LC4128B-5T100I - 128-Macro-Cell ispMACH 4000B CPLD, 227 MHz | Lattice
部品番号: LC4128B-5T100I ✓ 生産中LC4128B-5T100I 概要
A CPLD is a user-programmable logic device that stores its configuration in non-volatile internal flash memory. Physically, a CPLD sits between simple programmable logic arrays and FPGAs: it offers the deterministic, single-chip, non-volatile configuration of a PAL or GAL while delivering the macro-cell density, wide I/O and multi-clock routing that previously required masked-programmed mask ROMs or gate arrays. The ispMACH 4000B name identifies Lattice's high-density SuperFAST branch of that family, aimed at glue logic, bus arbitration, protocol conversion and control-plane designs rather than datapath DSP.
Key features include 128 macro cells that can be interconnected with a fast global interconnect, 64 dedicated user I/O pins at 3.3 V / 2.5 V / 1.8 V, JTAG-based in-system programming for board-level configuration, and four programmable global clock pins. Because the configuration is stored in flash, the LC4128B-5T100I powers up in its logic state with no external PROM, no bitstream load time and no dedicated configuration FPGA on the board.
Architecturally, each macro cell contains programmable AND/OR logic, flip-flops, control logic and dedicated interconnect resources, so multi-clock designs with registered outputs are built without external registers. The 100-pin TQFP package exposes 64 user I/O plus dedicated configuration and control pins, giving a moderate pin count that suits moderate- to high-complexity interface logic rather than ultra-dense multi-bank designs.
Typical applications include bus arbitration and address decode for legacy peripherals, parallel-to-serial protocol bridging, motor and stepper control sequencing, test fixture and instrument control logic, encryption and key-management control, and glue logic that isolates an older microprocessor from a newer fabric. Designs that need more logic density or true DSP blocks typically move to an FPGA, while designs needing only a handful of gates move to a smaller GAL.
The main design consideration is that the LC4128B-5T100I is a mature, flash-based part with fixed, non-expandable resources: 128 macro cells must cover the entire design, including any glue logic added during debug. Confirm the -5 speed grade against your clock budget, keep JTAG access for in-field reprogramming, and observe the decoupling and thermal layout guidance in the family datasheet when running at 3.3 V with maximum I/O switching.
This page consolidates the device specification, package details, drop-in alternatives from the same Lattice ispMACH 4000B family, and practical design guidance that engineers would otherwise have to piece together from the manufacturer datasheet and distributor listings.
ドロップイン代替品: LC4128B-5T100I — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
LC4128B-5TN100I
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LC4128B-5T100C
✅ ドロップイン価格はお問い合わせください
データシートを見る →LC4128B-5TN100C
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LC4128B-5T100I 最大定格&電気的特性
| Device Type | In-System Programmable SuperFAST High Density PLD (CPLD) |
| Product Family | ispMACH 4000B |
| Macro Cells | 128 |
| User I/O Pins | 64 |
| Maximum Operating Frequency (fMAX) | 227 MHz |
| Maximum fMAX (per family feature list) | 380 MHz |
| Propagation Delay (tPD) | 2.5 ns |
| Logic Family | CMOS |
| 電源電圧 | 3.3 V / 2.5 V / 1.8 V |
| Package Type | TQFP-100 |
| Total Pin Count | 100 pins |
| Global Clock Pins | Up to 4, programmable |
| Configuration Memory | Non-volatile in-system programmable flash |
| Programming Interface | JTAG in-system programming |
| 実装タイプ | Surface Mount |
LC4128B-5T100I tqfp-100 ピン配置ガイド
LC4128B-5T100I (tqfp-100 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: LC4128B-5T100I.
詳細は データシート をご参照ください。
主な用途
LC4128B-5T100I の用途: 6 件s: Legacy Bus Arbitration and Address Decode, Industrial Motor and Stepper Sequencing, Test and Measurement Fixture Control, Data Acquisition Handshake and Filtering, Interface and Protocol Bridging, Programmable Logic for Small Form-Factor Modules.
Legacy Bus Arbitration and Address Decode
The LC4128B-5T100I is well suited to arbitration and address decoding between an older microprocessor and newer peripherals because its 128 macro cells can absorb decode logic, handshake state machines and bus turnaround logic on one chip. With 64 user I/O pins, a design can hold several chip-select lines, bus request/grant signals and data-bus slices without a second logic device. Operated at 3.3 V or 2.5 V to match the legacy bus, it delivers up to 227 MHz with a 2.5 ns propagation delay, which covers standard bus cycle times with margin. JTAG in-system programming means the same board can be re-decoded in the field if the peripheral map changes, and non-volatile flash configuration gives deterministic state immediately after power-up.
おすすめ
Industrial Motor and Stepper Sequencing
In motor and stepper control boards, the LC4128B-5T100I provides the deterministic sequencing logic, direction decoding and limit-switch conditioning that a microcontroller alone handles awkwardly. Its programmable global clock pins allow the step rate generator to run in its own clock domain while the position counter runs from a slower system clock, avoiding metastable crossings between unrelated domains. With 64 I/O pins, one device can drive step/direction pairs, enable lines and encoder index inputs. Supply operation at 3.3 V and 2.5 V aligns with industrial logic rails, while in-system programming via JTAG allows firmware-adjacent logic fixes without board rework in the field.
おすすめ
Test and Measurement Fixture Control
Instrument front-ends and ATE fixtures use the LC4128B-5T100I to generate stimulus patterns, control analog switch matrices and arbitrate between measurement channels. Because the device is non-volatile, a fixture board powers up in its known test configuration with no time-consuming bitstream download, which shortens test cycle time. The 64 user I/O pins are sufficient for instrument handshake, trigger routing and relay driver control, and the up-to-four programmable global clock pins let trigger and pattern clocks be divided independently. In-system JTAG programming also allows a single board to be reconfigured for different DUT test plans in a manufacturing cell without swapping hardware.
おすすめ
Data Acquisition Handshake and Filtering
The LC4128B-5T100I can serve as the timing hub between a fast ADC and a slower host processor in a data acquisition system, generating deterministic sample triggers, de-multiplexing control signals and filtering glitches on control lines. Registering the outputs through macro-cell flip-flops keeps trigger timing independent of host bus latency, and the programmable global clock pins support dividing a master sample clock for slower banks of channels. Running the logic at 2.5 V or 1.8 V next to modern converter cores reduces level-shifting components. Because configuration is held in internal flash, the acquisition board retains its sequencing program across power cycles and requires no external configuration memory.
おすすめ
Interface and Protocol Bridging
Where a board mixes two protocol families, the LC4128B-5T100I implements the glue that converts between them: parallel-to-serial shifting, byte stuffing, parity generation and clock-domain crossing. Macro-cell flip-flops provide the registered pipeline needed for source-synchronous handshakes, while the four programmable global clock pins support a slow management clock alongside a fast data clock. At 3.3 V the device can sit directly alongside legacy peripherals, and its 64 I/O pins fit a full 32-bit data bus plus control lines in a single TQFP-100 footprint. JTAG access lets a field technician reconfigure the bridge after a protocol revision without removing the board from the enclosure.
おすすめ
Programmable Logic for Small Form-Factor Modules
The LC4128B-5T100I is useful as a companion logic device on communication modules and IoT gateways, where a microcontroller lacks spare pins or timer resources. Its 128 macro cells can host sensor sampling control, watchdog logic, power sequencing and status multiplexing, and the 64 I/O pins allow direct drive of indicators, resets and level shifters. Multi-voltage support (3.3 V, 2.5 V and 1.8 V) lets the same CPLD interface to both a radio supply domain and a digital core domain, reducing level translators on crowded boards. Non-volatile in-system programming over JTAG means production programming and field upgrades happen through the same test interface, and the part powers up functional without any configuration load sequence.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LC4128B-5T100I — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LC4128B-5TN100I | LC4128B-5T100C | LC4128B-5TN100C |
|---|---|---|---|---|
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Macro Cells | 128 | 128 | 128 | 128 |
| User I/O Pins | 64 | 64 | 64 | 64 |
| Maximum Operating Frequency | 227 MHz | 227 MHz | 227 MHz | 227 MHz |
| Propagation Delay (tPD) | 2.5 ns | 2.5 ns | 2.5 ns | 2.5 ns |
| Supply Voltage Options | 3.3 V / 2.5 V / 1.8 V | 3.3 V / 2.5 V / 1.8 V | 3.3 V / 2.5 V / 1.8 V | 3.3 V / 2.5 V / 1.8 V |
| Global Clock Pins | Up to 4, programmable | Up to 4, programmable | Up to 4, programmable | Up to 4, programmable |
| Temperature Grade | -I industrial grade ordering designation | Industrial grade ordering designation | Commercial grade | Commercial grade |
| Configuration Memory | Non-volatile in-system programmable flash | Non-volatile in-system programmable flash | Non-volatile in-system programmable flash | Non-volatile in-system programmable flash |
主な差別化要因
- Non-volatile in-system programmable configuration removes the external PROM (vs LC4128B-5T100C)
- 128 macro cells and 64 user I/O in a single TQFP-100 footprint (vs LC4128B-5TN100I)
- Multi-voltage operation in one package footprint (vs LC4128B-5TN100C)
設計ノート
Do not treat the ispMACH 4000B macro-cell count as expandable: the 128 macro cells of the LC4128B-5T100I must cover the entire design, including glue logic added during bring-up. Report macro-cell usage from the Lattice ispMACH development tool at every revision, not just at release, because a design that fits at 95% utilisation on the first pass has no headroom for late fixes. If utilisation climbs above roughly 80%, plan the migration path to a larger ispMACH family or an FPGA before committing the PCB spin.
Follow the TQFP-100 land pattern and thermal pad connection shown in the Lattice ispMACH 4000B family data sheet, including the exposed pad tie and the recommended via array for heat spreading. Place decoupling capacitors on the VCC and VCCIO pins close to the package, with separate high-frequency ceramic bypass on each supply rail. Keep the JTAG chain (TCK, TMS, TDI, TDO) away from fast switching outputs and route it as a short, quiet path to the programming header so field updates stay reliable.
Multi-clock designs must assign each domain a dedicated global clock pin and register all cross-domain signals in flip-flops rather than routing them as combinational paths, since the ispMACH 4000B interconnect is not a synchronous design boundary. When driving external buses at 227 MHz, confirm the output-slew and load assumptions in the AC timing tables of the family data sheet, and account for board skew with series termination or a source-synchronous arrangement. Registered outputs are preferred over combinational outputs for any signal leaving the device.
コンプライアンス情報
No compliance declarations for the LC4128B-5T100I were found in the manufacturer or distributor documentation reviewed. The part is a commercial/industrial logic device and is not an AEC-Q100 automotive-qualified product. Confirm RoHS, REACH and lead-free status with the manufacturer before committing to a regulated end market.