LM393M/NOPB Dual Open-Collector Comparator | Texas Instruments
MPN: LM393M/NOPB ✓ Hoạt độngLM393M/NOPB Tóm tắt
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input exceeds the other. The LM393 family contains two independent comparators, allowing one package to perform two threshold, level-detection, or overvoltage-monitoring functions. In the wider semiconductor hierarchy, it is a linear comparator IC, a type of analog signal-conditioning component used before digital logic inputs.
The LM393M/NOPB provides low quiescent current and a broad common-mode input range, making it suitable for battery-operated equipment, industrial control systems, sensor interfaces, and simple protection circuits. Its open-collector output stage requires an external pull-up resistor when the output must drive a logic high. This architecture also allows several open-collector outputs to be wired together when the application requires a wired-AND function.
Each comparator includes independently selectable input polarity and low input-bias behavior suited to threshold decisions. The device can operate from a single supply or from split positive and negative rails, depending on the system requirements. Its 8-pin SOIC package is widely supported by standard PCB footprints and automated assembly processes, while the -NOPB ordering code identifies a lead-free, halogen-free commercial-grade configuration.
Typical uses include battery-voltage monitoring, window comparators, temperature thresholds, overcurrent detection, signal crossing detection, and logic-level translation. Because the output is open collector, the output high voltage is determined by the pull-up supply rather than by the comparator itself. This feature is useful when driving a higher-voltage relay, opto-isolator, or open-drain bus.
When designing a new PCB, place the input resistors, bypass capacitor, and pull-up resistors close to the device. Keep comparator inputs away from switching nodes and high-current paths to minimize offset errors and false switching. Confirm the operating temperature range, absolute maximum ratings, common-mode limits, and output pull-up requirements against the manufacturer datasheet before releasing the design.
Bộ thay thế dễ dàng lắp đặt cho LM393M/NOPB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM393M/NOPB (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature Range, Output Type, Comparator Type, Number of Comparators.
LM393M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393N/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393M/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM393M/NOPB Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential voltage comparator |
| Number of Comparators | 2 |
| Kiểu đầu ra | Open-collector |
| Input Offset Voltage | 2.0 mV maximum |
| Khoảng nhiệt độ hoạt động | 0 °C to 70 °C |
| Hộp | 8-pin SOIC (D), 3.90 mm width |
| Kiểu lắp đặt | Surface mount |
| Output Compatibility | TTL, MOS, and CMOS compatible |
| Supply Configuration | Single-supply operation |
| Lead-Free Ordering Code | NOPB |
| AEC-Q100 Qualification | Not applicable |
Cấu hình chân LM393M/NOPB
| Chân 1 | OUT 1 — Open-collector output of comparator 1 |
| Chân 2 | IN 1− — Inverting input of comparator 1 |
| Chân 3 | IN 1+ — Non-inverting input of comparator 1 |
| Chân 4 | GND — Ground connection |
| Chân 5 | IN 2+ — Non-inverting input of comparator 2 |
| Chân 6 | IN 2− — Inverting input of comparator 2 |
| Chân 7 | OUT 2 — Open-collector output of comparator 2 |
| Chân 8 | VCC — Positive supply connection |
Ứng dụng tiêu biểu
LM393M/NOPB phù hợp cho 6 Áp dụngs: Battery Voltage Monitoring, Overvoltage and Undervoltage Protection, Industrial Sensor Interface, Signal Crossing Detection, LED and Lighting Control, Audio and Interface Level Detection.
Battery Voltage Monitoring
The LM393M/NOPB fits battery threshold detection because it contains two independent low-power comparators and supports single-supply operation. One channel can compare a divided battery voltage with a precision reference while the other monitors a second rail or state. The open-collector output can directly pull down a system enable or fault line when configured with an external pull-up. This arrangement avoids continuously energizing a microcontroller input path, although the comparator's supply and input-bias current should be included in the overall battery budget. The SOIC-8 package also provides a compact layout with separate inverting and non-inverting inputs for each channel.
Được đề xuất
Overvoltage and Undervoltage Protection
The LM393M/NOPB can implement independent overvoltage and undervoltage windows around a protected power rail. Each comparator receives a divided rail voltage and a threshold reference, while its open-collector output provides a wired fault indication. Because the outputs are open collector, a pull-up can establish the fault logic level and multiple channels may share a common bus. The 2.0 mV maximum input offset specification supports accurate threshold decisions, but resistor tolerance, reference drift, input common-mode limits, and propagation delay still determine the practical protection margins.
Được đề xuất
Industrial Sensor Interface
The LM393M/NOPB is appropriate for discrete industrial sensors that produce a slowly changing voltage, such as a potentiometer, thermistor network, or resistive probe. The comparator converts the analog crossing point into a digital event, and the open-collector output can drive an alert input, relay-control circuit, or optocoupler. Its wide operating voltage concept is useful in 24 V-class control systems, although the exact common-mode range must include the sensor node voltage. Input filtering and a pull-back resistor can limit noise pickup when long sensor wiring increases susceptibility to transients and switching interference.
Được đề xuất
Signal Crossing Detection
The LM393M/NOPB can detect when a moving or periodic analog signal crosses a defined threshold. One comparator may establish an upper limit while the other establishes a lower limit, producing a window or hysteresis function. Its two independent channels are useful in zero-crossing, saturation, or direction-detection circuits. An open-collector output allows the event to be pulled up to the receiving logic's supply, but propagation delay and input overdrive affect event timing. For high-speed signals or very low overshoot requirements, a faster comparator family may provide better control than this low-power bipolar device.
Được đề xuất
LED and Lighting Control
The LM393M/NOPB can provide a simple illumination threshold by comparing a light-dependent divider against a reference and controlling an LED driver stage. The open-collector output is convenient for driving an N-channel transistor, which can switch the LED current from a higher-voltage rail. Using both comparator channels allows automatic light-on and light-off thresholds, creating hysteresis and preventing visible flicker around the transition point. Care should be taken to maintain the LED current within the transistor and supply limits and to keep sensor traces away from the switched LED current path.
Được đề xuất
Audio and Interface Level Detection
The LM393M/NOPB can monitor an audio or communications line when the task is threshold detection rather than high-fidelity signal processing. Its open-collector output is useful for signaling a downstream digital device, muting a circuit, or asserting an interrupt. The low-offset characteristic can help reduce threshold ambiguity, while the two channels permit separate detection of positive and negative excursions. Designers should add filtering to avoid responding to broadband noise and must confirm that input bias current, common-mode range, and output timing meet the interface requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM393M/NOPB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM393M | LM393N/NOPB | LM393N | LM393M/NOPB | LM393 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | onsemi | Texas Instruments | STMicroelectronics | National Semiconductor | Texas Instruments |
| Package | 8-SOIC (D) | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Comparator Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Single-Supply Operation | Yes | Yes | Yes | Yes | Yes | Yes |
| Functional Relationship | LM393 dual comparator | LM393-family dual comparator | LM393-N family dual comparator | LM393-family dual comparator | LM393M/NOPB designation | LM393 dual comparator |
Bảo phân biệt quan trọng
- Commercial-grade LM393M/NOPB ordering option (vsLM393M/NOPB)
- Established LM393 dual-comparator architecture (vsLM393M)
- Low published input-offset specification (vsLM393N)
Ghi chú thiết kế
Do not treat an open-collector output as a push-pull logic output. Fit a pull-up resistor from each output to the voltage required by the receiving logic, and verify that the output transistor can sink the pull-up current. Keep the pull-up connection short, because its resistance and output capacitance determine the rising edge. If several outputs are wired together, ensure the shared pull-up current remains within the sink-current rating.
Route the two comparator input nets as short, quiet traces and place their input resistors close to the corresponding pins. Keep these nets away from switching-regulator switches, relay drivers, inductors, and high-current return paths. A solid ground plane reduces sensitivity to injected noise, while a small input-node capacitance helps limit switching transients. Verify common-mode and absolute-maximum input limits across temperature before finalizing the schematic.
Decouple the supply pin locally with the capacitance recommended by the manufacturer datasheet and place the capacitor between the supply and ground pins using a short current loop. For single-supply operation, bias the non-inverting input above ground so the comparator can resolve a meaningful threshold. Account for comparator input-bias current when selecting high-value divider resistors, since excessive resistance can move the reference voltage and increase noise sensitivity.
Thông tin tuân thủ
The NOPB ordering code identifies a lead-free, halogen-free commercial-grade device. RoHS, REACH, and conflict-minerals declarations were not confirmed and remain unknown.