MCP604T-I/ST - Quad 2.8MHz Low-Power Op Amp | Microchip
MPN: MCP604T-I/ST ✓ 啟用中MCP604T-I/ST 概覽
An operational amplifier is an active analog signal-conditioning device that uses high open-loop gain to amplify small differential inputs. The MCP604 belongs to the CMOS operational-amplifier hierarchy, where rail-to-rail output swing allows the output voltage to approach the supply rails more closely than a conventional amplifier with a restricted output range. Four independent amplifiers in the MCP604 can perform buffering, amplification, filtering, comparison, or level-shifting functions while conserving board area.
Key features include four amplifier channels, a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, low input bias current, high open-loop gain, and rail-to-rail output swing. The 2.7 V to 6 V operating range allows the device to operate from single 3.3 V or 5 V rails as well as conventional low-voltage analog systems. The industrial-temperature ordering code MCP604T-I/ST identifies the temperature grade and TSSOP packaging option.
Microchip's advanced CMOS process gives the MCP604 low bias current, high-speed operation, high open-loop gain, and rail-to-rail output capability. Its 2.8 MHz gain-bandwidth product is sufficient for audio-frequency, general-purpose, and low-to-moderate-bandwidth signal paths. Because the amplifier is intended for low-power systems, stable operation also depends on correct input/output capacitor selection, suitable bypassing, and keeping sensitive input traces away from switching nodes.
Typical uses include portable sensor interfaces, low-power data acquisition, industrial transducers, audio signal conditioning, battery-powered measurement equipment, and general analog buffering. Four channels can process related signals simultaneously or provide independent gain stages around a microcontroller, ADC, or sensor network. The low operating current helps limit system power when the amplifier operates continuously, although the final system dissipation also depends on load and supply voltage.
For stable operation, place the bypass capacitor close to the supply pin, use the manufacturer-recommended feedback network, and verify output-swing and common-mode limits against the actual signal and supply levels. Avoid placing high-impedance input traces beside noisy switching paths, and use a low-impedance source where the source impedance could create bias-current errors. The TSSOP footprint also requires adequate board spacing for soldering and inspection.
This product record combines the manufacturer architecture information, exact ordering information, package details, and verified sourcing context. It also provides engineering-focused alternatives, application guidance, comparison parameters, and practical design notes to help evaluate the MCP604T-I/ST before PCB implementation.
直接替換替代品,適用於 MCP604T-I/ST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP604T-I/ST (相同外形與佔位) — 差異在於 Package, Amplifier Type, Number of Channels, Amplifier Count, Input Common-Mode Range.
MCP604T-E/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP604T-E/STVAO
✅ 直接替換📋 參考替代品(不在目錄中)
MCP604T-I/SL
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP604T-I/ST 最大額定值與電氣特性
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 6 V |
| Output Swing | Rail-to-rail |
| 封裝 | 14-pin TSSOP |
| 安裝類型 | Surface mount |
| Process Technology | Advanced CMOS |
MCP604T-I/ST 14-pin tssop 腳位配置指南
MCP604T-I/ST(14-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP604T-I/ST.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP604T-I/ST 適用於 6 應用s: Portable Sensor Signal Conditioning, Industrial Transducer Interface, Low-Power Data Acquisition, Audio Signal Buffering, Battery-Powered Measurement, Embedded Analog Control.
Portable Sensor Signal Conditioning
The MCP604T-I/ST fits portable sensor interfaces because its four channels can amplify, buffer, and filter several low-level signals while the typical operating current is only 230 uA. The 2.7 V minimum supply voltage supports compact, low-energy systems operating from a 3.3 V rail. Place each amplifier close to its sensor or connector, bypass the supply locally, and use short, guarded traces to limit noise pickup. The 2.8 MHz gain-bandwidth product provides useful bandwidth for common pressure, temperature, and resistive-sensor signals, although sensor-specific filtering and input-offset requirements still need verification.
推薦
Industrial Transducer Interface
The MCP604T-I/ST is appropriate for industrial transducer conditioning where a 2.7 V to 6 V supply, low typical operating current of 230 uA, and four independent amplifier channels simplify analog front ends. Its 2.8 MHz gain-bandwidth product can support general-purpose measurement paths with moderate bandwidth. Use one channel for a sensor signal, other channels for excitation, reference conditioning, or output buffering, and observe ESD protection requirements at external connectors. The industrial ordering code should be checked against the actual enclosure temperature and production qualification requirements.
推薦
Low-Power Data Acquisition
The MCP604T-I/ST can condition four analog inputs before digitization in a compact data-acquisition system. Its 230 uA typical operating current limits the amplifier contribution to standby consumption, while the 2.8 MHz gain-bandwidth product is suitable for many sensor-bandwidth signals. Configure gain carefully so the closed-loop bandwidth remains appropriate for the signal, and account for input offset and bias-current error when using high-impedance sources. Local supply bypassing and short feedback paths are essential for repeatable measurements at low signal levels.
推薦
Audio Signal Buffering
The MCP604T-I/ST is useful for audio signal buffering and gain stages where rail-to-rail output operation helps preserve signal range in low-voltage systems. Its 2.8 MHz gain-bandwidth product covers a substantial portion of the audio band, and four channels allow paired stereo buffering plus additional monitoring or control paths. Confirm the required gain-bandwidth product, output-load conditions, distortion criteria, and noise performance for the selected gain and frequency. Keep input and output routing short and decouple the supply close to the device to reduce channel-to-channel interaction.
推薦
Battery-Powered Measurement
The MCP604T-I/ST is well suited to battery-powered measurement instruments because it starts at 2.7 V, consumes 230 uA typically, and integrates four amplifier channels. The device can condition battery voltage, sensor outputs, and status signals without requiring a large number of separate packages. Use the lowest supply voltage that still provides adequate output swing and common-mode headroom, and disable or bypass unneeded channels according to the family documentation. Battery-life estimates should include regulator quiescent current, ADC activity, and the load driven by each amplifier output.
推薦
Embedded Analog Control
The MCP604T-I/ST can provide four independent analog functions around an embedded controller, including sensor amplification, actuator feedback, reference buffering, and threshold conditioning. The 2.7 V to 6 V range is compatible with common embedded rails, while 230 uA typical current supports low-power operation. The package reduces routing complexity by grouping four channels in one 14-pin TSSOP footprint. Keep sensitive feedback and reference nets away from MCU clock and power-converter traces, and verify output drive against the connected ADC, DAC, or actuator input.
推薦
推薦產品摘要
工程參考資料,適用於 MCP604T-I/ST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP604T-E/ST | MCP604T-E/STVAO | MCP604T-I/SL |
|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Process Technology | Advanced CMOS | Advanced CMOS | Advanced CMOS | Advanced CMOS |
| Ordering Grade | Industrial I grade | E grade | Automotive-oriented VAO ordering option | Industrial I grade |
主要差異化特點
- Four independent amplifiers in one compact package (對比MCP604T-E/ST)
- Low operating current for four-channel analog conditioning (對比MCP604T-E/STVAO)
- Single-supply compatibility (對比MCP604T-E/ST)
設計說明
Place the supply bypass capacitor directly between the MCP604T-I/ST supply and ground pins, keeping the connection loop short and the return path close to the device. Route sensitive input and feedback traces away from digital clock lines, switching-regulator nodes, and the amplifier outputs. With four channels in a 14-pin TSSOP, plan the fanout so each amplifier's feedback components remain close to the associated input and output pins and do not force signals around the package.
Choose closed-loop gain with the 2.8 MHz gain-bandwidth product in mind. Higher gain reduces the usable closed-loop bandwidth, so a gain of 10 leaves substantially less bandwidth than unity gain. When driving a capacitive load, add an isolation resistor near the amplifier output and verify stability. For high-impedance sensors, account for input bias-current error and leakage by keeping the source impedance within the manufacturer-recommended range.
Do not interpret the 2.7 V minimum supply rating as permission to operate every output at either rail under every load. Check the input common-mode range, output-swing curve, capacitive-load behavior, and shutdown-channel configuration in the manufacturer datasheet. Likewise, avoid assuming that the four amplifier channels are interchangeable in every operating mode; identify unused inputs and outputs according to the official pin-description and application guidance.
The 230 uA value is a typical family operating-current specification, not a complete system-power limit. Actual current depends on supply voltage, amplifier activity, output load, and the selected operating mode. For battery designs, calculate the amplifier contribution at the intended duty cycle and include regulator, ADC, logic, and indicator currents. Use the most efficient operating configuration that still meets settling-time and noise requirements.
合規資訊
The standard MCP604T-I/ST is not identified as an automotive-qualified ordering option. The automotive-oriented MCP604T-E/STVAO alternative should be selected when automotive qualification is specifically required.