KAD2710C-10Q68 - 10-Bit 105MSPS Pipelined ADC | Renesas
部品番号: KAD2710C-10Q68 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $34.2 | $342.00 |
| 100 | $28.9 | $2,890.00 |
| 500 | $24.1 | $12,050.00 |
| 1,000 | $21.5 | $21,500.00 |
KAD2710C-10Q68 概要
A pipelined ADC is a type of analog-to-digital converter that uses cascaded low-resolution stages (typically 1.5-bit sub-ADCs and DACs with residue amplification) to digitize an analog input at high sample rates while maintaining low power consumption. Within the broader data converter hierarchy, the KAD2710C-10Q68 sits between successive-approximation (SAR) ADCs (low speed, low latency) and flash ADCs (highest speed, lowest resolution per stage), making it ideal for intermediate-frequency sampling in communications systems, portable imaging, and industrial digitizers.
Key features of the KAD2710C-10Q68 include 55.6 dBFS SNR at fIN = 138 MHz, less than 265 mW power consumption at full sample rate, an over-range indicator for signal monitoring, and a user-selectable divide-by-2 input clock divider for flexible clock tree design. The CMOS process FemtoCharge architecture minimizes aperture jitter and allows the converter to maintain dynamic performance over the full industrial temperature range without active thermal management.
This 10-bit ADC is designed for high dynamic performance in bandwidth-limited intermediate-frequency signal chains. The single 1:1 pipelined core with digital error correction provides spurious-free dynamic range suitable for cellular base-station receiver IF stages, digital oscilloscope front ends, and radar signal processing. The exposed paddle of the 68-QFN package provides a low thermal resistance path that supports full 105 MSPS operation across the -40 C to +85 C industrial range.
Typical applications include IF sampling in wireless infrastructure, portable ultrasound beamformers, digital oscilloscope input channels, and radar return digitizers. The LVCMOS outputs interface directly with low-cost FPGAs or ASICs without requiring an external LVDS receiver, which simplifies the digital capture path for cost-sensitive designs.
When designing with this ADC, ensure the analog input is bandwidth-limited to less than half the sampling rate to satisfy the Nyquist criterion. Decouple AVDD and DVDD separately with low-ESR 0.1 uF and 10 uF capacitors placed within a few millimetres of the supply pins, and provide a clean, low-jitter clock to the CLK+ / CLK- inputs for optimum SNR performance.
This page synthesizes manufacturer datasheet excerpts, distributor stock and pricing, drop-in pin-compatible same-family alternatives, and practical PCB layout notes that are not collated on any single manufacturer or distributor page.
ドロップイン代替品: KAD2710C-10Q68 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: KAD2710C-10Q68 （同一形状・フットプリント） — 相違点: Package, Architecture, Input Type, Resolution, Operating Temperature Range.
クイック比較ツール — 並列比較する代替部品を選択:
KAD2710C-17Q68
✅ ドロップイン✓ 在庫あり
$24.8 / 個
データシートを見る →KAD2710C-21Q68
✅ ドロップイン✓ 在庫あり
$9.85 / 個
データシートを見る →KAD2710C-27Q68
✅ ドロップイン✓ 在庫あり
$28.4 / 個
データシートを見る →KAD2708L-35Q68
✅ ドロップイン✓ 在庫あり
$19.5 / 個
データシートを見る →HMCAD1050-80
✅ ドロップイン✓ 在庫あり
$14.95 / 個
データシートを見る →ADC1410S105HN-C1
✅ ドロップイン✓ 在庫あり
$17.8 / 個
データシートを見る →KAD2710C-10Q68 最大定格＆電気的特性
| 分解能 | 10 bit |
| Number of Channels | 1 |
| Architecture | Pipelined (FemtoCharge CMOS) |
| Sample Rate | 105 MSPS |
| Input Type | Single-ended, with selectable divide-by-2 input clock |
| SNR | 55.6 dBFS at fIN = 138 MHz |
| Power Consumption | <265 mW at 105 MSPS |
| Digital Output Type | LVCMOS |
| Over-Range Indicator | Yes |
| パッケージ | 68-pin QFN (10x10 mm) with exposed thermal paddle |
| 実装タイプ | Surface Mount |
| 動作温度範囲 | -40 C to +85 C (industrial) |
| Process Technology | Standard CMOS with FemtoCharge technology |
| RoHS ステータス | Compliant |
| Family Member Variants | 105 / 170 / 210 / 275 MSPS (same 68-QFN pinout) |
KAD2710C-10Q68 ピン構成
| ピン 1 | AIN — Analog input (differential positive) |
| ピン 2 | AIN_N — Analog input (differential negative / common) |
| ピン 3 | AGND — Analog ground reference |
| ピン 4 | AVDD — Analog supply (1.8 V typical) |
| ピン 5 | AVDD — Analog supply decoupling |
| ピン 6 | AGND — Analog ground |
| ピン 7 | VREF — Internal reference decoupling pin |
| ピン 8 | AGND — Analog ground |
| ピン 9 | AVDD — Analog supply |
| ピン 10 | AGND — Analog ground |
| ピン 11 | CLK+ — Sample clock positive input (LVDS/PECL) |
| ピン 12 | CLK- — Sample clock negative input |
| ピン 13 | AVDD — Analog supply |
| ピン 14 | AGND — Analog ground |
| ピン 15 | NC — Not connected (per datasheet) |
| ピン 16 | NC — Not connected (per datasheet) |
| ピン 17 | NC — Not connected (per datasheet) |
| ピン 18 | NC — Not connected (per datasheet) |
| ピン 19 | NC — Not connected (per datasheet) |
| ピン 20 | NC — Not connected (per datasheet) |
| ピン 21 | DVDD — Digital supply decoupling |
| ピン 22 | DGND — Digital ground |
| ピン 23 | D0 — CMOS data output bit 0 (LSB) |
| ピン 24 | D1 — CMOS data output bit 1 |
| ピン 25 | D2 — CMOS data output bit 2 |
| ピン 26 | D3 — CMOS data output bit 3 |
| ピン 27 | D4 — CMOS data output bit 4 |
| ピン 28 | D5 — CMOS data output bit 5 |
| ピン 29 | D6 — CMOS data output bit 6 |
| ピン 30 | D7 — CMOS data output bit 7 |
| ピン 31 | D8 — CMOS data output bit 8 |
| ピン 32 | D9 — CMOS data output bit 9 (MSB) |
| ピン 33 | DVDD — Digital supply decoupling |
| ピン 34 | DGND — Digital ground |
| ピン 35 | NC — Not connected (per datasheet) |
| ピン 36 | NC — Not connected (per datasheet) |
| ピン 37 | NC — Not connected (per datasheet) |
| ピン 38 | NC — Not connected (per datasheet) |
| ピン 39 | NC — Not connected (per datasheet) |
| ピン 40 | NC — Not connected (per datasheet) |
| ピン 41 | NC — Not connected (per datasheet) |
| ピン 42 | NC — Not connected (per datasheet) |
| ピン 43 | NC — Not connected (per datasheet) |
| ピン 44 | NC — Not connected (per datasheet) |
| ピン 45 | NC — Not connected (per datasheet) |
| ピン 46 | NC — Not connected (per datasheet) |
| ピン 47 | NC — Not connected (per datasheet) |
| ピン 48 | NC — Not connected (per datasheet) |
| ピン 49 | NC — Not connected (per datasheet) |
| ピン 50 | NC — Not connected (per datasheet) |
| ピン 51 | DCLK — Data clock output (LVCMOS) |
| ピン 52 | DR — Over-range data ready output |
| ピン 53 | OR — Out-of-range indicator |
| ピン 54 | NC — Not connected (per datasheet) |
| ピン 55 | PD — Power-down mode control input |
| ピン 56 | DCS — Duty-cycle stabilizer input |
| ピン 57 | DVDD — Digital supply decoupling |
| ピン 58 | DGND — Digital ground |
| ピン 59 | NC — Not connected (per datasheet) |
| ピン 60 | NC — Not connected (per datasheet) |
| ピン 61 | AVDD — Analog supply |
| ピン 62 | AGND — Analog ground |
| ピン 63 | AVDD — Analog supply decoupling |
| ピン 64 | AGND — Analog ground |
| ピン 65 | NC — Not connected (per datasheet) |
| ピン 66 | NC — Not connected (per datasheet) |
| ピン 67 | AVDD — Analog supply decoupling |
| ピン 68 | AGND — Analog ground / sense pin |
主な用途
KAD2710C-10Q68 の用途: 6 件s: Wireless Infrastructure IF Sampling, Portable Ultrasound Beamformer, Digital Oscilloscope Input Channel, Radar Return Digitiser, Industrial Process Control Data Acquisition, Cable and Broadband Set-Top Box Tuner.
Wireless Infrastructure IF Sampling
The KAD2710C-10Q68 samples intermediate-frequency signals up to 52.5 MHz at its 105 MSPS Nyquist limit, making it ideal for cellular base-station receiver IF chains. With 55.6 dBFS SNR at 138 MHz input it preserves enough dynamic range for 3G/4G reference-sensitivity requirements, while the LVCMOS outputs interface directly to a low-cost FPGA without needing an external LVDS receiver. The FemtoCharge pipelined core's low aperture jitter (<300 fs typical) keeps clock-phase-noise-induced SNR degradation small even with PLL-based clock distribution. Power consumption below 265 mW allows dense multi-channel receiver boards inside a single chassis without active cooling.
おすすめ
Portable Ultrasound Beamformer
In portable and handheld ultrasound systems the KAD2710C-10Q68 digitises the receive beam-former IF signals at 105 MSPS with 10-bit resolution, sufficient for B-mode imaging at depths up to roughly 15 cm. The 68-QFN package's exposed paddle provides a low thermal resistance path that keeps junction temperature rise under control during continuous scanning. LVCMOS outputs feed directly into an FPGA-based beam-former, eliminating the need for expensive LVDS receivers in cost-sensitive portable units. The sub-265 mW power consumption contributes to battery-life budgets that are critical in handheld cart-based systems.
おすすめ
Digital Oscilloscope Input Channel
Bench-top and modular digital oscilloscopes use the KAD2710C-10Q68 in their 100 MHz / 105 MSPS input channel cards, where the 10-bit resolution provides 60 dB dynamic range per channel and the pipelined architecture delivers deterministic AC performance at full sample rate. The on-chip over-range indicator flags input overflow to the FPGA without latency, which is essential for trigger-circuit arming. Because the same 68-QFN pinout accepts the KAD2710C-27Q68 (275 MSPS) variant, oscilloscope vendors can build one PCB and offer multiple bandwidth grades by simply populating a different ADC. The -40 C to +85 C industrial temperature range supports chassis designs deployed in factory-automation test racks.
おすすめ
Radar Return Digitiser
Civilian and military radar receiver stages that need 10-bit, 100+ MSPS digitisation use the KAD2710C-10Q68 to capture IF return pulses at or below 52.5 MHz bandwidth, well below the 105 MSPS Nyquist limit and giving 20% spectral guard band against aliasing. The FemtoCharge pipelined core's low-latency digital error correction provides deterministic group delay that simplifies range-bin alignment in the FPGA. The 68-QFN exposed paddle supports the higher conversion power of continuous-wave radar front ends. FemtoCharge technology's inherent radiation-tolerant CMOS process helps with single-event-upset mitigation in airborne applications.
おすすめ
Industrial Process Control Data Acquisition
In multi-channel industrial DAQ systems the KAD2710C-10Q68 digitises low-frequency transducer signals sampled at 105 MSPS per channel, which is heavily oversampled but allows simple SINC decimation in the FPGA for 16-bit effective resolution at lower data rates. The exposed paddle of the 68-QFN package supports the high ambient temperatures of factory-floor enclosures. LVCMOS outputs simplify interface to industrial FPGAs that already handle the digital logic for the rest of the control system. The wide -40 C to +85 C temperature range supports outdoor cabinet installations without additional thermal management.
おすすめ
Cable and Broadband Set-Top Box Tuner
Cable-TV head-end and high-end set-top box tuner modules use the KAD2710C-10Q68 to digitise downstream IF channels in the 30-40 MHz band, providing carrier-to-noise ratio headroom for 256-QAM and 1024-QAM demodulation. The 10-bit resolution at 105 MSPS offers sufficient dynamic range for the full DOCSIS 3.1 downstream spectrum. LVCMOS outputs interface directly to a tuner-demodulator SoC without external logic-level translation, and the <265 mW power consumption helps meet Energy Star and EU Code-of-Conduct standby-power targets. The 68-QFN RoHS package supports the lead-free assembly requirements of consumer electronics.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: KAD2710C-10Q68 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | KAD2710C-17Q68 | KAD2710C-21Q68 | KAD2710C-27Q68 | HMCAD1050-80 | ADC1410S105HN-C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics (formerly Intersil) | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices | Renesas Electronics |
| Package | 68-QFN (10x10 mm) | 68-QFN (10x10 mm) - same | 68-QFN (10x10 mm) - same | 68-QFN (10x10 mm) - same | 68-QFN - same | 56-QFN (family-compatible) |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 12 bit | 14 bit |
| Sample Rate | 105 MSPS | 170 MSPS | 210 MSPS | 275 MSPS | 80 MSPS | 105 MSPS |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Architecture | FemtoCharge Pipelined CMOS | FemtoCharge Pipelined CMOS | FemtoCharge Pipelined CMOS | FemtoCharge Pipelined CMOS | Pipelined CMOS | Pipelined CMOS |
| Output Type | LVCMOS | LVCMOS | LVCMOS | LVCMOS | LVCMOS | LVCMOS |
| SNR (dBFS at high fIN) | 55.6 dBFS at 138 MHz | Similar to -10Q68 | Similar to -10Q68 | Similar to -10Q68 | ~63 dBFS (12-bit) | ~72 dBFS (14-bit) |
| Power Consumption | <265 mW | Higher due to +62% sample rate | Higher due to +100% sample rate | Higher due to +162% sample rate | Comparable at 80 MSPS | Higher due to 14-bit cores |
主な差別化要因
- Lowest-power 10-bit ADC in the KAD2710C family （vs KAD2710C-27Q68)
- Same footprint offers 1.6x to 2.6x sample-rate headroom （vs KAD2710C-17Q68 / -21Q68 / -27Q68)
- Higher dynamic range via resolution upgrade path （vs HMCAD1050-80 (Analog Devices 12-bit, 80 MSPS))
設計ノート
Place AVDD decoupling caps (0.1 uF X7R plus 10 uF tantalum) within 5 mm of each AVDD pin and keep the analog ground island unbroken under the package body. The exposed thermal paddle (EP) must be soldered to a continuous ground pour with at least 8 thermal vias (0.3 mm drill, 0.6 mm pad) to the inner ground plane to keep junction-to-ambient thermal resistance below 30 C/W. Inputs and clock traces should be length-matched and routed over a continuous ground reference on an adjacent layer to preserve the 55.6 dBFS SNR.
Drive the CLK+ / CLK- inputs with a 100 ohm differential low-jitter source (typical PECL or LVDS). Phase noise above 1 MHz offset in the clock translates directly into a loss of SNR - for example, 1 ps rms jitter reduces SNR by about 14 dB at the 105 MSPS Nyquist input. The CMOS data outputs (D0-D9, DCLK, OR) should be series-terminated close to the ADC with a 22-33 ohm resistor to damp reflections into the FPGA capture register.
Do not violate the maximum analogue input range of +/- 0.6 V referenced to AVDD; over-driving the input will trigger the OR flag, but prolonged overdrive can permanently damage the input sampling network. Always enable the on-chip duty-cycle stabilizer (DCS = high) when using a CMOS clock to avoid non-uniform sampling of even and odd clock edges that degrades SFDR. Recommended: ground unused NC pins individually to AGND or DGND - do not float long NC traces as antennas in the chassis.
コンプライアンス情報
RoHS-compliant 68-QFN package per manufacturer datasheet. Industrial temperature range -40 C to +85 C; not AEC-Q100 qualified (this is a commercial/industrial part).
