LM2904VNG - Dual 30V Operational Amplifier | onsemi
MPN: LM2904VNG ✓ Hoạt độngLM2904VNG Tóm tắt
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages while using external feedback to define the closed-loop gain. The dual configuration provides two amplifier channels in one package, making it useful for signal conditioning, buffering, filtering, transducers, instrumentation, and control applications. The LM2904VNG operates from a single supply or split supply, and its common-mode input voltage range extends to ground or VEE. This makes it appropriate for circuits that use low-voltage sensing or single-rail power arrangements where the input signal approaches the lower supply rail.
Key characteristics include two amplifier circuits, a general-purpose amplifier type, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, operation from 3 V to 32 V, and an 8-pin PDIP package. The package is specified as an 8-DIP measuring 0.300 inches, or 7.62 mm, in pitch. The component is identified as a tube-packaged part in the retrieved datasheet description, making it suitable for conventional through-hole PCB assembly rather than surface-mount reflow.
The LM2904 family is commonly selected when a design requires a dual amplifier with broad supply-voltage capability and flexible supply configurations. Its internally frequency-compensated architecture simplifies the construction of standard amplifier stages, while the common-mode input range extending toward ground or VEE supports single-supply sensor interfaces. The operating-amplifier category sits within analog integrated circuits and broader signal-chain design, where the device can sit between sensors, analog converters, filters, and actuator drivers.
Typical applications include low-side current or voltage sensing, audio and communications signal conditioning, industrial control modules, regulated power-supply feedback, and general dual-stage amplifier boards. In an instrumentation circuit, the two channels can amplify or buffer two related signals, while in a control system they can monitor a feedback signal and drive a downstream conditioning stage. The device should be selected only after checking the exact onsemi datasheet for input common-mode limits, output swing, output-current capability, electrical characteristics, and package details.
The principal design consideration is supply and signal-headroom management. Although the LM2904 family supports single-supply operation, the usable output range and input common-mode range are not identical to the supply range. Resistor networks, decoupling capacitors, and careful grounding should be selected according to the manufacturer application guidance. This page combines the exact package, amplifier, voltage, bandwidth, slew-rate, and supply information shown in the component records with practical guidance for evaluating the LM2904VNG in industrial, communications, audio, sensor, and power-control designs.
Bộ thay thế dễ dàng lắp đặt cho LM2904VNG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2904VNG (cùng hình factor và footprint) — khác nhau ở Package, Slew Rate, Mounting Type, Gain-Bandwidth Product, Common-Mode Input Range.
LM2904NG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904P
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904VDMR2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904VNG Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General Purpose |
| Number of Circuits | 2 circuits |
| Supply Voltage Range | 3 V to 32 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Common-Mode Input Voltage Range | Extends to ground/VEE |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/µs |
| Hộp | 8-DIP (0.300 in, 7.62 mm pitch) |
| Kiểu lắp đặt | Through-hole |
| Packaging | Tube |
| Product Description | Dual operational amplifier |
| Architecture | Two independent, high-gain, frequency-compensated operational amplifiers |
| Low Power Drain | Supported |
| Input Common-Mode Reference | Ground/VEE |
Hướng dẫn cấu hình chân LM2904VNG 8-dip (0.300 in, 7.62 mm pitch)
Cấu hình chân cho LM2904VNG (8-dip (0.300 in, 7.62 mm pitch) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2904VNG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2904VNG phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Power Supply Feedback Monitoring, Audio Preamplifier Stages, Communications Interface Conditioning, Current Monitoring and Control, Industrial Control Module.
Industrial Sensor Signal Conditioning
LM2904VNG fits industrial sensor interfaces that require two independent amplifier channels and a single- or split-supply operating arrangement. Its common-mode input range extends toward ground/VEE, which is useful when a sensor signal is referenced close to the lower rail. The 1 MHz gain-bandwidth product and 0.6 V/µs slew rate are appropriate for general-purpose conditioning of slowly varying or moderate-bandwidth sensor signals. The two channels can buffer or amplify a sensor path and a reference signal in the same module. Design the external feedback network around the closed-loop gain required by the sensor, and verify input and output headroom at the actual supply voltage.
Được đề xuất
Power Supply Feedback Monitoring
LM2904VNG can monitor and condition a power-supply feedback voltage where a general-purpose dual amplifier is sufficient. One channel may buffer a feedback divider while the second channel amplifies a related current-sense or error signal for an analog controller. Its 3 V to 32 V supply capability supports higher-voltage industrial rails than the 26 V TI LM2904 family member identified in the product records. The 1 MHz bandwidth provides useful response for many control loops, while the 0.6 V/µs slew rate should be checked against large-signal feedback steps. Use the exact onsemi output-swing and common-mode limits at the selected rail.
Được đề xuất
Audio Preamplifier Stages
LM2904VNG is usable in modest audio preamplifier and buffer stages where low-frequency gain and general-purpose operation are more important than wide-band audio performance. Two channels allow a stereo preamplifier to use a single package, with each amplifier configured through external feedback resistors and coupling capacitors. The 1 MHz gain-bandwidth product and 0.6 V/µs slew rate are sufficient for many spoken-audio and control-signal paths, but they will not match the speed of precision low-noise audio amplifiers. Check the input noise, output swing, and channel-to-channel behavior in the manufacturer datasheet before using it in high-fidelity equipment.
Được đề xuất
Communications Interface Conditioning
LM2904VNG can condition slow and moderate-bandwidth signals in communications interface boards that require dual amplification, broad supply-voltage tolerance, and through-hole assembly. One channel can buffer an incoming line-level signal while the other handles an outgoing control or level-shifted signal. The common-mode input range extending toward ground/VEE supports single-rail operation, while the 1 MHz gain-bandwidth product provides more bandwidth than many very-low-speed comparators. The 0.6 V/µs slew rate should be considered for pulse-shaped signals, and the circuit must provide appropriate input protection and filtering at the board interface.
Được đề xuất
Current Monitoring and Control
LM2904VNG is suitable for low-side current-monitoring and control circuits when the shunt voltage remains inside the amplifier’s input common-mode range. One amplifier can amplify the differential voltage across a shunt while the other can buffer or condition the result for an ADC or comparator. The extended common-mode range toward ground is valuable for low-voltage shunt systems, and the dual package simplifies allocation of signal gain and output buffering. The 1 MHz bandwidth and 0.6 V/µs slew rate are adequate for many slow current-control loops. Confirm the shunt signal range, output swing, and settling requirements for the selected feedback network.
Được đề xuất
Industrial Control Module
LM2904VNG fits small industrial control modules that need two general-purpose analog channels on a through-hole board. A typical arrangement uses one channel to condition a feedback or sensor signal and the other to amplify a control output before it reaches a downstream driver. Single-supply operation reduces the number of required rails, while split-supply operation remains available when bipolar signals are present. The 8-pin PDIP package and tube packaging support conventional through-hole manufacturing. Designers should account for the 0.6 V/µs slew rate, verify the 3 V to 32 V operating envelope, and place suitable bypass capacitance close to the supply pins according to the onsemi layout guidance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2904VNG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2904NG | LM2904P | LM2904V | LM2904B | LM2904 |
|---|---|---|---|---|---|---|
| Package | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) | 8-DIP (0.300 in, 7.62 mm pitch) |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
Bảo phân biệt quan trọng
- Higher listed bandwidth than the 700 kHz TI LM2904 comparison part (vsLM2904)
- Broader stated maximum supply than the 26 V TI LM2904 (vsLM2904)
- Single-package dual-channel implementation (vsSingle-amplifier alternatives)
Ghi chú thiết kế
The LM2904VNG supports single-supply and split-supply operation, but the usable input and output ranges are narrower than the full 3 V to 32 V supply envelope. Select the rail so that the signal remains inside the manufacturer input common-mode and output swing limits, especially when the sensor output approaches ground. Add local bypass capacitance at the supply pins and use separate routing for sensitive input and output nodes.
Keep the feedback resistors and compensation-related components close to the appropriate amplifier pins, and route each inverting-input node with a short, low-leakage path. Because the device is an 8-pin PDIP, verify the physical hole pattern against the 0.300-inch, 7.62 mm pitch package drawing before committing the PCB footprint. Confirm the numbered pin assignments from the onsemi pin-description table.
Do not treat the 3 V to 32 V supply range as permission to use any input voltage within that range. The input common-mode range and output swing must also be respected. Likewise, the 1 MHz gain-bandwidth product and 0.6 V/µs slew rate limit closed-loop bandwidth and large-signal response. Use the exact LM2904VNG electrical table when designing high-gain, fast-signal, or precision applications.
The LM2904 family uses frequency compensation for general-purpose closed-loop operation, but high source impedance can add noise and reduce practical bandwidth. At sensor inputs, use the lowest practical source impedance, keep input capacitance low, and separate the signal ground path from high-current return paths. Add filtering only after accounting for the amplifier noise and the 1 MHz bandwidth.
Thông tin tuân thủ
The retrieved component records identify the manufacturer, package, amplifier type, channel count, supply capability, bandwidth, slew rate, and tube packaging. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established and therefore remain unknown.