LM2904VNG - Dual 30V Operational Amplifier | onsemi
部品番号: LM2904VNG ✓ 生産中LM2904VNG 概要
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while using external feedback to define the closed-loop gain. The dual configuration provides two amplifier channels in one package, making it useful for signal conditioning, buffering, filtering, transducers, instrumentation, and control applications. The LM2904VNG operates from a single supply or split supply, and its common-mode input voltage range extends to ground or VEE. This makes it appropriate for circuits that use low-voltage sensing or single-rail power arrangements where the input signal approaches the lower supply rail.
Key characteristics include two amplifier circuits, a general-purpose amplifier type, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, operation from 3 V to 32 V, and an 8-pin PDIP package. The package is specified as an 8-DIP measuring 0.300 inches, or 7.62 mm, in pitch. The component is identified as a tube-packaged part in the retrieved datasheet description, making it suitable for conventional through-hole PCB assembly rather than surface-mount reflow.
The LM2904 family is commonly selected when a design requires a dual amplifier with broad supply-voltage capability and flexible supply configurations. Its internally frequency-compensated architecture simplifies the construction of standard amplifier stages, while the common-mode input range extending toward ground or VEE supports single-supply sensor interfaces. The operating-amplifier category sits within analog integrated circuits and broader signal-chain design, where the device can sit between sensors, analog converters, filters, and actuator drivers.
Typical applications include low-side current or voltage sensing, audio and communications signal conditioning, industrial control modules, regulated power-supply feedback, and general dual-stage amplifier boards. In an instrumentation circuit, the two channels can amplify or buffer two related signals, while in a control system they can monitor a feedback signal and drive a downstream conditioning stage. The device should be selected only after checking the exact onsemi datasheet for input common-mode limits, output swing, output-current capability, electrical characteristics, and package details.
The principal design consideration is supply and signal-headroom management. Although the LM2904 family supports single-supply operation, the usable output range and input common-mode range are not identical to the supply range. Resistor networks, decoupling capacitors, and careful grounding should be selected according to the manufacturer application guidance. This page combines the exact package, amplifier, voltage, bandwidth, slew-rate, and supply information shown in the component records with practical guidance for evaluating the LM2904VNG in industrial, communications, audio, sensor, and power-control designs.
ドロップイン代替品: LM2904VNG — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM2904VNG (同一形状・フットプリント) — 相違点: Package, Slew Rate, Mounting Type, Gain-Bandwidth Product, Common-Mode Input Range.
LM2904NG
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904P
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904VDMR2
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904BIDR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904DR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904VNG 最大定格&電気的特性
| Amplifier Type | General Purpose |
| Number of Circuits | 2 circuits |
| Supply Voltage Range | 3 V to 32 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Common-Mode Input Voltage Range | Extends to ground/VEE |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| パッケージ | 8-DIP (0.300 in, 7.62 mm pitch) |
| 実装タイプ | Through-hole |
| Packaging | Tube |
| Product Description | Dual operational amplifier |
| Architecture | Two independent, high-gain, frequency-compensated operational amplifiers |
| Low Power Drain | Supported |
| Input Common-Mode Reference | Ground/VEE |
LM2904VNG 8-dip (0.300 in, 7.62 mm pitch) ピン配置ガイド
LM2904VNG (8-dip (0.300 in, 7.62 mm pitch) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: LM2904VNG.
詳細は データシート をご参照ください。
主な用途
LM2904VNG の用途: 6 件s: Industrial Sensor Signal Conditioning, Power Supply Feedback Monitoring, Audio Preamplifier Stages, Communications Interface Conditioning, Current Monitoring and Control, Industrial Control Module.
Industrial Sensor Signal Conditioning
LM2904VNG fits industrial sensor interfaces that require two independent amplifier channels and a single- or split-supply operating arrangement. Its common-mode input range extends toward ground/VEE, which is useful when a sensor signal is referenced close to the lower rail. The 1 MHz gain-bandwidth product and 0.6 V/µs slew rate are appropriate for general-purpose conditioning of slowly varying or moderate-bandwidth sensor signals. The two channels can buffer or amplify a sensor path and a reference signal in the same module. Design the external feedback network around the closed-loop gain required by the sensor, and verify input and output headroom at the actual supply voltage.
おすすめ
Power Supply Feedback Monitoring
LM2904VNG can monitor and condition a power-supply feedback voltage where a general-purpose dual amplifier is sufficient. One channel may buffer a feedback divider while the second channel amplifies a related current-sense or error signal for an analog controller. Its 3 V to 32 V supply capability supports higher-voltage industrial rails than the 26 V TI LM2904 family member identified in the product records. The 1 MHz bandwidth provides useful response for many control loops, while the 0.6 V/µs slew rate should be checked against large-signal feedback steps. Use the exact onsemi output-swing and common-mode limits at the selected rail.
おすすめ
Audio Preamplifier Stages
LM2904VNG is usable in modest audio preamplifier and buffer stages where low-frequency gain and general-purpose operation are more important than wide-band audio performance. Two channels allow a stereo preamplifier to use a single package, with each amplifier configured through external feedback resistors and coupling capacitors. The 1 MHz gain-bandwidth product and 0.6 V/µs slew rate are sufficient for many spoken-audio and control-signal paths, but they will not match the speed of precision low-noise audio amplifiers. Check the input noise, output swing, and channel-to-channel behavior in the manufacturer datasheet before using it in high-fidelity equipment.
おすすめ
Communications Interface Conditioning
LM2904VNG can condition slow and moderate-bandwidth signals in communications interface boards that require dual amplification, broad supply-voltage tolerance, and through-hole assembly. One channel can buffer an incoming line-level signal while the other handles an outgoing control or level-shifted signal. The common-mode input range extending toward ground/VEE supports single-rail operation, while the 1 MHz gain-bandwidth product provides more bandwidth than many very-low-speed comparators. The 0.6 V/µs slew rate should be considered for pulse-shaped signals, and the circuit must provide appropriate input protection and filtering at the board interface.
おすすめ
Current Monitoring and Control
LM2904VNG is suitable for low-side current-monitoring and control circuits when the shunt voltage remains inside the amplifier’s input common-mode range. One amplifier can amplify the differential voltage across a shunt while the other can buffer or condition the result for an ADC or comparator. The extended common-mode range toward ground is valuable for low-voltage shunt systems, and the dual package simplifies allocation of signal gain and output buffering. The 1 MHz bandwidth and 0.6 V/µs slew rate are adequate for many slow current-control loops. Confirm the shunt signal range, output swing, and settling requirements for the selected feedback network.
おすすめ
Industrial Control Module
LM2904VNG fits small industrial control modules that need two general-purpose analog channels on a through-hole board. A typical arrangement uses one channel to condition a feedback or sensor signal and the other to amplify a control output before it reaches a downstream driver. Single-supply operation reduces the number of required rails, while split-supply operation remains available when bipolar signals are present. The 8-pin PDIP package and tube packaging support conventional through-hole manufacturing. Designers should account for the 0.6 V/µs slew rate, verify the 3 V to 32 V operating envelope, and place suitable bypass capacitance close to the supply pins according to the onsemi layout guidance.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM2904VNG — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM2904NG | LM2904P | LM2904V | LM2904B | LM2904 |
|---|---|---|---|---|---|---|
| Package | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
主な差別化要因
- Higher listed bandwidth than the 700 kHz TI LM2904 comparison part (vs LM2904)
- Broader stated maximum supply than the 26 V TI LM2904 (vs LM2904)
- Single-package dual-channel implementation (vs Single-amplifier alternatives)
設計ノート
The LM2904VNG supports single-supply and split-supply operation, but the usable input and output ranges are narrower than the full 3 V to 32 V supply envelope. Select the rail so that the signal remains inside the manufacturer input common-mode and output swing limits, especially when the sensor output approaches ground. Add local bypass capacitance at the supply pins and use separate routing for sensitive input and output nodes.
Keep the feedback resistors and compensation-related components close to the appropriate amplifier pins, and route each inverting-input node with a short, low-leakage path. Because the device is an 8-pin PDIP, verify the physical hole pattern against the 0.300-inch, 7.62 mm pitch package drawing before committing the PCB footprint. Confirm the numbered pin assignments from the onsemi pin-description table.
Do not treat the 3 V to 32 V supply range as permission to use any input voltage within that range. The input common-mode range and output swing must also be respected. Likewise, the 1 MHz gain-bandwidth product and 0.6 V/µs slew rate limit closed-loop bandwidth and large-signal response. Use the exact LM2904VNG electrical table when designing high-gain, fast-signal, or precision applications.
The LM2904 family uses frequency compensation for general-purpose closed-loop operation, but high source impedance can add noise and reduce practical bandwidth. At sensor inputs, use the lowest practical source impedance, keep input capacitance low, and separate the signal ground path from high-current return paths. Add filtering only after accounting for the amplifier noise and the 1 MHz bandwidth.
コンプライアンス情報
The retrieved component records identify the manufacturer, package, amplifier type, channel count, supply capability, bandwidth, slew rate, and tube packaging. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established and therefore remain unknown.