KSZ8851-16MLLJ - 10/100 Ethernet Controller | Microchip
部品番号: KSZ8851-16MLLJ ✓ 生産中KSZ8851-16MLLJ 概要
An Ethernet MAC controller is an interface IC that manages packet transmission, reception, addressing, and host-bus transactions, while a Base-T/TX PHY provides the physical-layer connection to twisted-pair Ethernet. Together, the MAC and PHY form a complete single-port Ethernet endpoint for embedded processors, industrial controllers, test equipment, and connected products.
The KSZ8851 family supports configurable generic processor interfaces. The 16-bit MLLJ configuration provides an 8-bit or 16-bit non-PCI host interface, allowing the controller to connect with embedded processors that use parallel buses rather than SPI or PCI Express. The controller also uses dynamic memory pointers for efficient descriptor-based packet management.
The integrated MAC, PHY, and host interface consolidate several Ethernet functions into one package. This can reduce external component count and simplify the board-level connection between the processor and RJ45 network interface. The 48-LQFP package has exposed leads suitable for conventional surface-mount assembly and inspection.
Typical applications include industrial automation, factory equipment, building controls, embedded instrumentation, serial-to-Ethernet gateways, print servers, and embedded network appliances. The device is particularly appropriate when a system needs a deterministic parallel host connection and a conventional 10/100 Ethernet network rather than a higher-speed multi-gigabit interface.
Designers should use the manufacturer pin-description table when assigning processor signals, PHY connections, clocks, reset inputs, and decoupling networks. Magnetics and connector selection must be matched to the Ethernet application, while the host bus must support the selected 8-bit or 16-bit operating mode and required address and data timing.
This page organizes the manufacturer product information, package details, datasheet links, interface alternatives, and practical implementation guidance. It is intended to help engineers identify whether the KSZ8851-16MLLJ matches the required Ethernet speed, parallel bus architecture, package, temperature class, and embedded-system application.
ドロップイン代替品: KSZ8851-16MLLJ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: KSZ8851-16MLLJ (同一形状・フットプリント) — 相違点: AEC-Q100 Qualification, Device Type, Ethernet Speed, Host Interface, Package.
KSZ8851-16MLLI
✅ ドロップイン価格はお問い合わせください
データシートを見る →KSZ8851-16MLLU-TR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
KSZ8851-16MLL
✅ ドロップイン📋 参考代替品(カタログ未掲載)
KSZ8851-16MLL-TR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
KSZ8851-16MLLJ 仕様
| Device Type | Single-port Ethernet MAC controller with integrated PHY |
| Ethernet Speed | 10/100 Mb/s |
| Physical Layer | 10/100 Base-T/TX PHY |
| Host Interface | 8-bit or 16-bit generic non-PCI parallel interface |
| Memory Interface | Dynamic memory pointer |
| パッケージ | 48-LQFP (7 mm x 7 mm) |
| Lead-Free Package Option | 48-pin lead-free LQFP |
| 実装タイプ | Surface Mount |
| 動作温度 | -40°C to +125°C |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
KSZ8851-16MLLJ 48-pin lead-free lqfp ピン配置ガイド
KSZ8851-16MLLJ (48-pin lead-free lqfp パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: KSZ8851-16MLLJ.
詳細は データシート をご参照ください。
主な用途
KSZ8851-16MLLJ の用途: 6 件s: Industrial Automation Controller, Building Control Gateway, Embedded Instrumentation, Print Server, Factory Sensor Gateway, Network Appliance with Legacy CPU.
Industrial Automation Controller
The KSZ8851-16MLLJ fits industrial automation equipment that needs a single 10/100 Mb/s Ethernet connection and a parallel embedded-processor interface. Its 8-bit or 16-bit non-PCI bus avoids requiring a PCI Express interface in the host controller, while the integrated Base-T/TX PHY reduces the number of separate network-interface components. The documented -40°C to +125°C operating range supports industrial environments with significant enclosure temperature variation. Place the device between the processor bus and Ethernet magnetics, and confirm the data sheet's address mode, bus timing, reset requirements, and interrupt signals during hardware design.
おすすめ
Building Control Gateway
The KSZ8851-16MLLJ is suitable for a building-control gateway that bridges a legacy embedded processor to 10/100 Mb/s Ethernet. The controller's generic 8-bit or 16-bit parallel interface can share a straightforward bus arrangement with sensors, actuators, and local I/O, while the integrated MAC and PHY provide one complete network endpoint. Its -40°C to +125°C range accommodates equipment installed near heat-producing power stages. The design must still provide the required Ethernet magnetics, connector, isolation policy, reference clock, and decoupling network specified by the manufacturer data sheet.
おすすめ
Embedded Instrumentation
The KSZ8851-16MLLJ can add networked data transfer to embedded instrumentation without requiring a host processor with a PCI Express interface. Its 10/100 Mb/s operation is appropriate for supervisory data, configuration transfer, and status reporting, while the 48-LQFP package supports conventional surface-mount assembly. The 8-bit or 16-bit interface width provides design flexibility for processors with limited external I/O. Engineers should use the manufacturer timing information to select the operating mode, include required clock and reset circuitry, and verify that the Ethernet connection complies with the installation's isolation requirements.
おすすめ
Print Server
The KSZ8851-16MLLJ is appropriate for a print server or print-to-Ethernet adapter built around a legacy embedded processor. A single-port 10/100 Mb/s link provides sufficient bandwidth for many print paths, and the generic parallel host interface allows the controller to operate without a dedicated PCI Express interface. The integrated Base-T/TX PHY simplifies the network side of the design, while the 48-LQFP footprint remains manageable for compact industrial electronics. Productization still requires correct Ethernet magnetic coupling, surge protection, firmware-driven descriptor handling, and host-bus timing checks.
おすすめ
Factory Sensor Gateway
The KSZ8851-16MLLJ can provide an Ethernet uplink for a factory sensor gateway that aggregates local measurements before forwarding them to supervisory equipment. The 10/100 Mb/s rate is well matched to typical sensor and status traffic, and the 8-bit or 16-bit non-PCI interface suits small processors that need deterministic access to packet descriptors and interrupt-driven status. Its extended 125°C upper operating temperature is valuable in compact gateways mounted near industrial heat sources. Use the manufacturer guidance for clocking, PHY termination, magnetic components, and power-supply sequencing to preserve network performance.
おすすめ
Network Appliance with Legacy CPU
The KSZ8851-16MLLJ gives a legacy embedded CPU a cost-effective 10/100 Mb/s Ethernet connection through a generic parallel bus. It is useful for protocol gateways, serial-to-Ethernet products, and compact network appliances that lack PCI Express but can support an 8-bit or 16-bit non-PCI interface. Integrating the MAC and PHY reduces board complexity compared with separating the host-facing MAC from the physical layer. The design should account for packet-memory organization, interrupt latency, host bus access time, and Ethernet transformer requirements. The manufacturer evaluation-board documentation provides a practical starting point for the 48-LQFP implementation.
おすすめ
エンジニアリング参考データ: KSZ8851-16MLLJ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | KSZ8851-16MLLI | KSZ8851-16MLLU-TR | KSZ8851-16MLL | KSZ8851-16MLL-TR |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-LQFP (7 mm x 7 mm) | 48-LQFP (7 mm x 7 mm) | 48-LQFP (7 mm x 7 mm) | 48-LQFP (7 mm x 7 mm) | 48-LQFP (7 mm x 7 mm) |
| Device Function | Single-port 10/100 Ethernet MAC controller with integrated PHY | Single-port 10/100 Ethernet MAC controller with integrated PHY | KSZ8851-16MLL family Ethernet controller | Single-port 10/100 Ethernet MAC controller with integrated PHY | Single-port 10/100 Ethernet MAC controller with integrated PHY |
| Ethernet Speed | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s | 10/100 Mb/s |
| Host Interface | 8-bit or 16-bit generic non-PCI parallel interface | 8-bit or 16-bit generic non-PCI parallel interface | 8-bit or 16-bit generic non-PCI parallel interface | 8-bit or 16-bit generic non-PCI parallel interface | 8-bit or 16-bit generic non-PCI parallel interface |
| Physical Layer | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY | 10/100 Base-T/TX PHY |
| Package Lead Configuration | 48-pin lead-free LQFP | 48-pin LQFP | 48-pin LQFP | 48-pin lead-free LQFP | 48-pin lead-free LQFP |
主な差別化要因
- Higher documented upper operating temperature (vs KSZ8851-16MLLI)
- Complete 10/100 Ethernet endpoint in one controller package (vs KSZ8851-16MLLU-TR)
- Flexible parallel host integration (vs KSZ8851-16MLL)
- Industrial temperature capability with an extended upper limit (vs KSZ8851-16MLL-TR)
設計ノート
Use the manufacturer KSZ8851-16MLL evaluation-board layout as the primary placement reference for the 48-LQFP device. Keep the host-bus traces short, route clock and reset signals away from Ethernet and switching-node circuitry, and place the required bypass capacitors close to their associated supply pins. The parallel bus should be laid out with continuous reference planes where practical, while Ethernet traces should follow the layout and isolation guidance in the manufacturer data sheet.
The host interface can operate in 8-bit or 16-bit modes, so processor data, address, control, and interrupt signals must be assigned according to the selected configuration. Check propagation delay, bus timing, address mapping, and interrupt polarity in the data sheet rather than treating the interface as a fixed-width bus. Firmware should also configure the controller's memory-pointer and FIFO behavior before packets are transferred.
Design the Ethernet physical layer with the network magnetics, connector, protection network, and PHY traces as a controlled subsystem. Follow the manufacturer's recommended component placement and trace geometry, keep the connector interface away from sensitive analog or high-speed clock circuitry, and provide the specified isolation between external cable circuitry and the host side. Do not infer the Ethernet connection details from the digital host-bus schematic alone.
A 48-LQFP footprint alone does not guarantee a valid substitution. Before replacing KSZ8851-16MLLJ with KSZ8851-16MLLI, verify the operating-temperature ceiling, supply configuration, ordering suffix, and approved package form. MLLI is documented for -40°C to +85°C, whereas MLLJ is documented for -40°C to +125°C; substituting the wrong grade can reduce environmental margin even when the pins and Ethernet function appear unchanged.
コンプライアンス情報
The manufacturer evaluation-board user guide identifies a 48-pin lead-free LQFP implementation. RoHS is reported for the related KSZ8851-16MLLI variant, but the exact KSZ8851-16MLLJ compliance declarations are not stated in the cited product records.