MC9S12GC32VFAE - 16-Bit HCS12 MCU, 32KB Flash, 25MHz | NXP
部品番号: MC9S12GC32VFAE ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $9.4 | $9.40 |
| 10 | $8.46 | $84.60 |
| 100 | $7.52 | $752.00 |
| 500 | $6.58 | $3,290.00 |
| 1,000 | $5.64 | $5,640.00 |
MC9S12GC32VFAE 概要
What is a 16-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of peripheral blocks (ADC, timers, communication ports, GPIO). 16-bit MCUs such as the HCS12 family occupy the middle ground between low-cost 8-bit devices (PIC, AVR) and high-performance 32-bit Cortex-M parts, offering more arithmetic headroom and larger addressable memory while keeping deterministic interrupt latency and low power consumption for real-time control.
Key features include 32KB Flash organized as 32K x 8, 2KB SRAM, 1KB byte-erasable EEPROM for data storage, an SCI (UART) and SPI port for master/slave peripherals, an 8-channel CAN 2.0A/B module compliant with ISO 11898 for in-vehicle networking, a 10-bit 10-channel successive-approximation ADC, and a 16-bit timer/PWM module. The CPU12 core supports a BDM (Background Debug Mode) interface for in-circuit emulation and Flash programming. The 48-LQFP package (7x7 mm) offers an industry-standard surface-mount footprint.
The MC9S12GC32VFAE uses NXP's HCS12 architecture with an enhanced instruction set, 16-bit registers, indexed addressing modes, and a memory-mapped peripheral model. Internal phase-locked loop (IPLL) multiplies an external 4 MHz crystal up to the 25 MHz bus clock, simplifying EMC-compliant board design by avoiding high-frequency external oscillators.
Typical applications include automotive body controllers and CAN nodes, HVAC and appliance control panels, motor control boards for small BLDC and stepper drivers, smart sensor hubs, and low-cost industrial PLC I/O cards. Its combination of CAN 2.0, SCI/SPI, and ADC makes it an efficient single-chip solution for distributed nodes that previously required a separate CAN transceiver and ADC.
Design consideration: the 48-LQFP (7x7) package has moderate thermal performance and the part should be operated within the automotive temperature range (-40C to +105C for the VFAE suffix). Decoupling capacitors must be placed within 3 mm of each VDD/VSS pair, and the RESET pin should be pulled up to VDDR through a 4.7 kohm resistor with a 1 nF to 100 nF decoupling cap.
This page synthesizes distributor stock and pricing, drop-in compatible HCS12 alternatives, and practical design considerations not consolidated in the NXP product folder.
ドロップイン代替品: MC9S12GC32VFAE — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC9S12GC32VFAE （同一形状・フットプリント） — 相違点: Core Processor, Package, Peripherals, Program Memory Size, Supply Voltage.
クイック比較ツール — 並列比較する代替部品を選択:
MC9S12C32VFAE
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12C32VFAE25
✅ ドロップイン✓ 在庫あり
価格はお問い合わせください
データシートを見る →MC9S12C32MFAE25
✅ ドロップイン✓ 在庫あり
$6.4 / 個
データシートを見る →MC9S12GC32VFAE16
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12GC32CFAE16
✅ ドロップイン📋 参考代替品（カタログ未掲載）
MC9S12GC32VFAE 最大定格＆電気的特性
| Core | CPU12 (HCS12) |
| Core Architecture | 16-bit |
| Series | HCS12 (Goldfish / MC9S12C) |
| Program Memory (Flash) | 32 KB (32K x 8) |
| RAM | 2 KB |
| EEPROM | 1 KB (byte-erasable) |
| Maximum CPU Frequency | 25 MHz |
| パッケージ | 48-LQFP (7x7 mm) |
| 実装タイプ | Surface Mount |
| 動作温度 | -40C to +105C (automotive) |
| ADC | 10-bit, 10 channels |
| CAN Module | MSCAN (CAN 2.0A/B), 8 channels |
| SCI / UART | 1 channel |
| SPI | 1 channel |
| Timers | 16-bit TIM/PWM module + 8-bit MOD timer |
| GPIO | Up to 35 (package dependent) |
| Debug Interface | BDM (Background Debug Mode) |
| Supply Voltage (VDD) | 2.35 V to 2.75 V |
| I/O Supply (VDDR) | 2.35 V to 5.5 V |
| MSLレベル | 3 |
| RoHS ステータス | Compliant |
MC9S12GC32VFAE ピン構成
| ピン 1 | PWM3 / IOC3 — Timer/PWM channel 3 or general I/O |
| ピン 2 | PWM5 / IOC5 — Timer/PWM channel 5 or general I/O |
| ピン 3 | BKGD — Background Debug Mode (BDM) data |
| ピン 4 | GND — Ground |
| ピン 5 | RESET — Active-low reset, open-drain with internal pull-up |
| ピン 6 | VDDR — I/O supply voltage (2.35-5.5 V) |
| ピン 7 | VSSX — Crystal oscillator ground |
| ピン 8 | EXTAL — External clock input / crystal pin 1 |
| ピン 9 | XTAL — Crystal pin 2 |
| ピン 10 | VDDX — Crystal oscillator supply |
| ピン 11 | PAD0 / AN0 — GPIO or ADC input channel 0 |
| ピン 12 | PAD1 / AN1 — GPIO or ADC input channel 1 |
| ピン 13 | PAD2 / AN2 — GPIO or ADC input channel 2 |
| ピン 14 | PAD3 / AN3 — GPIO or ADC input channel 3 |
| ピン 15 | PAD4 / AN4 — GPIO or ADC input channel 4 |
| ピン 16 | PAD5 / AN5 — GPIO or ADC input channel 5 |
| ピン 17 | PAD6 / AN6 — GPIO or ADC input channel 6 |
| ピン 18 | PAD7 / AN7 — GPIO or ADC input channel 7 |
| ピン 19 | VRH — ADC high reference voltage |
| ピン 20 | VRL — ADC low reference voltage |
| ピン 21 | VDDAD — ADC supply voltage |
| ピン 22 | VSSAD — ADC ground |
| ピン 23 | PM0 / IOC0 — Port M bit 0 / TIM channel 0 |
| ピン 24 | PM1 / IOC1 — Port M bit 1 / TIM channel 1 |
| ピン 25 | PM2 / IOC2 — Port M bit 2 / TIM channel 2 |
| ピン 26 | PM3 / IOC3 — Port M bit 3 / TIM channel 3 |
| ピン 27 | PM4 — Port M bit 4 |
| ピン 28 | PM5 — Port M bit 5 |
| ピン 29 | PM6 / RXD — Port M bit 6 / SCI receive |
| ピン 30 | PM7 / TXD — Port M bit 7 / SCI transmit |
| ピン 31 | PS0 / SS — Port S bit 0 / SPI slave select |
| ピン 32 | PS1 / SCK — Port S bit 1 / SPI clock |
| ピン 33 | PS2 / MOSI — Port S bit 2 / SPI master-out |
| ピン 34 | PS3 / MISO — Port S bit 3 / SPI master-in |
| ピン 35 | CANRX — MSCAN receive input |
| ピン 36 | CANTX — MSCAN transmit output |
| ピン 37 | PJ0 / CAN0TX — Port J bit 0 |
| ピン 38 | PJ1 / CAN0RX — Port J bit 1 |
| ピン 39 | PP0 / PWM0 — Port P bit 0 / PWM channel 0 |
| ピン 40 | PP1 / PWM1 — Port P bit 1 / PWM channel 1 |
| ピン 41 | PP2 / PWM2 — Port P bit 2 / PWM channel 2 |
| ピン 42 | PP3 / PWM3 — Port P bit 3 / PWM channel 3 |
| ピン 43 | PP4 / PWM4 — Port P bit 4 / PWM channel 4 |
| ピン 44 | PP5 / PWM5 — Port P bit 5 / PWM channel 5 |
| ピン 45 | VDDPLL — PLL supply voltage |
| ピン 46 | VSSPLL — PLL ground |
| ピン 47 | VDD — Core supply voltage (2.35-2.75 V) |
| ピン 48 | VSS — Core ground |
主な用途
MC9S12GC32VFAE の用途: 6 件s: Automotive CAN Node / Body Control Module, Industrial Sensor Hub / Remote I/O Node, Small BLDC / Stepper Motor Controller, Smart Appliance Control Board, Lighting Control Module (DALI / 0-10V), Battery-Management Monitoring Slave.
Automotive CAN Node / Body Control Module
The MC9S12GC32VFAE's integrated MSCAN (CAN 2.0A/B) controller and 32KB Flash make it a natural fit for distributed automotive body-control and CAN-node applications. Placed at the leaf-node end of a CAN bus, the MCU handles local I/O - switches, LEDs, and sensor conditioning - while the MSCAN hardware autonomously transmits/receives 11-bit and 29-bit identifiers without CPU load. The 48-LQFP (7x7 mm) footprint allows placement in space-constrained behind-panel modules, and the -40C to +105C temperature grade meets cabin and underhood requirements. Pairing the MCU with an external ISO 11898 transceiver (such as NXP TJA1050 or TJA1043) yields a complete CAN-node for body electronics, lighting, or HVAC actuators.
おすすめ
Industrial Sensor Hub / Remote I/O Node
The MC9S12GC32VFAE serves industrial 4-20 mA loop controllers, RS-485 sensor hubs, and remote I/O nodes thanks to its 10-bit 10-channel ADC, SCI (UART) and SPI ports. The ADC's 7 us conversion time at 25 MHz bus clock easily handles industrial 0-10 V or 4-20 mA signal conditioning, while the SPI master can drive external DACs, FRAM, or EEPROM. With 32KB Flash and 2KB RAM, it runs typical 4-20 mA loop transmitter stacks, calibration routines, and Modbus RTU framing on the SCI. The 48-LQFP industrial operating range supports factory-floor deployments.
おすすめ
Small BLDC / Stepper Motor Controller
The MC9S12GC32VFAE's 16-bit TIM/PWM module with PWM/center-aligned capability and 10-bit ADC closes the loop for small brushless DC and stepper motor controllers used in fans, pumps, and small appliances. Six PWM channels drive a 3-phase FET bridge through gate drivers (such as NXP MC33937 or TI DRV8301), while the ADC samples phase currents for sensorless trapezoidal or FOC commutation. The CPU12 core's indexed addressing and BDM debug simplify tuning of the speed-control loop. The automotive temperature grade allows deployment in-vehicle HVAC blower and coolant-pump applications.
おすすめ
Smart Appliance Control Board
White-goods control boards in washing machines, dishwashers, and induction cooktops use the MC9S12GC32VFAE for keypad scanning, display driving, and main motor / heater control. Its 35 GPIO handle segmented LCD bias (via external charge pump), key-matrix scanning, and triac firing. The 32KB Flash fits state-machine code for cycle profiles, while the EEPROM stores user preferences and fault logs. The 48-LQFP surface-mount footprint supports automated assembly in high-volume appliance lines.
おすすめ
Lighting Control Module (DALI / 0-10V)
DALI (Digital Addressable Lighting Interface) controllers and 0-10 V dimmer modules rely on the MC9S12GC32VFAE for protocol handling, dim curve smoothing, and PWM fade generation. The SCI (UART) implements DALI bidirectional half-duplex signaling through an external DALI transceiver, while the TIM/PWM outputs drive constant-current LED drivers with smooth fade transitions. The 2KB RAM stores per-channel fade state and 64 DALI ballast entries, and 32KB Flash fits the IEC 62386 stack with comfortable headroom for custom lighting logic.
おすすめ
Battery-Management Monitoring Slave
As a cell-monitoring slave in a distributed BMS, the MC9S12GC32VFAE reads individual cell voltages through its 10-bit ADC, communicates up the stack via SPI, and broadcasts critical events via CAN (MSCAN). The byte-erasable EEPROM stores calibration data and lifetime cycle counts, while the 32KB Flash implements the cell-balancing algorithm and SPI-to-CAN bridge firmware. The automotive temperature grade and -40C to +105C operation cover underhood and trunk-mounted battery-pack environments.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC9S12GC32VFAE — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC9S12C32VFAE | MC9S12C32VFAE25 | MC9S12C32MFAE25 | MC9S12GC32VFAE16 | MC9S12GC32CFAE16 |
|---|---|---|---|---|---|---|
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| CPU Clock (Max) | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 16 MHz | 16 MHz |
| CAN Module | MSCAN (1x, 8-channel) | MSCAN | MSCAN | MSCAN | MSCAN | MSCAN |
| ADC Channels | 10 (10-bit) | 10 (10-bit) | 10 (10-bit) | 10 (10-bit) | 10 (10-bit) | 10 (10-bit) |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +125C | -40C to +105C | -40C to +85C |
| RoHS Status | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
| Core | HCS12 CPU12 | HCS12 CPU12 | HCS12 CPU12 | HCS12 CPU12 | HCS12 CPU12 | HCS12 CPU12 |
主な差別化要因
- Integrated MSCAN controller for in-vehicle networking （vs MC9S08PA4VTG)
- 32KB Flash vs larger-code-size variants in same package （vs MC9S12XDP512CAG)
- Automotive temperature grade (-40C to +105C) （vs MC9S12GC32CFAE16)
設計ノート
Decouple VDD/VSS pairs with 100 nF X7R ceramic capacitors placed within 3 mm of each pin pair, plus a single 4.7 uF bulk tantalum or ceramic capacitor on each supply rail. The VDDR (I/O supply) pin powers the GPIO drivers; tying it to a regulated 5 V supply enables 5 V-tolerant logic on the GPIO pins. The VDDX (oscillator supply) should be decoupled separately with a 100 nF cap to avoid PLL noise coupling. Estimated: at 25 MHz full operation the core consumes approximately 30-40 mA; the I/O supply adds 10-20 mA depending on loading.
The 48-LQFP package has a thermal resistance (theta_JA) of approximately 65 C/W on a 2-layer JEDEC test board. Estimated: at full 25 MHz operation with all peripherals active, dissipation is ~150 mW, leading to a junction temperature rise of ~10C above ambient - well within the 105C automotive grade. For sealed enclosures with no airflow, derate by adding copper pour under the exposed thermal pad area (the 48-LQFP has no exposed pad, so copper pours on both sides are recommended).
Place the 4 MHz crystal (or ceramic resonator) within 5 mm of EXTAL/XTAL with short, symmetric traces to maintain stable oscillation. The RESET pin requires a 4.7 kohm pull-up to VDDR plus a 1 nF-100 nF decoupling cap. Route the BKGD pin adjacent to RESET; BDM pods require both signals. Keep CANRX/CANTX traces short and impedance-controlled (typically 50 ohm single-ended) when connecting to the external CAN transceiver.
Do not leave the RESET pin floating during normal operation - the internal pull-up is weak and noise can cause spurious resets. When using BDM, ensure the BKGD line is not driven by external circuitry during debug. Flash endurance is rated for 10k program/erase cycles - implement wear-leveling if updating EEPROM-backed parameters frequently. The PLL requires lock time (~1 ms) before switching to the PLL clock; do not access peripherals requiring accurate timing before the PLL locks.
コンプライアンス情報
RoHS compliant per NXP product folder. AEC-Q100 qualification status: VFAE suffix is automotive temperature grade (-40C to +105C) but full Q100 qualification status is not explicitly stated in available data - consult NXP for PPAP. Lead-free (Pb-free) 48-LQFP terminations. Halogen-free status unknown from verified data; check NXP product environmental compliance page for confirmation.