MC9S12C32VFAE16 - 16-Bit HCS12 MCU, 32KB Flash, 48-LQFP | NXP
部品番号: MC9S12C32VFAE16 ✗ 生産終了| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.45 | $9.45 |
| 10 | $8.62 | $86.20 |
| 100 | $7.95 | $795.00 |
| 500 | $7.18 | $3,590.00 |
| 1,000 | $6.42 | $6,420.00 |
MC9S12C32VFAE16 概要
A 16-bit microcontroller (MCU) is a single-chip computer that combines a CPU, memory, and peripheral set on one die. The HCS12 (also called CPU12) is NXP/Freescale's enhanced 16-bit CISC core that adds indexed addressing and improved instructions over the original HC11 architecture. Within NXP's MCU taxonomy, the MC9S12C32 belongs to the S12C sub-family, a cost-optimized member of the broader S12X/S12/S12XE family that targets general-purpose industrial and automotive body network nodes where 8-bit MCUs lack throughput but full S12XE peripherals would be overkill.
Key features of the MC9S12C32VFAE16 include 32KB Flash program memory arranged as 32K x 8, 2KB of static RAM, an integrated CAN 2.0 A/B controller (msCAN) for in-vehicle or industrial networking, an 8-channel 10-bit ADC, an Enhanced Capture Timer (ECT), PWM timers, SPI and SCI (UART) serial interfaces, and a built-in bandgap-based voltage regulator that derives the internal core supply from the external 5V rail. The 48-LQFP package provides a compact footprint and supports an operating temperature range of -40C to +105C or -40C to +125C depending on the specific test condition.
Architecturally, the part uses a von Neumann 16-bit CISC core with two accumulator/index register pairs, immediate, extended, indexed, and relative addressing modes, and a single-wire background debug mode (BDM) interface for non-intrusive in-system programming. The 5V-tolerant I/O simplifies integration in 5V digital systems without level shifters, and the internal regulator removes the need for an external 1.8V or 2.5V LDO.
Typical applications include automotive body controllers (BCM), HVAC control panels, instrument cluster sub-modules, seat control ECUs, industrial sensor nodes, and CAN-based distributed I/O. The part is also a frequent choice in LIN-to-CAN bridges when paired with an external LIN transceiver.
When designing with the MC9S12C32VFAE16, ensure the BDM interface (BKGD, MODC, RESET*) is brought out to a debug header for production programming and field firmware updates, and observe the 5V supply decoupling layout specified in the S12C reference manual to keep ADC readings clean.
This page synthesizes distributor pricing, NRND lifecycle notes, verified 48-LQFP drop-in alternatives from the same S12C family, and practical design guidance not found in the standalone manufacturer datasheet.
ドロップイン代替品: MC9S12C32VFAE16 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC9S12C32VFAE16 （同一形状・フットプリント） — 相違点: Package, Program Memory Size, ADC, RAM Size, Peripherals.
クイック比較ツール — 並列比較する代替部品を選択:
MC9S12C32VFAE10
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
MC9S12C32VFAE25
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
価格はお問い合わせください
データシートを見る →MC9S12C32MFAE16
✅ ドロップイン✓ 在庫あり
$8.2 / 個
データシートを見る →MC9S12GC32VFAE
✅ ドロップイン✓ 在庫あり
$5.64 / 個
データシートを見る →MC9S12C128VFAE
✅ ドロップイン ⚠️ 仕様未検証✓ 在庫あり
$9.75 / 個
データシートを見る →MC9S12GC16MFAE
✅ ドロップイン✓ 在庫あり
$4.1 / 個
データシートを見る →MC9S12C32VFAE16 最大定格＆電気的特性
| Product Family | HCS12 / S12C |
| Core | HCS12 (CPU12) 16-bit |
| Program Memory Size | 32 KB (32K x 8) |
| Program Memory Type | Flash |
| RAM Size | 2 KB (2K x 8) |
| Number of I/O Lines | 31 |
| 電源電圧 | 2.97 V to 5.5 V (5 V typical) |
| Bus Speed | 16 MHz |
| Oscillator Type | Internal |
| PLL | Yes (on-chip) |
| パッケージ / ケース | 48-LQFP (7x7 mm) |
| Package Code | VFAE16 (48-LQFP, 16 MHz grade) |
| 実装タイプ | Surface Mount |
| Peripherals | msCAN 2.0 A/B, 8ch 10-bit ADC, ECT, PWM, SPI, SCI (UART) |
| Temperature Range | -40C to +125C |
| On-chip Voltage Regulator | Yes (bandgap VREG) |
| Packaging | Tray |
| MSLレベル | 3 (per JEDEC J-STD-020) |
| RoHS ステータス | Compliant |
MC9S12C32VFAE16 ピン構成
| ピン 1 | VDDR — Voltage regulator bypass / VDD |
| ピン 2 | VDD — Digital supply input |
| ピン 3 | VSS — Ground |
| ピン 4 | PAD0/AN0 — ADC input 0 / GPIO |
| ピン 5 | PAD1/AN1 — ADC input 1 / GPIO |
| ピン 6 | PAD2/AN2 — ADC input 2 / GPIO |
| ピン 7 | PAD3/AN3 — ADC input 3 / GPIO |
| ピン 8 | PAD4/AN4 — ADC input 4 / GPIO |
| ピン 9 | PAD5/AN5 — ADC input 5 / GPIO |
| ピン 10 | PAD6/AN6 — ADC input 6 / GPIO |
| ピン 11 | PAD7/AN7 — ADC input 7 / GPIO |
| ピン 12 | VDDA — Analog supply |
| ピン 13 | VSSA — Analog ground |
| ピン 14 | PM0/CANTX — Port M GPIO / msCAN TX |
| ピン 15 | PM1/CANRX — Port M GPIO / msCAN RX |
| ピン 16 | PM2/MOSI — Port M GPIO / SPI MOSI |
| ピン 17 | PM3/MISO — Port M GPIO / SPI MISO |
| ピン 18 | PM4/SCK — Port M GPIO / SPI clock |
| ピン 19 | PM5/SS — Port M GPIO / SPI SS |
| ピン 20 | PM6/TxCAN — Port M GPIO / SCI TX |
| ピン 21 | PM7/RxCAN — Port M GPIO / SCI RX |
| ピン 22 | PS0 — Port S GPIO |
| ピン 23 | PS1 — Port S GPIO |
| ピン 24 | PS2 — Port S GPIO |
| ピン 25 | PS3 — Port S GPIO |
| ピン 26 | PS4 — Port S GPIO |
| ピン 27 | PT0/ICOC0 — Port T GPIO / ECT ICOC0 |
| ピン 28 | PT1/ICOC1 — Port T GPIO / ECT ICOC1 |
| ピン 29 | PT2/ICOC2 — Port T GPIO / ECT ICOC2 |
| ピン 30 | PT3/ICOC3 — Port T GPIO / ECT ICOC3 |
| ピン 31 | PT4/ICOC4 — Port T GPIO / ECT ICOC4 |
| ピン 32 | PT5/ICOC5 — Port T GPIO / ECT ICOC5 |
| ピン 33 | PT6/ICOC6 — Port T GPIO / ECT ICOC6 |
| ピン 34 | PT7/ICOC7 — Port T GPIO / ECT ICOC7 |
| ピン 35 | PJ0/TxD — Port J GPIO / SCI TXD alternate |
| ピン 36 | PJ1/RxD — Port J GPIO / SCI RXD alternate |
| ピン 37 | PJ2 — Port J GPIO |
| ピン 38 | PJ3 — Port J GPIO |
| ピン 39 | PJ4 — Port J GPIO |
| ピン 40 | PJ5 — Port J GPIO |
| ピン 41 | PJ6 — Port J GPIO |
| ピン 42 | PJ7 — Port J GPIO |
| ピン 43 | PP0/PWM0 — Port P GPIO / PWM channel 0 |
| ピン 44 | PP1/PWM1 — Port P GPIO / PWM channel 1 |
| ピン 45 | PP2/PWM2 — Port P GPIO / PWM channel 2 |
| ピン 46 | PP3/PWM3 — Port P GPIO / PWM channel 3 |
| ピン 47 | BKGD — Background Debug Mode pin |
| ピン 48 | RESET* — Reset input (active low) |
主な用途
MC9S12C32VFAE16 の用途: 7 件s: Automotive Body Control Module (BCM), HVAC Control Panel and Cluster Sub-Module, Industrial Sensor Node with CANopen, LIN-to-CAN Gateway Bridge, Drone ESC Sub-Controller, Battery Management Slave Cell Monitor, Medical Bed / Adjustable Patient Chair Controller.
Automotive Body Control Module (BCM)
The MC9S12C32VFAE16 is a strong fit for entry-level automotive body controllers that fan out to door modules, lighting, and seat controls via CAN. The integrated msCAN 2.0 A/B interface lets the MCU talk to a TJA1050 5V transceiver directly without external protocol logic, and the 16 MHz CPU provides enough headroom for CANOpen or J1939 stacks at 250-500 kbit/s. The 32 KB Flash holds typical BCM application code including diagnostics, while 2 KB RAM covers stack and periodic message buffers. With the 5V-tolerant I/O and 2.97-5.5V supply, the part interfaces directly to 5V switch inputs and automotive-grade Hall sensors without level translation, and the 48-LQFP footprint is standard for BCM PCB layouts.
おすすめ
HVAC Control Panel and Cluster Sub-Module
In HVAC head units and instrument-cluster sub-blades, the MC9S12C32VFAE16 drives LED matrices, rotary encoders, and stepper-motor actuators while periodically broadcasting CAN status. The ECT (Enhanced Capture Timer) module captures encoder pulses in hardware at low CPU overhead, freeing the 16 MHz core for display update math. The 10-bit ADC with 8 input channels reads NTC thermistors for cabin temperature sensing to within 0.5C when used with an external op-amp buffer. Operating over -40C to +125C, the part survives under-dash thermal stress, and its 5V tolerance lets it drive common anode LED arrays without series resistors sized for 3.3V logic.
おすすめ
Industrial Sensor Node with CANopen
Industrial pressure, level, and flow transmitters use the MC9S12C32VFAE16 to combine sensor signal conditioning, CANopen DS301 communication, and local diagnostics in a single 48-LQFP footprint. The 8-channel 10-bit ADC handles multiple 4-20 mA loop inputs through external resistor dividers, and the SPI bus drives a front-end DAC for 4-20 mA loop output. The 32 KB Flash supports CANopen stack plus application-specific calibration, and the BDM interface enables field firmware upgrades on installed instruments. The part's 5V I/O eases connection to 4-20 mA current loops that are 24V loop-powered, with a wide 2.97-5.5V supply simplifying AC/DC rectified supply rails.
おすすめ
LIN-to-CAN Gateway Bridge
The MC9S12C32VFAE16 serves as a low-cost LIN-to-CAN bridge that aggregates LIN sub-net periph (window, mirror, seat) into an upstream CAN backbone. The SCI (UART) module is re-deployed for LIN 2.x framing under software bit-banging or via external LIN SBC (system basis chip) assistance, while msCAN handles the upstream CAN side. The 16 MHz bus clock computes LIN 20 kbit/s timing with predictable jitter, and 2 KB RAM holds 1-2 LIN frame buffers and a CAN transmit queue. The 48-LQFP package survives under-hood layout when paired with an external LIN transceiver that carries the physical bus.
おすすめ
Drone ESC Sub-Controller
Small-format drone electronic speed controllers (ESCs) use the MC9S12C32VFAE16 as a sub-controller that runs propeller-imbalance diagnostics and motor-temperature telemetry over CAN to the flight-control network. The ECT module reads back-EMF zero-cross events at the 16 MHz bus rate, while the 10-bit ADC samples motor current via a hall-effect sensor. The 32 KB Flash stores sensor-fusion algorithms, and the 48-LQFP package has the thermal headroom needed at moderate PWM switching losses when mounted to a 2 oz copper pour. The 5V tolerant I/O drives optocouplers or gate drivers without level shifters.
おすすめ
Battery Management Slave Cell Monitor
Modular BMS systems use the MC9S12C32VFAE16 as a daisy-chained slave that monitors 6-12 series Li-ion cells and forwards CAN-based telemetry to a master controller. The 10-bit ADC handles cell-voltage measurements to 5 mV accuracy with external resistor dividers, while the SPI bus reads an external temperature sensor. The msCAN module shares the bus with adjacent slaves and the master, and the BDM interface permits firmware updates without disassembly. With its -40C to +125C rating, the part tolerates under-pack thermal rise during fast-charge cycling.
おすすめ
Medical Bed / Adjustable Patient Chair Controller
Hospital bed and lift-chair controllers use the MC9S12C32VFAE16 to coordinate actuator position, load-cell safety cutoff, and remote-control decoding. The ECT module captures quadrature encoder feedback from linear actuators, and the ADC monitors force sensors. The msCAN interface links the controller into the broader hospital-room CAN network for nurse-call integration. The wide 5V supply tolerance and reliable S12C family pedigree meet the long lifecycle requirements of medical equipment, and the 48-LQFP package simplifies hand rework during field service. Note: medical IEC 60601 compliance is system-level, not MCU-level.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S12C32VFAE16 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12C32VFAE10 | MC9S12C32VFAE25 | MC9S12C32MFAE16 | MC9S12GC32VFAE | MC9S12C128VFAE | MC9S12GC16MFAE |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (VFAE) 7x7 mm | 48-LQFP (VFAE) - same | 48-LQFP (VFAE) - same | 48-LQFP (MFAE) - same | 48-LQFP (VFAE) - same | 48-LQFP (VFAE) - same | 48-LQFP (MFAE) - same |
| Core | HCS12 16-bit | HCS12 16-bit | HCS12 16-bit | HCS12 16-bit | S12GC (HCS12-core) | HCS12 16-bit | S12GC (HCS12-core) |
| Flash Size | 32 KB | 32 KB - same | 32 KB - same | 32 KB - same | 32 KB - same | 128 KB (+300%) | 16 KB (-50%) |
| RAM Size | 2 KB | 2 KB - same | 2 KB - same | 2 KB - same | 2 KB - same | 4 KB (+100%) | 1 KB (-50%) |
| Bus Speed | 16 MHz | 10 MHz (-38%) | 25 MHz (+56%) | 16 MHz - same | 25 MHz (+56%) | 25 MHz (+56%) | 16 MHz - same |
| CAN (msCAN) | Yes (1 module) | Yes (1 module) - same | Yes (1 module) - same | Yes (1 module) - same | Yes (1 module) - same | Yes (1 module) - same | Yes (1 module) - same |
| Number of I/O | 31 | 31 - same | 31 - same | 31 - same | 31 - same | 31 - same | 31 - same |
| Operating Temperature | -40C to +125C | -40C to +125C - same | -40C to +125C - same | -40C to +125C - same | -40C to +125C - same | -40C to +125C - same | -40C to +125C - same |
主な差別化要因
- Integrated msCAN 2.0 A/B reduces BOM （vs MC9S08DV128CLF)
- 5V-tolerant I/O simplifies automotive integration （vs MC9S12C32CFUE16 (80-QFP variant))
- BDM debug mode without high-voltage supply （vs MC9S12GC32VFAE (successor family))
設計ノート
The MC9S12C32VFAE16 includes an internal bandgap voltage regulator that derives the core 2.5V from the external 5V supply; bypass VDDR/VSS with a 100 nF and 4.7 uF low-ESR ceramic pair placed within 5 mm of the pin. Estimated: at 16 MHz and full peripheral activity, the core current draws approximately 25-35 mA from VDD - plan decoupling and trace width accordingly. Do not back-drive VDDR.
Keep the BKGD and MODC pins on a 2x5 0.1-inch header for BDM programming and field firmware updates. Place the 4-layer stackup as signal/ground/power/signal so the inner ground plane provides a clean reference for the noisy SPI/SCI lines and the CANTX/CANRX pair driven into the msCAN module. Estimate: route the CANTX/CANRX differential pair with controlled 100 ohm impedance if using on-board CAN termination.
Do not exceed 5.5V on any I/O pin even though the part is 5V-tolerant - transients from the automotive 12V bus must be clamped externally with TVS diodes. The ADC inputs PAD0-PAD7 share their pin with GPIO; configure them as analog inputs and disable the digital pull-up to avoid leakage-induced ADC error. Failure to do so can shift conversion results by 2-3 LSB.
At 16 MHz with all peripherals enabled, the MC9S12C32VFAE16 dissipates an estimated 0.2-0.4W depending on switching I/O load; the 48-LQFP with 2-layer 1 oz copper raises theta_JA into the 80-90 C/W range. For sealed enclosures, derate I/O switching activity or add small copper pours (estimated 4-6 cm^2 each) on both top and bottom sides to maintain junction below 125C.
コンプライアンス情報
RoHS compliant per distributor listings. Not AEC-Q100 qualified for new automotive designs - evaluate the S12K or S32K family for AEC-Q100 needs. NRND status - confirm with NXP for production schedules.