MAX211IDBRE4 - 5V RS-232 Transceiver | Texas Instruments
部品番号: MAX211IDBRE4 ✓ 生産中MAX211IDBRE4 概要
An RS-232 transceiver is an interface IC that converts low-voltage digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the hierarchy of RS-232 interface transceivers, multi-channel line drivers and receivers, interface ICs, and semiconductors. Such devices simplify bidirectional serial connectivity between equipment such as industrial controllers, test equipment, and legacy computer peripherals.
The MAX211IDBRE4 combines four line drivers with five receivers, allowing four outputs and five inputs to share one interface package. Its maximum data rate of 120 kbit/s suits legacy serial ports and control links. Input receiver hysteresis of 500 mV improves noise immunity, while ±15 kV HBM protection improves tolerance of electrostatic discharge on serial-port connections. The specified 5 V operation is compatible with conventional 5 V digital systems.
Internally, the receiver side uses Schmitt-trigger inputs, which provide hysteresis between the low and high switching thresholds. This helps prevent repeated switching as a noisy input crosses the transition region. The integrated driver and receiver functions support asymmetric channel counts, while the shutdown circuit reduces supply current to 1 µA typical when the interface is not active. These characteristics make the device useful where several RS-232 ports must share a common logic-side supply.
Typical applications include multiport industrial controllers, programmable logic controller communications, test and measurement equipment, instrument-control interfaces, and legacy peripheral connections. The 28-pin SSOP surface-mount package also allows reuse of an existing MAX211-family circuit footprint without changing to a through-hole package.
Design the circuit with short, appropriately terminated RS-232 routes, maintain the specified 4.5 V to 5.5 V supply range, and account for ground potential differences between connected equipment. Use the manufacturer pin-description table and application guidance when assigning connector-side and logic-side signals. Verify shutdown-state behavior and ESD requirements at the complete system level.
This page combines the MAX211IDBRE4 electrical specifications, package details, RS-232 design guidance, comparison parameters, and qualified drop-in alternatives to support faster component selection and PCB-level replacement decisions.
ドロップイン代替品: MAX211IDBRE4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MAX211IDBRE4 (同一形状・フットプリント) — 相違点: Product Type, Maximum Data Rate, Interface Standard, Operating Temperature Range, Package.
MAX211IDBR
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX211IDBRG4
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX213IDBR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX211CAI+T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX211ECAI+
✅ ドロップイン価格はお問い合わせください
データシートを見る →HIN211ECAZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ADM211ARSZ
✅ ドロップイン価格はお問い合わせください
データシートを見る →MAX211IDBRE4 仕様
| Product Type | 5 V multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Number of Drivers | 4 drivers |
| Number of Receivers | 5 receivers |
| Maximum Data Rate | 120 kbit/s |
| ESD Protection | ±15 kV using the Human-Body Model |
| Receiver Hysteresis | 500 mV |
| Shutdown Supply Current | 1 µA typical |
| 動作温度範囲 | -40°C to +85°C |
| パッケージ | 28-pin SSOP |
| 実装タイプ | Surface mount |
| RS-232 Standards | TIA/EIA-232-F and ITU V.28 |
| Logic Input Type | Schmitt trigger |
| Transceiver Configuration | 4/5 full RS-232 transceiver |
| RoHS ステータス | Compliant |
MAX211IDBRE4 28-pin ssop ピン配置ガイド
MAX211IDBRE4 (28-pin ssop パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MAX211IDBRE4.
詳細は データシート をご参照ください。
主な用途
MAX211IDBRE4 の用途: 6 件s: Industrial Controller Serial Interfaces, Programmable Logic Controller Communication, Test and Measurement Equipment, Instrument and Peripheral Control, Data Acquisition Systems, Legacy Computer Peripheral Interfaces.
Industrial Controller Serial Interfaces
The MAX211IDBRE4 fits industrial controllers requiring several legacy RS-232 ports on one logic-side supply. Four drivers support outbound serial channels, while five receivers provide additional inbound connections without requiring five separate interface packages. Its 120 kbit/s maximum rate is appropriate for supervisory links and low-bandwidth equipment, while the 500 mV receiver hysteresis helps reject noise around the logic threshold. Place the device near the connector-side circuitry, keep return paths short, and verify that shutdown and enable sequencing satisfies the controller’s power-management requirements.
おすすめ
Programmable Logic Controller Communication
The four-driver, five-receiver arrangement of the MAX211IDBRE4 supports multiport PLC communication modules that must exchange commands with several external devices. Its 4.5 V to 5.5 V operating range permits use with conventional 5 V logic, and the -40°C to +85°C rating covers a broad range of industrial equipment. The Schmitt-trigger receiver inputs improve noise immunity in cabinets where cable transients are common. Validate isolation, surge, and ground-transient requirements at the connector because the integrated ±15 kV HBM ESD protection does not replace all system-level protection.
おすすめ
Test and Measurement Equipment
The MAX211IDBRE4 is useful in test and measurement instruments that provide several RS-232 control or data ports to legacy fixtures and computers. Four drivers can operate outbound control channels, while five receivers support additional incoming status signals. The maximum data rate of 120 kbit/s matches many legacy serial instruments and avoids unnecessary high-speed circuitry. Its shutdown current of 1 µA typical also benefits multi-instrument systems that disable unused interfaces between test sequences. Confirm that each connected device observes compatible logic levels, baud rates, and connector pin assignments.
おすすめ
Instrument and Peripheral Control
The MAX211IDBRE4 supports legacy peripherals, analyzers, and laboratory instruments that use RS-232 command interfaces. Its four line drivers and five receivers permit more than one port to be integrated into a compact controller, reducing board area compared with separate single-channel transceivers. Operation to 120 kbit/s covers the slow serial links commonly retained for configuration and diagnostics. Route driver and receiver signals according to the manufacturer pin table, maintain a common logic-side ground, and avoid long unprotected branches inside the enclosure.
おすすめ
Data Acquisition Systems
A multichannel data-acquisition controller can use the MAX211IDBRE4 to connect command and status paths between a central controller and remote measurement modules. The four-driver, five-receiver arrangement supports asymmetric traffic patterns, while the 500 mV receiver hysteresis improves tolerance of noise on slower control lines. The device’s 120 kbit/s limit is appropriate for supervisory and configuration traffic rather than bulk measurement-data streaming. Use separate differential or high-speed links when continuous high-volume transfer is required, and confirm that shutdown states do not interfere with active acquisition sequences.
おすすめ
Legacy Computer Peripheral Interfaces
The MAX211IDBRE4 can bridge legacy RS-232 peripherals to a modern embedded controller while retaining the conventional 28-pin SSOP footprint. Its 5 V supply operation is compatible with many controller boards, and the four-driver, five-receiver arrangement supports several peripheral connections in one package. The 120 kbit/s maximum rate is appropriate for keyboards, printers, service ports, and other low-speed serial equipment. Verify the DE and RE control behavior, connector gender, signal polarity, and grounding scheme before replacing an existing board because these details determine interchangeability.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MAX211IDBRE4 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MAX211IDBR | MAX211IDBRG4 | MAX213IDBR | MAX211CAI+T | MAX211ECAI+ | HIN211ECAZ | ADM211ARSZ |
|---|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Renesas Electronics | Analog Devices |
| Package | 28-pin SSOP | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same |
| Product Type | 5 V multichannel RS-232 line driver/receiver | 5 V multichannel RS-232 line driver/receiver | 5 V multichannel RS-232 line driver/receiver | Multichannel RS-232 transceiver | Multichannel RS-232 transceiver | Multichannel RS-232 transceiver | Multichannel RS-232 transceiver | Multichannel RS-232 transceiver |
主な差別化要因
- Direct same-family PCB replacement (vs MAX211IDBR)
- Asymmetric channel allocation reduces package count (vs HIN211ECAZ)
- Specified noise margin for slower control links (vs ADM211ARSZ)
設計ノート
Do not treat every MAX211-family ordering code as automatically interchangeable. Confirm the DE, RE, EN, and shutdown connections against the manufacturer pin-description table for MAX211IDBRE4 and the proposed replacement. In particular, verify whether a receiver remains active in shutdown and whether the enable polarity matches the host logic. A matching 28-pin SSOP outline is necessary for PCB reuse but does not by itself guarantee functional compatibility.
Place the MAX211IDBRE4 close to the RS-232 connector and keep driver and receiver traces short and away from sensitive high-impedance analog nodes. Maintain a continuous logic-side ground reference and route connector-side return currents without narrow breaks. Review the ground-potential difference between connected equipment because RS-232 can remain functional even when the two systems do not share exactly the same ground potential.
Decouple the 5 V supply locally with the capacitance and placement recommended in the Texas Instruments datasheet. Keep the supply within 4.5 V to 5.5 V and account for the dynamic current drawn by multiple RS-232 drivers. The 1 µA shutdown current is a low-power figure, but it applies only when the device is correctly commanded into shutdown; logic-level control must not leave an unintended load on the rail.
Use the 500 mV receiver hysteresis as part of the noise-immunity design, but also control cable routing and connector grounding. Avoid long unprotected cable stubs, particularly when unused driver outputs are connected to external equipment. Confirm baud rate, data polarity, and handshake direction in the system specification because the transceiver's electrical protection does not resolve protocol-level incompatibility.
コンプライアンス情報
RoHS compliance is identified in the MAX211IDBRE4 product listing. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or supplier.