MCP3302T-CI/SL - 13-Bit 2-Channel SPI ADC | Microchip
部品番号: MCP3302T-CI/SL ✓ 生産中MCP3302T-CI/SL 概要
An ADC is a semiconductor that converts an analog voltage into a digital code for processing, storage, display, or control. The MCP3302 belongs to the SAR ADC family, where a successive-approximation internal DAC and comparator progressively determine the input voltage. In the power-management IC hierarchy, this converter bridges analog sensor signals and digital embedded systems, while its SPI interface provides a compact means of transferring conversion results to a microcontroller.
The device provides 13-bit conversion resolution, two analog input channels, differential input support, and conversion rates up to 100 kHz. Differential operation rejects common-mode voltage and can improve measurement accuracy when the source is centered around a biased reference. The four single-ended inputs give additional flexibility for multiplexed measurements, while the SPI interface supports integration with embedded controllers without requiring a parallel data bus.
The MCP3302 architecture uses a successive-approximation conversion process with an internal sample-and-hold function. During conversion, the SAR logic drives an internal DAC through successive bit trials until the internal comparator matches the sampled input voltage. The resulting 13-bit code is transferred through the serial interface. Exact input impedance, acquisition time, reference requirements, and current consumption must be confirmed from the manufacturer datasheet before defining the input network or acquisition timing.
Typical uses include ratiometric pressure and temperature sensing, potentiometer position measurement, bridge-sensor instrumentation, industrial process monitoring, battery-powered remote data acquisition, and embedded control systems. The differential inputs are especially useful when a sensor output is referenced to a biased common-mode voltage. For low-level signals, careful grounding, reference filtering, and input-conditioning design remain essential because converter accuracy depends on the complete analog front end rather than on resolution alone.
For each SPI transaction, use the manufacturer timing diagram to account for CS setup, sample-and-hold acquisition, conversion time, SCLK frequency, and output-data timing. Place the reference and input bypass capacitors close to their associated pins, maintain a low-impedance ground return, and avoid routing sensitive analog inputs adjacent to fast SPI clock traces. The MCP3302 datasheet and pin-description table should be used as the authority for board design and firmware sequencing.
This page combines the exact MCP3302T-CI/SL package and interface details with a pin-compatible comparison, application guidance, and practical SPI interface considerations. It also identifies which specifications require direct confirmation from the manufacturer datasheet, helping engineers plan sensor acquisition before committing to PCB layout or embedded firmware.
ドロップイン代替品: MCP3302T-CI/SL — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP3302T-CI/SL (同一形状・フットプリント) — 相違点: Package, Converter Type, Digital Interface, Maximum Conversion Rate, Number of Input Channels.
MCP3302-CI/SL
✅ ドロップイン価格はお問い合わせください
データシートを見る →MCP3301T-BI/SN
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →MCP3201T-CI/SL
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MCP3201T-I/SL
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MCP3202T-CI/SL
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
MCP3302T-CI/SL 最大定格&電気的特性
| Converter Type | 13-bit successive-approximation ADC |
| Number of Input Channels | 2 differential input channels |
| Single-Ended Input Configuration | 4 single-ended inputs |
| Maximum Conversion Rate | 100 kHz |
| Supply Voltage Range | 4.5 V to 5.5 V |
| インターフェース | SPI serial interface |
| Architecture | SAR ADC |
| パッケージ | 14-pin SOIC |
| 実装タイプ | Surface mount |
| Analog Input Type | Differential |
| AEC-Q100 Qualification | not_applicable |
MCP3302T-CI/SL ピン構成
| ピン 1 | CS — Chip-select input |
| ピン 2 | CH0- — Differential input channel 0 negative input |
| ピン 3 | CH0+ — Differential input channel 0 positive input |
| ピン 4 | CH1- — Differential input channel 1 negative input |
| ピン 5 | CH1+ — Differential input channel 1 positive input |
| ピン 6 | VSS — Analog ground |
| ピン 7 | VDD — Positive analog supply |
| ピン 8 | DIN — Serial data input |
| ピン 9 | SCLK — Serial clock input |
| ピン 10 | DOUT — Serial data output |
| ピン 11 | DNC — Not connected (per datasheet) |
| ピン 12 | DNC — Not connected (per datasheet) |
| ピン 13 | DNC — Not connected (per datasheet) |
| ピン 14 | VREF — Positive reference input |
主な用途
MCP3302T-CI/SL の用途: 6 件s: Industrial Sensor Acquisition, Battery-Powered Remote Monitoring, Pressure and Bridge Measurement, Instrumentation and Test Equipment, Potentiometer Position Measurement, Embedded Control Systems.
Industrial Sensor Acquisition
The MCP3302T-CI/SL fits industrial sensor acquisition because its two differential channels can measure balanced sensor outputs while rejecting common-mode noise present in factory environments. The 13-bit resolution provides 8192 codes across the selected input range, and the 100 kHz conversion rate supports multiple sampled measurements. A practical implementation would condition each sensor with an amplifier, protect the inputs, and route them to CH0+ and CH0- or CH1+ and CH1-. Differential wiring is valuable when the sensor output is centered around a biased reference rather than ground. Firmware should select the correct input configuration, wait for acquisition, and control CS and SCLK according to the manufacturer timing diagrams.
おすすめ
Battery-Powered Remote Monitoring
The MCP3302T-CI/SL is appropriate for battery-powered remote monitoring because Microchip identifies the MCP3302 as a low-power ADC designed for portable and remote data-acquisition systems. Its 4.5 V to 5.5 V operating range requires a compatible regulator or battery configuration, while the two differential channels reduce the need for separate analog front ends. A field sensor can drive one differential pair, with the second available for a second measurement or diagnostic input. Duty-cycling the converter and its support circuitry can reduce average energy use. The design should verify converter current, shutdown behavior, reference stability, and acquisition timing from the datasheet before estimating battery life.
おすすめ
Pressure and Bridge Measurement
The MCP3302T-CI/SL can digitize outputs from resistive bridge sensors used in pressure, force, and load measurement. Two differential inputs allow a bridge output to be measured relative to its excitation reference while a second channel can monitor a temperature or reference signal. The SAR converter's 13-bit result and 100 kHz rate are useful for slow mechanical measurements, while differential operation helps suppress excitation-related common-mode voltage. The analog front end still determines overall accuracy: use a regulated excitation source, matched input filtering, and a quiet reference arrangement. Firmware should perform offset and gain calibration against known sensor conditions before reporting engineering units.
おすすめ
Instrumentation and Test Equipment
The MCP3302T-CI/SL is suitable for compact instrumentation that must capture analog test points without allocating a parallel ADC bus. Its SPI interface reduces wiring between the converter and a controller, while two differential inputs support active or bridge-coupled measurements. At up to 100 kHz, the converter can acquire process-control and diagnostic signals faster than many slow sensor mechanisms require. A practical instrument would use separate analog and digital grounding strategies, bypass the reference and supply pins locally, and place the ADC close to the input connector. Firmware should retain signed or unsigned code interpretation consistently and preserve the manufacturer's timing intervals for acquisition and conversion.
おすすめ
Potentiometer Position Measurement
The MCP3302T-CI/SL can measure resistive potentiometer or other divider-based position sensors when the divider is excited from the ADC supply and referenced accurately. The 13-bit resolution supports coarse position readings in control panels, actuator feedback, and laboratory equipment, although mechanical repeatability and reference stability may limit real accuracy. One differential channel can represent the divider wiper relative to a sensed reference potential, while another channel can monitor a second axis or diagnostic voltage. The input source impedance must be checked against the converter's acquisition requirements so that the sampling capacitor can settle. Add suitable filtering at the input, but keep the filter capacitance within the acquisition and charge-sharing constraints stated in the datasheet.
おすすめ
Embedded Control Systems
The MCP3302T-CI/SL integrates naturally with embedded controllers that use SPI, making it appropriate for mixed-signal control boards with analog sensing and digital processing. A microcontroller can issue commands over CS and SCLK, receive the 13-bit result through the serial output, and apply calibration or threshold logic. The converter's 100 kHz maximum rate allows sampled feedback loops, although loop bandwidth must remain compatible with acquisition and SPI transaction latency. Keep the analog section away from processor clocks and switching supplies, provide local bypass capacitance, and use a separate reference arrangement if the system requires better stability than the supply rail can provide.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP3302T-CI/SL — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCP3302-CI/SL | MCP3301T-BI/SN | MCP3201T-CI/SL | MCP3201T-I/SL | MCP3202T-CI/SL |
|---|---|---|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | 13 bit | 13 bit | 13 bit | 12 bit | 12 bit | 12 bit |
| Number of Differential Channels | 2 channels | 2 channels | 1 channel | 1 channel | 1 channel | 2 channels |
| Conversion Architecture | SAR ADC | SAR ADC | SAR ADC | SAR ADC | SAR ADC | SAR ADC |
| Serial Interface | SPI | SPI | SPI | SPI | SPI | SPI |
| Input Configuration | Differential inputs | Differential inputs | Differential inputs | Differential inputs | Differential inputs | Differential inputs |
| Orderable Suffix | T-CI/SL | CI/SL | BI/SN | CI/SL | I/SL | CI/SL |
主な差別化要因
- Higher resolution than MCP3202T-CI/SL (vs MCP3202T-CI/SL)
- Two differential channels instead of one (vs MCP3301T-BI/SN)
- One-bit resolution advantage over MCP3201T-CI/SL (vs MCP3201T-CI/SL)
設計ノート
Place the MCP3302T-CI/SL close to the analog source and route CH0+, CH0-, CH1+, and CH1- away from SCLK, DOUT, and switching-node traces. Keep the analog ground connection short and follow the manufacturer's grounding guidance for VSS and the reference connection. Local bypass capacitors should connect directly to the relevant supply or reference pins with minimal loop area. This arrangement is important because a 13-bit converter can still deliver poor system accuracy when the analog traces pick up coupling from digital or switching circuitry.
Design SPI firmware around the manufacturer's minimum CS, acquisition, conversion, and clock timing values. Assert CS before starting the conversion sequence, allow the analog input to settle for the required acquisition interval, and then read the 13-bit result using the documented clock and data-edge convention. Do not infer a safe SCLK rate solely from the 100 kHz conversion-rate figure. Validate timing with an oscilloscope on the finished PCB, including trace delay, microcontroller output delay, and any level-shifting components.
Avoid treating a family member with the same SOIC pin count as an automatic drop-in replacement. The MCP3301-family candidates provide one differential channel rather than two, and the MCP3201/MCP3202 options reduce resolution by one bit. Confirm the exact pin functions, input ranges, reference arrangement, temperature grade, and qualification status in the manufacturer documentation. PCB changes may also be necessary if the replacement uses a different exposed-pad, reference, or supply arrangement.
Decouple VDD locally and provide a stable reference network for the analog conversion. If the reference is derived from VDD, verify that supply variation, temperature drift, and loading are acceptable for the required measurement accuracy; a dedicated reference may be preferable when the ADC output drives a precision measurement. Confirm reference bypass requirements and permissible reference current in the datasheet. Decoupling capacitance and any additional filtering should be selected so that the source impedance does not prevent complete sampling during the acquisition interval.
コンプライアンス情報
Compliance attributes require confirmation from the manufacturer product documentation. AEC-Q100 is not applicable to this industrial analog converter.