control Boards
The EPF6016TI144-3N is widely deployed on industrial PLC and motion-control boards where deterministic 5.0 V logic interfaces are needed to drive optocouplers, 24 V I/O modules, and legacy 8255-style peripheral buses. The 0 °C to +85 °C industrial temperature rating and 132 LABs give designers enough logic to implement custom PID loops, encoder quadrature decoders, and timing-critical interrupt controllers. MultiVolt I/O allows direct connection to 3.3 V ADC/DAC front-ends without external buffers. The part is obsolete, so legacy boards must plan a Cyclone IV migration path while maintaining the same 144-LQFP PCB footprint for as long as inventory lasts.
おすすめ
PCI / ISA Bus Bridges
The EPF6016TI144-3N excels at legacy PCI / ISA bus-bridge roles where 117 user I/O are needed to fan out address, data, and control signals between the host bus and downstream peripherals. Its 5.0 V core is natively compatible with PCI 5.0 V signaling, and MultiVolt I/O lets it bridge to 3.3 V CardBus or MiniPCI peripherals on the same card. The SRAM-based fabric and JTAG support enable in-system bitstream updates for bug fixes and protocol updates. Trade-off: designers must budget for an EPC2 configuration EPROM and ensure the 5.0 V supply is well decoupled because the 0.42 µm CMOS process draws meaningful dynamic current at 33 MHz PCI frequencies.
おすすめ
Custom Peripheral Controllers
Engineers use the EPF6016TI144-3N as a custom peripheral controller in legacy printers, point-of-sale terminals, and medical instrumentation where the 16K-gate fabric implements state machines, FIFO glue, and protocol handlers without the cost of an ASIC. The 144-LQFP package is hand-solderable and easy to rework, while the 5.0 V tolerance matches the power rails still common in those systems. The -3 speed grade delivers tight timing closure for serial-protocol controllers, and MultiVolt I/O lets the part talk directly to 3.3 V sensors and ADCs. Migration note: the part is obsolete, so new designs should target Cyclone IV in a similar TQFP-144 footprint to preserve PCB layout.
おすすめ
Prototype Gate-Array Emulation
The EPF6016TI144-3N is a cost-effective gate-array emulation platform for prototyping 16K-gate ASIC designs before mask commitment. Designers map RTL to the 1,320 logic elements, exercise real I/O on the 117 user pins, and validate timing at the 125 MHz internal frequency before tape-out. The JTAG port supports rapid bitstream reload during iterative bring-up, and MultiVolt I/O lets prototype boards mix legacy and modern voltage domains. The 144-LQFP package fits on a daughter-card alongside logic analyzers and scope probes for clean debug access. Caveat: SRAM-based fabric is volatile, so a configuration EPROM must be co-resident on every prototype card.
おすすめ
Mixed-Voltage Legacy Board Designs
The EPF6016TI144-3N supports mixed 3.3 V / 5.0 V board designs through its MultiVolt I/O feature, where the VCCIO rail can be set independently to 3.3 V or 5.0 V while VCCINT remains at 5.0 V. This is ideal for legacy systems that retain 5.0 V microcontrollers, SRAM, and bus transceivers while adding modern 3.3 V ADC/DAC/USB peripherals. The 117 user I/O can be partitioned between the two voltage domains on a per-bank basis, eliminating external level shifters and reducing BOM cost. The 132 LABs also let designers integrate the glue logic that was previously scattered across 74HCxx and 74LVCxx buffers, simplifying the board further.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: EPF6016TI144-3N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | EPF6016TI144-2N | EPF6016ATI144-3N | EPF6016ATI144-3 | EPF6016ATI144-2N | EPF6016ATI144-2 | EPF6016TI144-3 |
|---|---|---|---|---|---|---|---|
| Package | 144-LQFP (TQFP) | 144-LQFP (TQFP) - same | 144-LQFP (TQFP) - same | 144-LQFP (TQFP) - same | 144-LQFP (TQFP) - same | 144-LQFP (TQFP) - same | 144-LQFP (TQFP) - same |
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Usable Gates | 16,000 | 16,000 | 16,000 | 16,000 | 16,000 | 16,000 | 16,000 |
| Logic Elements | 1,320 | 1,320 | 1,320 | 1,320 | 1,320 | 1,320 | 1,320 |
| Speed Grade | -3 (faster) | -2 (slower) | -3 (faster) | -3 (faster) | -2 (slower) | -2 (slower) | -3 (faster) |
| Temperature Grade | Industrial (0C to +85C) | Industrial (0C to +85C) | Automotive (-40C to +125C) | Automotive (-40C to +125C) | Automotive (-40C to +125C) | Automotive (-40C to +125C) | Commercial (0C to +70C) |
| Core Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
主な差別化要因
- Industrial temperature bin with -3 speed grade （vs EPF6016TI144-3 (commercial temp, -3 speed))
- Highest Fmax in the FLEX 6016 TQFP-144 family （vs EPF6016TI144-2N)
- 117 user I/O out of 144 pins （vs EPF6010ATC144-3 (FLEX 10K10, same TQFP-144))
設計ノート
The EPF6016TI144-3N requires a stable 5.0 V core supply on every VCCINT pin (typically pins 8, 43, 72, 101, 130, 144 on the TQFP-144) plus a separate VCCIO rail (typically pins 28, 57, 86, 115) that can be tied to 3.3 V or 5.0 V. Decouple each VCCINT pin with a 0.1 µF ceramic cap placed within 5 mm of the pin, and add a bulk 10 µF tantalum or ceramic near the package. Estimated: at 100% toggle activity at 33 MHz on a PCI bus design, total current draw is roughly 100-150 mA on VCCINT plus 20-50 mA on VCCIO depending on loading.
The 144-LQFP package has 0.5 mm pitch gull-wing leads and a 20 mm body, so PCB layout must use 0.15 mm/0.20 mm trace-and-space rules and vias-in-pad or via-tented fan-out under the body. Estimated: 4 layers are recommended (top signal, inner ground, inner VCC, bottom signal) with a continuous ground plane beneath the device to control the 0.42 µm CMOS process's switching noise. Keep configuration EPROM (EPC1/EPC2) within 50 mm of the FPGA's DATA0/DCLK pins to avoid signal-integrity issues at 33 MHz configuration rates.
Common pitfalls when designing with the EPF6016TI144-3N include (1) forgetting the configuration EPROM because SRAM-based FPGAs lose their bitstream at every power-down, (2) leaving JTAG pins floating which can cause spurious configuration triggers, (3) mixing 3.3 V and 5.0 V signals on a single VCCIO bank which will damage the 5.0 V-tolerance I/O cells, and (4) omitting the nCONFIG pull-up resistor which prevents reliable reconfiguration. Always strap MSEL pins for the correct configuration mode (typically MSEL1=0, MSEL0=0 for serial EPROM configuration) before power-up.
コンプライアンス情報
RoHS / REACH / lead-free / halogen-free status was not present in the verified distributor data and is marked [DATA_NEEDED]. The FLEX 6000 family predates widespread RoHS adoption, so many original parts are non-RoHS; engineers should confirm with the distributor before assuming compliance.
