Texas Instruments

LM393M/NOPB Dual Open-Collector Comparator | Texas Instruments

部品番号: LM393M/NOPB ✓ 生産中
2.0 mV maximum Vdss 8-pin SOIC (D), 3.90 mm width Package
MOQ: 1 |

LM393M/NOPB 概要

The Texas Instruments LM393M/NOPB is a low-power dual differential comparator with an offset voltage specification as low as 2.0 mV maximum, designed for single-supply operation over a wide voltage range. It is packaged in an 8-pin SOIC (D) and uses open-collector outputs suitable for TTL, MOS, and CMOS-compatible interfacing.

A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input exceeds the other. The LM393 family contains two independent comparators, allowing one package to perform two threshold, level-detection, or overvoltage-monitoring functions. In the wider semiconductor hierarchy, it is a linear comparator IC, a type of analog signal-conditioning component used before digital logic inputs.

The LM393M/NOPB provides low quiescent current and a broad common-mode input range, making it suitable for battery-operated equipment, industrial control systems, sensor interfaces, and simple protection circuits. Its open-collector output stage requires an external pull-up resistor when the output must drive a logic high. This architecture also allows several open-collector outputs to be wired together when the application requires a wired-AND function.

Each comparator includes independently selectable input polarity and low input-bias behavior suited to threshold decisions. The device can operate from a single supply or from split positive and negative rails, depending on the system requirements. Its 8-pin SOIC package is widely supported by standard PCB footprints and automated assembly processes, while the -NOPB ordering code identifies a lead-free, halogen-free commercial-grade configuration.

Typical uses include battery-voltage monitoring, window comparators, temperature thresholds, overcurrent detection, signal crossing detection, and logic-level translation. Because the output is open collector, the output high voltage is determined by the pull-up supply rather than by the comparator itself. This feature is useful when driving a higher-voltage relay, opto-isolator, or open-drain bus.

When designing a new PCB, place the input resistors, bypass capacitor, and pull-up resistors close to the device. Keep comparator inputs away from switching nodes and high-current paths to minimize offset errors and false switching. Confirm the operating temperature range, absolute maximum ratings, common-mode limits, and output pull-up requirements against the manufacturer datasheet before releasing the design.

ドロップイン代替品: LM393M/NOPB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: LM393M/NOPB (同一形状・フットプリント) — 相違点: Package, Operating Temperature Range, Output Type, Comparator Type, Number of Comparators.

Texas Instruments
Package: SOIC-8 (D suffix)
Operating Temperature Range: 0°C to +70°C (LM393 commercial grade)
Output Type: Open-collector, rail-to-rail input capable
Texas Instruments
Package: 8-SOIC
Texas Instruments
Package: SOIC (D), 8 pins
Operating Temperature Range: 0 C to 70 C
Output Type: Open collector
Texas Instruments
Package: 8-PDIP (DIP-8, through-hole)
Operating Temperature Range: 0 C to +70 C (LM393N) / -40 C to +85 C (LM2903N)
Output Type: Open-Collector / Open-Drain (single-ended)
Texas Instruments
Package: PDIP-8
Operating Temperature Range: 0°C to +70°C
Comparator Type: General-purpose dual comparator

LM393M

✅ ドロップイン
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 · Open-Collector · Standard general purpose · 2 V to 36 V · 1.4 microseconds · 8-SOIC · 8 pins

価格はお問い合わせください

データシートを見る →

LM393N/NOPB

✅ ドロップイン
Texas Instruments
📦 8-SOIC
General-purpose dual comparator · 2 · 2 · 2.0 mV maximum · Single supply or split supply · Open-collector · PDIP-8 · 8 pins

価格はお問い合わせください

データシートを見る →

LM393N

✅ ドロップイン
Texas Instruments
📦 8-SOIC
Dual General-Purpose Comparator · 2 (dual) · Open-Collector / Open-Drain (single-ended) · 5 mV (LM393N); 2 mV (LM193/LM393A grade) · 25 nA · 2 V to 36 V · ±1 V to ±18 V · 16 mA

価格はお問い合わせください

データシートを見る →

LM393M/NOPB

✅ ドロップイン
Texas Instruments
📦 8-SOIC
Dual differential voltage comparator · 2 · Open-collector · 2.0 mV maximum · 0 °C to 70 °C

価格はお問い合わせください

データシートを見る →

LM393

✅ ドロップイン
Texas Instruments
📦 8-SOIC
2 (dual independent) · 2 V to 30 V · ±1 V to ±15 V · 2.0 mV (typical) · ±38 V · Includes ground (V-) · Open-collector, rail-to-rail input capable · TTL, MOS, CMOS (with external pull-up)

価格はお問い合わせください

データシートを見る →

LM393M/NOPB 最大定格&電気的特性

Comparator Type Dual differential voltage comparator
Number of Comparators 2
出力タイプ Open-collector
Input Offset Voltage 2.0 mV maximum
動作温度範囲 0 °C to 70 °C
パッケージ 8-pin SOIC (D), 3.90 mm width
実装タイプ Surface mount
Output Compatibility TTL, MOS, and CMOS compatible
Supply Configuration Single-supply operation
Lead-Free Ordering Code NOPB
AEC-Q100 Qualification Not applicable

LM393M/NOPB ピン構成

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
ピン 1 OUT 1 — Open-collector output of comparator 1
ピン 2 IN 1− — Inverting input of comparator 1
ピン 3 IN 1+ — Non-inverting input of comparator 1
ピン 4 GND — Ground connection
ピン 5 IN 2+ — Non-inverting input of comparator 2
ピン 6 IN 2− — Inverting input of comparator 2
ピン 7 OUT 2 — Open-collector output of comparator 2
ピン 8 VCC — Positive supply connection

主な用途

LM393M/NOPB の用途: 6 件s: Battery Voltage Monitoring, Overvoltage and Undervoltage Protection, Industrial Sensor Interface, Signal Crossing Detection, LED and Lighting Control, Audio and Interface Level Detection.

⚡

Battery Voltage Monitoring

The LM393M/NOPB fits battery threshold detection because it contains two independent low-power comparators and supports single-supply operation. One channel can compare a divided battery voltage with a precision reference while the other monitors a second rail or state. The open-collector output can directly pull down a system enable or fault line when configured with an external pull-up. This arrangement avoids continuously energizing a microcontroller input path, although the comparator's supply and input-bias current should be included in the overall battery budget. The SOIC-8 package also provides a compact layout with separate inverting and non-inverting inputs for each channel.

🏭

Overvoltage and Undervoltage Protection

The LM393M/NOPB can implement independent overvoltage and undervoltage windows around a protected power rail. Each comparator receives a divided rail voltage and a threshold reference, while its open-collector output provides a wired fault indication. Because the outputs are open collector, a pull-up can establish the fault logic level and multiple channels may share a common bus. The 2.0 mV maximum input offset specification supports accurate threshold decisions, but resistor tolerance, reference drift, input common-mode limits, and propagation delay still determine the practical protection margins.

🏭

Industrial Sensor Interface

The LM393M/NOPB is appropriate for discrete industrial sensors that produce a slowly changing voltage, such as a potentiometer, thermistor network, or resistive probe. The comparator converts the analog crossing point into a digital event, and the open-collector output can drive an alert input, relay-control circuit, or optocoupler. Its wide operating voltage concept is useful in 24 V-class control systems, although the exact common-mode range must include the sensor node voltage. Input filtering and a pull-back resistor can limit noise pickup when long sensor wiring increases susceptibility to transients and switching interference.

🌐

Signal Crossing Detection

The LM393M/NOPB can detect when a moving or periodic analog signal crosses a defined threshold. One comparator may establish an upper limit while the other establishes a lower limit, producing a window or hysteresis function. Its two independent channels are useful in zero-crossing, saturation, or direction-detection circuits. An open-collector output allows the event to be pulled up to the receiving logic's supply, but propagation delay and input overdrive affect event timing. For high-speed signals or very low overshoot requirements, a faster comparator family may provide better control than this low-power bipolar device.

💡

LED and Lighting Control

The LM393M/NOPB can provide a simple illumination threshold by comparing a light-dependent divider against a reference and controlling an LED driver stage. The open-collector output is convenient for driving an N-channel transistor, which can switch the LED current from a higher-voltage rail. Using both comparator channels allows automatic light-on and light-off thresholds, creating hysteresis and preventing visible flicker around the transition point. Care should be taken to maintain the LED current within the transistor and supply limits and to keep sensor traces away from the switched LED current path.

🎧

Audio and Interface Level Detection

The LM393M/NOPB can monitor an audio or communications line when the task is threshold detection rather than high-fidelity signal processing. Its open-collector output is useful for signaling a downstream digital device, muting a circuit, or asserting an interrupt. The low-offset characteristic can help reduce threshold ambiguity, while the two channels permit separate detection of positive and negative excursions. Designers should add filtering to avoid responding to broadband noise and must confirm that input bias current, common-mode range, and output timing meet the interface requirements.

What is the LM393M/NOPB?
The LM393M/NOPB is a Texas Instruments dual differential comparator containing two independent comparator channels in an 8-pin SOIC package. According to the manufacturer product information, it is a low-power, low-offset-voltage device intended for single-supply operation, with an input offset voltage specification as low as 2.0 mV maximum. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic when used with an appropriate pull-up resistor.
What are the key specifications of LM393M/NOPB that engineers should know?
The LM393M/NOPB is a dual, low-power, open-collector comparator in an 8-pin SOIC package. Its most important published characteristics are two independent comparator channels, an input offset voltage as low as 2.0 mV maximum, operation from a single supply over a wide voltage range, and outputs compatible with TTL, MOS, and CMOS logic. The commercial temperature range shown for the LM393M/NOPB ordering option is 0 °C to 70 °C.
Where can I download the LM393M/NOPB datasheet PDF?
The LM393M/NOPB datasheet and product information are available from Texas Instruments through the official LM393-N product page at https://www.ti.com/product/LM393-N/part-details/LM393M/NOPB. The manufacturer describes the device as a low-power, low-offset-voltage dual comparator. Use the manufacturer document for final pin functions, absolute maximum ratings, electrical characteristics, and application guidance before committing a production design.
Where can I find the LM393M pinout?
The LM393M pinout is defined in the manufacturer datasheet and corresponds to the 8-pin SOIC (D) package: pins 1 and 7 are the two open-collector outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are non-inverting inputs, pin 4 is ground, and pin 8 is the positive supply. Use the package drawing and pin-description table in the Texas Instruments datasheet when assigning PCB tracks.
Does LM393M/NOPB need a pull-up resistor?
Yes, each open-collector output normally requires an external pull-up resistor to establish a logic-high voltage. The pull-up rail can be selected independently of the comparator supply when the circuit must drive a different logic level. The resistor value should balance rise time, signal bandwidth, power consumption, and the current required when the output transistor is pulling low.
What is the difference between LM393M/NOPB and LM393N/NOPB?
LM393M/NOPB and LM393N/NOPB belong to the same Texas Instruments LM393-N family, but the ordering suffix identifies different package variants. LM393M/NOPB is listed in an 8-pin SOIC (D) package, while LM393N/NOPB is the through-hole DIP ordering option. Both provide the same dual-comparator function and open-collector architecture, but their PCB footprints are not interchangeable.
Is the onsemi LM393M a drop-in replacement for LM393M/NOPB?
The onsemi LM393M can serve as a same-package replacement candidate because it is an 8-SOIC dual comparator with the same LM393-family open-collector function. Texas Instruments and onsemi describe equivalent device families, but engineers should still verify offset voltage, supply range, common-mode range, propagation delay, output-current limits, and temperature coverage against the current datasheets before approving the substitution.
Can LM393M/NOPB operate from a single supply voltage?
Yes, the LM393M/NOPB is specifically designed to operate from a single power supply over a wide range of voltages. In a single-supply circuit, the non-inverting input is commonly biased above ground with a resistor divider, while the inverting input establishes the threshold. The datasheet's supply and common-mode limits must be respected for every voltage and temperature condition.
Where can I buy LM393M/NOPB and check current lead time?
Use the Request a Quote form on this page to request LM393M/NOPB pricing, stock confirmation, current lead time, and package quantity requirements. The manufacturer identifies LM393M/NOPB as active. Because inventory and commercial terms can change rapidly, request the quantity, date code, and shipment destination with the quotation rather than relying on a static listing.
What is the price of LM393M/NOPB?
Current commercial pricing for LM393M/NOPB should be obtained through the Request a Quote form on this page. The form can return a quantity-specific quote for the exact Texas Instruments part number and package. Confirm the requested quantity, authorized supply status, date code, and shipping terms before placing an order.
What is the lead time for LM393M/NOPB?
The current lead time for LM393M/NOPB is best confirmed through the Request a Quote form on this page. Submit the required order quantity, package format, target price, and shipment destination. The manufacturer lists the LM393M/NOPB ordering option as active, but actual availability can vary with production schedules and order volume.
Is LM393M/NOPB in stock?
Stock status for LM393M/NOPB should be checked through the Request a Quote form on this page using the exact part number LM393M/NOPB and the required order quantity. The manufacturer lists this ordering option as active. The quotation team can confirm current inventory, expected delivery timing, and any package or date-code constraints.
When should I choose LM393M/NOPB over a CMOS comparator?
Choose LM393M/NOPB when an open-drain interface, single-supply operation, broad input-voltage capability, and compatibility with the established LM393 footprint are more important than the very low supply current of a CMOS comparator. A CMOS alternative may be preferable for battery-powered operation when its lower quiescent current and specified supply range fit the design. Verify input thresholds, output speed, and logic compatibility.
What is the best drop-in replacement for LM393M/NOPB?
The strongest drop-in replacement candidates identified for LM393M/NOPB are 8-SOIC versions of the LM393 family from Texas Instruments, onsemi, STMicroelectronics, and National Semiconductor. The closest functional substitute is the onsemi LM393M because it uses the same 8-SOIC format and standard LM393 comparator function. No replacement should be approved without checking current electrical ratings, temperature range, offset voltage, and output behavior.
What can replace LM393M/NOPB in an existing PCB?
A drop-in replacement for LM393M/NOPB must use the same 8-SOIC footprint and preserve the open-collector output arrangement. The onsemi LM393M is a direct candidate, while LM393N/NOPB is not appropriate for the same PCB because it uses a through-hole DIP package. Confirm the replacement's input-pin functions, maximum supply voltage, common-mode range, and output sink-current capability before substitution.
Is LM393M/NOPB suitable for battery-powered sensor monitoring?
The LM393M/NOPB is suitable for many battery-powered threshold-monitoring circuits because it is a low-power comparator with an open-collector output and single-supply operation. Its supply current and input bias characteristics must be checked against the battery budget at the intended temperature. A CMOS comparator may offer lower quiescent current in applications where every microampere affects battery life.

エンジニアリング参考データ: LM393M/NOPB — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose LM393M/NOPB when the design requires two independent low-power comparators, an open-collector output, single-supply operation, and an 8-pin SOIC footprint. It is a practical choice for threshold detection, voltage supervision, and industrial sensing where TTL, MOS, or CMOS interfacing is required. The onsemi LM393M is the closest cross-brand candidate to compare because it uses the same 8-SOIC LM393-family format, but verify offset voltage, propagation delay, common-mode limits, and temperature ratings. A TI LM393-family option may simplify procurement or qualification where manufacturer continuity matters. Do not select a through-hole DIP variant for an existing LM393M/NOPB PCB. A CMOS comparator is preferable only when lower quiescent current or faster edge performance is more important than the established LM393 footprint and open-collector behavior.

代替品との比較

パラメータ この製品 LM393M LM393N/NOPB LM393N LM393M/NOPB LM393
Brand Texas Instruments onsemi Texas Instruments STMicroelectronics National Semiconductor Texas Instruments
Package 8-SOIC (D) 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Comparator Count 2 2 2 2 2 2
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector
Single-Supply Operation Yes Yes Yes Yes Yes Yes
Functional Relationship LM393 dual comparator LM393-family dual comparator LM393-N family dual comparator LM393-family dual comparator LM393M/NOPB designation LM393 dual comparator

主な差別化要因

  • Commercial-grade LM393M/NOPB ordering option (vs LM393M/NOPB)
  • Established LM393 dual-comparator architecture (vs LM393M)
  • Low published input-offset specification (vs LM393N)

設計ノート

Do not treat an open-collector output as a push-pull logic output. Fit a pull-up resistor from each output to the voltage required by the receiving logic, and verify that the output transistor can sink the pull-up current. Keep the pull-up connection short, because its resistance and output capacitance determine the rising edge. If several outputs are wired together, ensure the shared pull-up current remains within the sink-current rating.

Route the two comparator input nets as short, quiet traces and place their input resistors close to the corresponding pins. Keep these nets away from switching-regulator switches, relay drivers, inductors, and high-current return paths. A solid ground plane reduces sensitivity to injected noise, while a small input-node capacitance helps limit switching transients. Verify common-mode and absolute-maximum input limits across temperature before finalizing the schematic.

Decouple the supply pin locally with the capacitance recommended by the manufacturer datasheet and place the capacitor between the supply and ground pins using a short current loop. For single-supply operation, bias the non-inverting input above ground so the comparator can resolve a meaningful threshold. Account for comparator input-bias current when selecting high-value divider resistors, since excessive resistance can move the reference voltage and increase noise sensitivity.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Yes
ハロゲンフリー
Yes
紛争鉱物
Unknown

The NOPB ordering code identifies a lead-free, halogen-free commercial-grade device. RoHS, REACH, and conflict-minerals declarations were not confirmed and remain unknown.

データ検証日: 2026-11-17 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

lm393m nopb lm393m datasheet lm393m pinout lm393m datasheet pdf lm393m pdf lm393m equivalent lm393m replacement lm393m cross reference lm393m vs lm393n lm393m application circuit lm393m open collector output lm393m 8 soic footprint

関連部品&用語

Texas Instruments LM393M/NOPB LM393 LM393M LM393N/NOPB onsemi STMicroelectronics National Semiconductor dual differential comparator comparator IC analog IC linear IC open-collector output input offset voltage common-mode input range single-supply operation TTL compatible MOS compatible CMOS compatible 8-pin SOIC SOIC package family surface-mount device battery voltage monitoring industrial sensor interface lead-free packaging
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示